1 /*
2 * MicroWire interface driver for OMAP
3 *
4 * Copyright 2003 MontaVista Software Inc. <source@mvista.com>
5 *
6 * Ported to 2.6 OMAP uwire interface.
7 * Copyright (C) 2004 Texas Instruments.
8 *
9 * Generalization patches by Juha Yrjola <juha.yrjola@nokia.com>
10 *
11 * Copyright (C) 2005 David Brownell (ported to 2.6 SPI interface)
12 * Copyright (C) 2006 Nokia
13 *
14 * Many updates by Imre Deak <imre.deak@nokia.com>
15 *
16 * This program is free software; you can redistribute it and/or modify it
17 * under the terms of the GNU General Public License as published by the
18 * Free Software Foundation; either version 2 of the License, or (at your
19 * option) any later version.
20 *
21 * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED
22 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
23 * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
24 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
25 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
26 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
27 * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
28 * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
29 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
30 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
31 */
32 #include <linux/kernel.h>
33 #include <linux/init.h>
34 #include <linux/delay.h>
35 #include <linux/platform_device.h>
36 #include <linux/interrupt.h>
37 #include <linux/err.h>
38 #include <linux/clk.h>
39 #include <linux/slab.h>
40 #include <linux/device.h>
41
42 #include <linux/spi/spi.h>
43 #include <linux/spi/spi_bitbang.h>
44 #include <linux/module.h>
45 #include <linux/io.h>
46
47 #include <asm/mach-types.h>
48 #include <linux/soc/ti/omap1-io.h>
49 #include <linux/soc/ti/omap1-soc.h>
50 #include <linux/soc/ti/omap1-mux.h>
51
52 /* FIXME address is now a platform device resource,
53 * and irqs should show there too...
54 */
55 #define UWIRE_BASE_PHYS 0xFFFB3000
56
57 /* uWire Registers: */
58 #define UWIRE_IO_SIZE 0x20
59 #define UWIRE_TDR 0x00
60 #define UWIRE_RDR 0x00
61 #define UWIRE_CSR 0x01
62 #define UWIRE_SR1 0x02
63 #define UWIRE_SR2 0x03
64 #define UWIRE_SR3 0x04
65 #define UWIRE_SR4 0x05
66 #define UWIRE_SR5 0x06
67
68 /* CSR bits */
69 #define RDRB (1 << 15)
70 #define CSRB (1 << 14)
71 #define START (1 << 13)
72 #define CS_CMD (1 << 12)
73
74 /* SR1 or SR2 bits */
75 #define UWIRE_READ_FALLING_EDGE 0x0001
76 #define UWIRE_READ_RISING_EDGE 0x0000
77 #define UWIRE_WRITE_FALLING_EDGE 0x0000
78 #define UWIRE_WRITE_RISING_EDGE 0x0002
79 #define UWIRE_CS_ACTIVE_LOW 0x0000
80 #define UWIRE_CS_ACTIVE_HIGH 0x0004
81 #define UWIRE_FREQ_DIV_2 0x0000
82 #define UWIRE_FREQ_DIV_4 0x0008
83 #define UWIRE_FREQ_DIV_8 0x0010
84 #define UWIRE_CHK_READY 0x0020
85 #define UWIRE_CLK_INVERTED 0x0040
86
87
88 struct uwire_spi {
89 struct spi_bitbang bitbang;
90 struct clk *ck;
91 };
92
93 struct uwire_state {
94 unsigned div1_idx;
95 };
96
97 /* REVISIT compile time constant for idx_shift? */
98 /*
99 * Or, put it in a structure which is used throughout the driver;
100 * that avoids having to issue two loads for each bit of static data.
101 */
102 static unsigned int uwire_idx_shift = 2;
103 static void __iomem *uwire_base;
104
uwire_write_reg(int idx,u16 val)105 static inline void uwire_write_reg(int idx, u16 val)
106 {
107 __raw_writew(val, uwire_base + (idx << uwire_idx_shift));
108 }
109
uwire_read_reg(int idx)110 static inline u16 uwire_read_reg(int idx)
111 {
112 return __raw_readw(uwire_base + (idx << uwire_idx_shift));
113 }
114
omap_uwire_configure_mode(u8 cs,unsigned long flags)115 static inline void omap_uwire_configure_mode(u8 cs, unsigned long flags)
116 {
117 u16 w, val = 0;
118 int shift, reg;
119
120 if (flags & UWIRE_CLK_INVERTED)
121 val ^= 0x03;
122 val = flags & 0x3f;
123 if (cs & 1)
124 shift = 6;
125 else
126 shift = 0;
127 if (cs <= 1)
128 reg = UWIRE_SR1;
129 else
130 reg = UWIRE_SR2;
131
132 w = uwire_read_reg(reg);
133 w &= ~(0x3f << shift);
134 w |= val << shift;
135 uwire_write_reg(reg, w);
136 }
137
wait_uwire_csr_flag(u16 mask,u16 val,int might_not_catch)138 static int wait_uwire_csr_flag(u16 mask, u16 val, int might_not_catch)
139 {
140 u16 w;
141 int c = 0;
142 unsigned long max_jiffies = jiffies + HZ;
143
144 for (;;) {
145 w = uwire_read_reg(UWIRE_CSR);
146 if ((w & mask) == val)
147 break;
148 if (time_after(jiffies, max_jiffies)) {
149 printk(KERN_ERR "%s: timeout. reg=%#06x "
150 "mask=%#06x val=%#06x\n",
151 __func__, w, mask, val);
152 return -1;
153 }
154 c++;
155 if (might_not_catch && c > 64)
156 break;
157 }
158 return 0;
159 }
160
uwire_set_clk1_div(int div1_idx)161 static void uwire_set_clk1_div(int div1_idx)
162 {
163 u16 w;
164
165 w = uwire_read_reg(UWIRE_SR3);
166 w &= ~(0x03 << 1);
167 w |= div1_idx << 1;
168 uwire_write_reg(UWIRE_SR3, w);
169 }
170
uwire_chipselect(struct spi_device * spi,int value)171 static void uwire_chipselect(struct spi_device *spi, int value)
172 {
173 struct uwire_state *ust = spi->controller_state;
174 u16 w;
175 int old_cs;
176
177
178 BUG_ON(wait_uwire_csr_flag(CSRB, 0, 0));
179
180 w = uwire_read_reg(UWIRE_CSR);
181 old_cs = (w >> 10) & 0x03;
182 if (value == BITBANG_CS_INACTIVE || old_cs != spi_get_chipselect(spi, 0)) {
183 /* Deselect this CS, or the previous CS */
184 w &= ~CS_CMD;
185 uwire_write_reg(UWIRE_CSR, w);
186 }
187 /* activate specfied chipselect */
188 if (value == BITBANG_CS_ACTIVE) {
189 uwire_set_clk1_div(ust->div1_idx);
190 /* invert clock? */
191 if (spi->mode & SPI_CPOL)
192 uwire_write_reg(UWIRE_SR4, 1);
193 else
194 uwire_write_reg(UWIRE_SR4, 0);
195
196 w = spi_get_chipselect(spi, 0) << 10;
197 w |= CS_CMD;
198 uwire_write_reg(UWIRE_CSR, w);
199 }
200 }
201
uwire_txrx(struct spi_device * spi,struct spi_transfer * t)202 static int uwire_txrx(struct spi_device *spi, struct spi_transfer *t)
203 {
204 unsigned len = t->len;
205 unsigned bits = t->bits_per_word;
206 unsigned bytes;
207 u16 val, w;
208 int status = 0;
209
210 if (!t->tx_buf && !t->rx_buf)
211 return 0;
212
213 w = spi_get_chipselect(spi, 0) << 10;
214 w |= CS_CMD;
215
216 if (t->tx_buf) {
217 const u8 *buf = t->tx_buf;
218
219 /* NOTE: DMA could be used for TX transfers */
220
221 /* write one or two bytes at a time */
222 while (len >= 1) {
223 /* tx bit 15 is first sent; we byteswap multibyte words
224 * (msb-first) on the way out from memory.
225 */
226 val = *buf++;
227 if (bits > 8) {
228 bytes = 2;
229 val |= *buf++ << 8;
230 } else
231 bytes = 1;
232 val <<= 16 - bits;
233
234 #ifdef VERBOSE
235 pr_debug("%s: write-%d =%04x\n",
236 dev_name(&spi->dev), bits, val);
237 #endif
238 if (wait_uwire_csr_flag(CSRB, 0, 0))
239 goto eio;
240
241 uwire_write_reg(UWIRE_TDR, val);
242
243 /* start write */
244 val = START | w | (bits << 5);
245
246 uwire_write_reg(UWIRE_CSR, val);
247 len -= bytes;
248
249 /* Wait till write actually starts.
250 * This is needed with MPU clock 60+ MHz.
251 * REVISIT: we may not have time to catch it...
252 */
253 if (wait_uwire_csr_flag(CSRB, CSRB, 1))
254 goto eio;
255
256 status += bytes;
257 }
258
259 /* REVISIT: save this for later to get more i/o overlap */
260 if (wait_uwire_csr_flag(CSRB, 0, 0))
261 goto eio;
262
263 } else if (t->rx_buf) {
264 u8 *buf = t->rx_buf;
265
266 /* read one or two bytes at a time */
267 while (len) {
268 if (bits > 8) {
269 bytes = 2;
270 } else
271 bytes = 1;
272
273 /* start read */
274 val = START | w | (bits << 0);
275 uwire_write_reg(UWIRE_CSR, val);
276 len -= bytes;
277
278 /* Wait till read actually starts */
279 (void) wait_uwire_csr_flag(CSRB, CSRB, 1);
280
281 if (wait_uwire_csr_flag(RDRB | CSRB,
282 RDRB, 0))
283 goto eio;
284
285 /* rx bit 0 is last received; multibyte words will
286 * be properly byteswapped on the way to memory.
287 */
288 val = uwire_read_reg(UWIRE_RDR);
289 val &= (1 << bits) - 1;
290 *buf++ = (u8) val;
291 if (bytes == 2)
292 *buf++ = val >> 8;
293 status += bytes;
294 #ifdef VERBOSE
295 pr_debug("%s: read-%d =%04x\n",
296 dev_name(&spi->dev), bits, val);
297 #endif
298
299 }
300 }
301 return status;
302 eio:
303 return -EIO;
304 }
305
uwire_setup_transfer(struct spi_device * spi,struct spi_transfer * t)306 static int uwire_setup_transfer(struct spi_device *spi, struct spi_transfer *t)
307 {
308 struct uwire_state *ust = spi->controller_state;
309 struct uwire_spi *uwire;
310 unsigned flags = 0;
311 unsigned hz;
312 unsigned long rate;
313 int div1_idx;
314 int div1;
315 int div2;
316 int status;
317
318 uwire = spi_master_get_devdata(spi->master);
319
320 /* mode 0..3, clock inverted separately;
321 * standard nCS signaling;
322 * don't treat DI=high as "not ready"
323 */
324 if (spi->mode & SPI_CS_HIGH)
325 flags |= UWIRE_CS_ACTIVE_HIGH;
326
327 if (spi->mode & SPI_CPOL)
328 flags |= UWIRE_CLK_INVERTED;
329
330 switch (spi->mode & SPI_MODE_X_MASK) {
331 case SPI_MODE_0:
332 case SPI_MODE_3:
333 flags |= UWIRE_WRITE_FALLING_EDGE | UWIRE_READ_RISING_EDGE;
334 break;
335 case SPI_MODE_1:
336 case SPI_MODE_2:
337 flags |= UWIRE_WRITE_RISING_EDGE | UWIRE_READ_FALLING_EDGE;
338 break;
339 }
340
341 /* assume it's already enabled */
342 rate = clk_get_rate(uwire->ck);
343
344 if (t != NULL)
345 hz = t->speed_hz;
346 else
347 hz = spi->max_speed_hz;
348
349 if (!hz) {
350 pr_debug("%s: zero speed?\n", dev_name(&spi->dev));
351 status = -EINVAL;
352 goto done;
353 }
354
355 /* F_INT = mpu_xor_clk / DIV1 */
356 for (div1_idx = 0; div1_idx < 4; div1_idx++) {
357 switch (div1_idx) {
358 case 0:
359 div1 = 2;
360 break;
361 case 1:
362 div1 = 4;
363 break;
364 case 2:
365 div1 = 7;
366 break;
367 default:
368 case 3:
369 div1 = 10;
370 break;
371 }
372 div2 = (rate / div1 + hz - 1) / hz;
373 if (div2 <= 8)
374 break;
375 }
376 if (div1_idx == 4) {
377 pr_debug("%s: lowest clock %ld, need %d\n",
378 dev_name(&spi->dev), rate / 10 / 8, hz);
379 status = -EDOM;
380 goto done;
381 }
382
383 /* we have to cache this and reset in uwire_chipselect as this is a
384 * global parameter and another uwire device can change it under
385 * us */
386 ust->div1_idx = div1_idx;
387 uwire_set_clk1_div(div1_idx);
388
389 rate /= div1;
390
391 switch (div2) {
392 case 0:
393 case 1:
394 case 2:
395 flags |= UWIRE_FREQ_DIV_2;
396 rate /= 2;
397 break;
398 case 3:
399 case 4:
400 flags |= UWIRE_FREQ_DIV_4;
401 rate /= 4;
402 break;
403 case 5:
404 case 6:
405 case 7:
406 case 8:
407 flags |= UWIRE_FREQ_DIV_8;
408 rate /= 8;
409 break;
410 }
411 omap_uwire_configure_mode(spi_get_chipselect(spi, 0), flags);
412 pr_debug("%s: uwire flags %02x, armxor %lu KHz, SCK %lu KHz\n",
413 __func__, flags,
414 clk_get_rate(uwire->ck) / 1000,
415 rate / 1000);
416 status = 0;
417 done:
418 return status;
419 }
420
uwire_setup(struct spi_device * spi)421 static int uwire_setup(struct spi_device *spi)
422 {
423 struct uwire_state *ust = spi->controller_state;
424 bool initial_setup = false;
425 int status;
426
427 if (ust == NULL) {
428 ust = kzalloc(sizeof(*ust), GFP_KERNEL);
429 if (ust == NULL)
430 return -ENOMEM;
431 spi->controller_state = ust;
432 initial_setup = true;
433 }
434
435 status = uwire_setup_transfer(spi, NULL);
436 if (status && initial_setup)
437 kfree(ust);
438
439 return status;
440 }
441
uwire_cleanup(struct spi_device * spi)442 static void uwire_cleanup(struct spi_device *spi)
443 {
444 kfree(spi->controller_state);
445 }
446
uwire_off(struct uwire_spi * uwire)447 static void uwire_off(struct uwire_spi *uwire)
448 {
449 uwire_write_reg(UWIRE_SR3, 0);
450 clk_disable_unprepare(uwire->ck);
451 spi_master_put(uwire->bitbang.master);
452 }
453
uwire_probe(struct platform_device * pdev)454 static int uwire_probe(struct platform_device *pdev)
455 {
456 struct spi_master *master;
457 struct uwire_spi *uwire;
458 int status;
459
460 master = spi_alloc_master(&pdev->dev, sizeof(*uwire));
461 if (!master)
462 return -ENODEV;
463
464 uwire = spi_master_get_devdata(master);
465
466 uwire_base = devm_ioremap(&pdev->dev, UWIRE_BASE_PHYS, UWIRE_IO_SIZE);
467 if (!uwire_base) {
468 dev_dbg(&pdev->dev, "can't ioremap UWIRE\n");
469 spi_master_put(master);
470 return -ENOMEM;
471 }
472
473 platform_set_drvdata(pdev, uwire);
474
475 uwire->ck = devm_clk_get(&pdev->dev, "fck");
476 if (IS_ERR(uwire->ck)) {
477 status = PTR_ERR(uwire->ck);
478 dev_dbg(&pdev->dev, "no functional clock?\n");
479 spi_master_put(master);
480 return status;
481 }
482 clk_prepare_enable(uwire->ck);
483
484 uwire_write_reg(UWIRE_SR3, 1);
485
486 /* the spi->mode bits understood by this driver: */
487 master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
488 master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 16);
489 master->flags = SPI_CONTROLLER_HALF_DUPLEX;
490
491 master->bus_num = 2; /* "official" */
492 master->num_chipselect = 4;
493 master->setup = uwire_setup;
494 master->cleanup = uwire_cleanup;
495
496 uwire->bitbang.master = master;
497 uwire->bitbang.chipselect = uwire_chipselect;
498 uwire->bitbang.setup_transfer = uwire_setup_transfer;
499 uwire->bitbang.txrx_bufs = uwire_txrx;
500
501 status = spi_bitbang_start(&uwire->bitbang);
502 if (status < 0) {
503 uwire_off(uwire);
504 }
505 return status;
506 }
507
uwire_remove(struct platform_device * pdev)508 static void uwire_remove(struct platform_device *pdev)
509 {
510 struct uwire_spi *uwire = platform_get_drvdata(pdev);
511
512 // FIXME remove all child devices, somewhere ...
513
514 spi_bitbang_stop(&uwire->bitbang);
515 uwire_off(uwire);
516 }
517
518 /* work with hotplug and coldplug */
519 MODULE_ALIAS("platform:omap_uwire");
520
521 static struct platform_driver uwire_driver = {
522 .driver = {
523 .name = "omap_uwire",
524 },
525 .probe = uwire_probe,
526 .remove_new = uwire_remove,
527 // suspend ... unuse ck
528 // resume ... use ck
529 };
530
omap_uwire_init(void)531 static int __init omap_uwire_init(void)
532 {
533 return platform_driver_register(&uwire_driver);
534 }
535
omap_uwire_exit(void)536 static void __exit omap_uwire_exit(void)
537 {
538 platform_driver_unregister(&uwire_driver);
539 }
540
541 subsys_initcall(omap_uwire_init);
542 module_exit(omap_uwire_exit);
543
544 MODULE_LICENSE("GPL");
545
546