/openbmc/qemu/docs/config/ |
H A D | ich9-ehci-uhci.cfg | 7 # controllers as multifunction device in PCI slot "1d". 16 multifunction = "on" 21 multifunction = "on" 28 multifunction = "on" 35 multifunction = "on"
|
H A D | q35-emulated.cfg | 81 multifunction = "on" 89 multifunction = "on" 97 multifunction = "on" 105 multifunction = "on" 171 multifunction = "on" 177 multifunction = "on" 185 multifunction = "on" 193 multifunction = "on" 207 multifunction = "on" 213 multifunction = "on" [all …]
|
H A D | q35-virtio-serial.cfg | 85 multifunction = "on"
|
/openbmc/linux/arch/s390/pci/ |
H A D | pci_iov.c | 57 virtfn->multifunction = 0; in zpci_iov_link_virtfn() 71 if (!zbus->multifunction) in zpci_iov_setup_virtfn()
|
H A D | pci_bus.c | 196 zbus->multifunction = fr->rid_available; in zpci_bus_create_pci_bus() 309 if (zbus->multifunction && !zdev->rid_available) { in zpci_bus_add_device()
|
/openbmc/linux/Documentation/devicetree/bindings/iio/adc/ |
H A D | st,stmpe-adc.yaml | 7 title: ADC on an STMPE multifunction device. 13 This ADC forms part of an ST microelectronics STMPE multifunction device .
|
H A D | x-powers,axp209-adc.yaml | 14 Device is a child of an axp209 multifunction device
|
/openbmc/openbmc/meta-arm/meta-arm-bsp/recipes-kernel/linux/linux-yocto-6.6/n1sdp/ |
H A D | 0002-n1sdp-pci_quirk-add-acs-override-for-PCI-devices.patch | 33 + All multifunction devices - multifunction ACS subset 67 + if (!strncmp(p, "multifunction", 13)) 142 + if (acs_on_multifunction && dev->multifunction)
|
/openbmc/linux/Documentation/devicetree/bindings/mfd/ |
H A D | qriox.txt | 3 The qrio is a multifunction device that controls the KEYMILE boards based on
|
H A D | bfticu.txt | 3 The bfticu is a multifunction device that manages the whole chassis.
|
H A D | mediatek,mt6357.yaml | 18 This is a multifunction device with the following sub modules:
|
H A D | mt6397.txt | 3 MT6397/MT6323 is a multifunction device with the following sub modules:
|
H A D | richtek,rt5033.yaml | 13 RT5033 is a multifunction device which includes battery charger, fuel gauge,
|
/openbmc/linux/Documentation/devicetree/bindings/mips/lantiq/ |
H A D | rcu.txt | 4 This binding describes the RCU (reset controller unit) multifunction device,
|
/openbmc/linux/Documentation/devicetree/bindings/pinctrl/ |
H A D | mediatek,mt6795-pinctrl.yaml | 72 /* GPIO0 set as multifunction GPIO0 */ 78 /* GPIO45 set as multifunction SDA0 */
|
H A D | mediatek,mt8186-pinctrl.yaml | 84 /* GPIO0 set as multifunction GPIO0 */ 90 /* GPIO128 set as multifunction SDA0 */
|
H A D | mediatek,mt8195-pinctrl.yaml | 77 /* GPIO0 set as multifunction GPIO0 */ 83 /* GPIO8 set as multifunction SDA0 */
|
/openbmc/linux/drivers/memstick/host/ |
H A D | Kconfig | 42 multifunction reader)
|
/openbmc/linux/Documentation/devicetree/bindings/power/supply/ |
H A D | richtek,rt5033-charger.yaml | 13 The battery charger of the multifunction device RT5033 has to be instantiated
|
/openbmc/linux/drivers/parisc/ |
H A D | Kconfig | 35 Say Y here to support the Lasi multifunction chip found in 46 Say Y here to support the Wax multifunction chip found in some
|
/openbmc/qemu/docs/ |
H A D | pcie.txt | 118 … -device pcie-root-port,id=root_port1,multifunction=on,chassis=x,addr=z.0[,slot=y][,bus=pcie.0] \ 176 (multifunction) device can be plugged into each Port. This results in 204 uses one bus number. Since only one (multifunction) device 255 Leave enough PCI Express Root Ports empty. Use multifunction
|
/openbmc/linux/arch/s390/include/asm/ |
H A D | pci.h | 112 bool multifunction; member
|
/openbmc/linux/Documentation/driver-api/ |
H A D | sm501.rst | 9 The Silicon Motion SM501 multimedia companion chip is a multifunction device
|
/openbmc/linux/drivers/leds/flash/ |
H A D | Kconfig | 48 multifunction device. It has build in control for two leds in flash
|
/openbmc/linux/arch/powerpc/kernel/ |
H A D | pci_of_scan.c | 191 dev->multifunction = 0; /* maybe a lie? */ in of_create_pci_dev()
|