| /openbmc/u-boot/net/ |
| H A D | link_local.c | 49 DISABLED enumerator
50 } state = DISABLED;
216 if (state == DISABLED) in link_local_receive_arp()
|
| /openbmc/linux/arch/sh/kernel/cpu/sh4a/ |
| H A D | setup-sh7366.c | 251 DISABLED, enumerator
334 { DISABLED, ENABLED, ENABLED, ENABLED, 0, 0, 0, SIU } },
375 .force_disable = DISABLED,
|
| H A D | setup-sh7343.c | 307 DISABLED, enumerator
397 { DISABLED, ENABLED, ENABLED, ENABLED, 0, 0, 0, SIU } },
436 .force_disable = DISABLED,
|
| H A D | setup-sh7722.c | 523 DISABLED, enumerator
611 { DISABLED, ENABLED, ENABLED, ENABLED, 0, 0, TWODG, SIU } },
652 .force_disable = DISABLED,
|
| H A D | setup-sh7723.c | 431 DISABLED, enumerator
636 .force_disable = DISABLED,
|
| H A D | setup-sh7724.c | 851 DISABLED, enumerator
1040 { DISABLED, ENABLED, ENABLED, ENABLED,
1090 .force_disable = DISABLED,
|
| /openbmc/qemu/include/hw/dma/ |
| H A D | xlnx-zdma.h | 40 DISABLED = 0, enumerator
|
| /openbmc/openbmc/meta-openembedded/meta-networking/recipes-connectivity/openfortivpn/ |
| H A D | openfortivpn_1.21.0.bb | 12 …] = "--with-resolvconf=${base_sbindir}/resolvconf --enable-resolvconf,--with-resolvconf=DISABLED,,"
|
| /openbmc/linux/drivers/pinctrl/ |
| H A D | pinctrl-k210.c | 323 K210_FUNC(RESV0, DISABLED),
324 K210_FUNC(RESV1, DISABLED),
325 K210_FUNC(RESV2, DISABLED),
326 K210_FUNC(RESV3, DISABLED),
327 K210_FUNC(RESV4, DISABLED),
328 K210_FUNC(RESV5, DISABLED),
425 K210_FUNC(CONSTANT, DISABLED),
|
| /openbmc/qemu/hw/dma/ |
| H A D | xlnx-zdma.c | 522 zdma_set_state(s, DISABLED); in zdma_process_descr()
542 zdma_set_state(s, DISABLED); in zdma_run()
581 } else if (s->state == DISABLED) { in zdma_ch_ctrlx_postw()
589 zdma_set_state(s, DISABLED); in zdma_ch_ctrlx_postw()
|
| /openbmc/linux/Documentation/admin-guide/ |
| H A D | pnp.rst | 73 DISABLED
75 - Notice the string "DISABLED". This means the device is not active.
|
| /openbmc/linux/Documentation/ABI/testing/ |
| H A D | sysfs-class-mei | 80 DISABLED
|
| /openbmc/linux/drivers/misc/mei/ |
| H A D | init.c | 26 MEI_DEV_STATE(DISABLED); in mei_dev_state_str()
|
| /openbmc/linux/Documentation/driver-api/soundwire/ |
| H A D | stream.rst | 249 | RELEASED |<----------+ DEPREPARED |<-------+ DISABLED |
260 does not e.g. check if a transition from DISABLED to ENABLED is valid
428 Bus implements below API for DISABLED state which needs to be called once
|
| /openbmc/openbmc/poky/meta/recipes-support/curl/ |
| H A D | curl_8.7.1.bb | 105 cat ${WORKDIR}/disable-tests >> ${S}/tests/data/DISABLED
|
| /openbmc/linux/arch/m68k/q40/ |
| H A D | README | 91 - 50 or 200 Hz - level 2, !!THIS CAN'T BE DISABLED!!
|
| /openbmc/linux/Documentation/trace/ |
| H A D | kprobes.rst | 751 such probes are marked with [DISABLED]. If the probe is optimized, it is
762 [DISABLED]) will be not enabled if you turn ON all kprobes by this knob.
|
| /openbmc/linux/Documentation/networking/ |
| H A D | switchdev.rst | 300 DISABLED, no packets should pass, but if port moves to BLOCKED, then STP BPDUs
|