/openbmc/linux/Documentation/hwmon/ |
H A D | ntc_thermistor.rst | 56 -+- (ground) 68 -+- (ground) 80 -+----+- (ground) 92 -+- (ground)
|
H A D | smsc47m192.rst | 108 to ground or Vcc. '1' indicates a diode fault.
|
H A D | adm1026.rst | 96 voltage from the power lead rather than on the ground lead.
|
/openbmc/linux/drivers/extcon/ |
H A D | extcon-intel-mrfld.c | 98 bool ground; in mrfld_extcon_get_id() local 122 ground = id & BCOVE_USBIDSTS_GND; in mrfld_extcon_get_id() 125 return ground ? INTEL_USB_ID_GND : INTEL_USB_ID_FLOAT; in mrfld_extcon_get_id() 127 return ground ? INTEL_USB_ID_FLOAT : INTEL_USB_ID_GND; in mrfld_extcon_get_id()
|
/openbmc/linux/drivers/iio/position/ |
H A D | Kconfig | 28 and keyboard angle respect to horizon (ground).
|
/openbmc/linux/Documentation/devicetree/bindings/iio/ |
H A D | mount-matrix.txt | 96 ground plane and positive towards magnetic North, (x) is in the ground plane, 98 perpendicular to the ground plane and positive upwards.
|
/openbmc/linux/arch/arm/boot/dts/rockchip/ |
H A D | rk3288-veyron-sdmmc.dtsi | 40 * Builtin CD line is hooked to ground to prevent JTAG at boot
|
/openbmc/linux/drivers/auxdisplay/ |
H A D | Kconfig | 378 0 : no connection (eg: connected to ground) 393 0 : no connection (eg: connected to ground) 408 0 : no connection (eg: connected to ground) 423 0 : no connection (eg: connected to ground) 438 0 : no connection (eg: connected to ground) 453 0 : no connection (eg: connected to ground)
|
/openbmc/linux/Documentation/w1/ |
H A D | w1-generic.rst | 6 signal wire (plus ground, so two wires). 8 Devices communicate on the bus by pulling the signal to ground via an open
|
/openbmc/linux/arch/arm64/boot/dts/qcom/ |
H A D | sc7180-trogdor-lazor.dtsi | 12 semtech,cs0-ground;
|
/openbmc/linux/Documentation/devicetree/bindings/sound/ |
H A D | rt5645.txt | 25 contacts to the ground or floating. It could avoid some electric noise from the
|
/openbmc/linux/rust/alloc/ |
H A D | README.md | 27 We agreed on a middle-ground: we would keep a subset of `alloc`
|
/openbmc/linux/Documentation/admin-guide/media/ |
H A D | cec.rst | 332 The ground pin of the HDMI connector needs to be connected to a ground 369 and two female-female breadboard wires: one for connecting the HDMI ground 370 pin to a ground pin on the Raspberry Pi, and the other to connect the HDMI
|
/openbmc/linux/arch/arm/boot/dts/marvell/ |
H A D | kirkwood-openblocks_a7.dts | 84 * ground.
|
/openbmc/qemu/docs/devel/ |
H A D | code-of-conduct.rst | 9 To that end, we have a few ground rules that we ask people to adhere to.
|
/openbmc/u-boot/doc/device-tree-bindings/gpio/ |
H A D | gpio-pcf857x.txt | 4 driven high by a pull-up current source or driven low to ground. This combines
|
/openbmc/linux/Documentation/misc-devices/ |
H A D | lis3lv02d.rst | 95 fall to the ground is out of question...
|
/openbmc/linux/Documentation/ABI/testing/ |
H A D | sysfs-bus-iio | 662 1kohm_to_gnd: connected to ground via an 1kOhm resistor, 663 2.5kohm_to_gnd: connected to ground via a 2.5kOhm resistor, 664 6kohm_to_gnd: connected to ground via a 6kOhm resistor, 665 20kohm_to_gnd: connected to ground via a 20kOhm resistor, 666 90kohm_to_gnd: connected to ground via a 90kOhm resistor, 667 100kohm_to_gnd: connected to ground via an 100kOhm resistor, 668 125kohm_to_gnd: connected to ground via an 125kOhm resistor, 669 500kohm_to_gnd: connected to ground via a 500kOhm resistor, 670 640kohm_to_gnd: connected to ground via a 640kOhm resistor, 1869 * Y is in the ground plane and positive towards magnetic North ; [all …]
|
/openbmc/qemu/docs/specs/ |
H A D | fsi.rst | 59 necessary to get FSI off the ground thanks to the mapping of the CFAM address
|
/openbmc/u-boot/board/freescale/p1010rdb/ |
H A D | README.P1010RDB-PB | 37 PCB: 6-layer routing (4-layer signals, 2-layer power and ground)
|
H A D | README.P1010RDB-PA | 54 - 6-layer routing (4-layer signals, 2-layer power and ground)
|
/openbmc/linux/Documentation/sound/designs/ |
H A D | channel-mapping-api.rst | 41 As a ground design, each PCM substream may contain a control element
|
/openbmc/u-boot/arch/arm/dts/ |
H A D | rk3399-gru.dtsi | 523 * hooked to ground. Because we specified "cd-gpios" below dw_mmc 776 * In our case the official card detect is hooked to ground
|
/openbmc/linux/arch/arm64/boot/dts/rockchip/ |
H A D | rk3399-gru.dtsi | 542 * hooked to ground. Because we specified "cd-gpios" below dw_mmc 797 * In our case the official card detect is hooked to ground
|
/openbmc/linux/Documentation/input/devices/ |
H A D | joystick-parport.rst | 87 Ground is quite easy. On PC's parallel port the ground is on any of the 88 pins from pin 18 to pin 25. So use any pin of these you like for the ground::
|