1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * Copyright (c) 2022, 2023 Jianhua Lu <lujianhua000@gmail.com> 4 */ 5 6#include <dt-bindings/arm/qcom,ids.h> 7#include <dt-bindings/phy/phy.h> 8#include <dt-bindings/regulator/qcom,rpmh-regulator.h> 9#include "sm8250.dtsi" 10#include "pm8150.dtsi" 11#include "pm8150b.dtsi" 12#include "pm8150l.dtsi" 13#include "pm8009.dtsi" 14 15/* 16 * Delete following upstream (sm8250.dtsi) reserved 17 * memory mappings which are different on this device. 18 */ 19/delete-node/ &adsp_mem; 20/delete-node/ &cdsp_secure_heap; 21/delete-node/ &slpi_mem; 22/delete-node/ &spss_mem; 23/delete-node/ &xbl_aop_mem; 24 25/ { 26 classis-type = "tablet"; 27 28 /* required for bootloader to select correct board */ 29 qcom,msm-id = <QCOM_ID_SM8250 0x20001>; /* SM8250 v2.1 */ 30 qcom,board-id = <0x10008 0>; 31 32 chosen { 33 #address-cells = <2>; 34 #size-cells = <2>; 35 ranges; 36 37 framebuffer: framebuffer@9c000000 { 38 compatible = "simple-framebuffer"; 39 reg = <0x0 0x9c000000 0x0 0x2300000>; 40 width = <1600>; 41 height = <2560>; 42 stride = <(1600 * 4)>; 43 format = "a8r8g8b8"; 44 }; 45 }; 46 47 battery_l: battery-l { 48 compatible = "simple-battery"; 49 voltage-min-design-microvolt = <3870000>; 50 energy-full-design-microwatt-hours = <16600000>; 51 charge-full-design-microamp-hours = <4300000>; 52 }; 53 54 battery_r: battery-r { 55 compatible = "simple-battery"; 56 voltage-min-design-microvolt = <3870000>; 57 energy-full-design-microwatt-hours = <16600000>; 58 charge-full-design-microamp-hours = <4300000>; 59 }; 60 61 bl_vddpos_5p5: bl-vddpos-regulator { 62 compatible = "regulator-fixed"; 63 regulator-name = "bl_vddpos_5p5"; 64 regulator-min-microvolt = <5500000>; 65 regulator-max-microvolt = <5500000>; 66 regulator-enable-ramp-delay = <233>; 67 gpio = <&tlmm 130 GPIO_ACTIVE_HIGH>; 68 enable-active-high; 69 regulator-boot-on; 70 }; 71 72 bl_vddneg_5p5: bl-vddneg-regulator { 73 compatible = "regulator-fixed"; 74 regulator-name = "bl_vddneg_5p5"; 75 regulator-min-microvolt = <5500000>; 76 regulator-max-microvolt = <5500000>; 77 regulator-enable-ramp-delay = <233>; 78 gpio = <&tlmm 131 GPIO_ACTIVE_HIGH>; 79 enable-active-high; 80 regulator-boot-on; 81 }; 82 83 gpio_keys: gpio-keys { 84 compatible = "gpio-keys"; 85 86 pinctrl-names = "default"; 87 pinctrl-0 = <&vol_up_n>; 88 89 key-vol-up { 90 label = "Volume Up"; 91 gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>; 92 linux,code = <KEY_VOLUMEUP>; 93 debounce-interval = <15>; 94 linux,can-disable; 95 wakeup-source; 96 }; 97 }; 98 99 vph_pwr: vph-pwr-regulator { 100 compatible = "regulator-fixed"; 101 regulator-name = "vph_pwr"; 102 regulator-min-microvolt = <3700000>; 103 regulator-max-microvolt = <3700000>; 104 }; 105 106 /* S6c is really ebi.lvl but it's there for supply map completeness sake. */ 107 vreg_s6c_0p88: smpc6-regulator { 108 compatible = "regulator-fixed"; 109 regulator-name = "vreg_s6c_0p88"; 110 regulator-min-microvolt = <880000>; 111 regulator-max-microvolt = <880000>; 112 regulator-always-on; 113 vin-supply = <&vph_pwr>; 114 }; 115 116 reserved-memory { 117 xbl_aop_mem: xbl-aop@80700000 { 118 reg = <0x0 0x80600000 0x0 0x260000>; 119 no-map; 120 }; 121 122 slpi_mem: slpi@88c00000 { 123 reg = <0x0 0x88c00000 0x0 0x2f00000>; 124 no-map; 125 }; 126 127 adsp_mem: adsp@8bb00000 { 128 reg = <0x0 0x8bb00000 0x0 0x2500000>; 129 no-map; 130 }; 131 132 spss_mem: spss@8e000000 { 133 reg = <0x0 0x8e000000 0x0 0x100000>; 134 no-map; 135 }; 136 137 cdsp_secure_heap: cdsp-secure-heap@8e100000 { 138 reg = <0x0 0x8e100000 0x0 0x4600000>; 139 no-map; 140 }; 141 142 cont_splash_mem: cont-splash@9c000000 { 143 reg = <0x0 0x9c000000 0x0 0x2300000>; 144 no-map; 145 }; 146 147 ramoops@b0000000 { 148 compatible = "ramoops"; 149 reg = <0x0 0xb0000000 0x0 0x400000>; 150 record-size = <0x1000>; 151 console-size = <0x200000>; 152 ecc-size = <16>; 153 no-map; 154 }; 155 }; 156}; 157 158&adsp { 159 firmware-name = "qcom/sm8250/xiaomi/elish/adsp.mbn"; 160 status = "okay"; 161}; 162 163&apps_rsc { 164 regulators-0 { 165 compatible = "qcom,pm8150-rpmh-regulators"; 166 qcom,pmic-id = "a"; 167 168 vdd-s1-supply = <&vph_pwr>; 169 vdd-s2-supply = <&vph_pwr>; 170 vdd-s3-supply = <&vph_pwr>; 171 vdd-s4-supply = <&vph_pwr>; 172 vdd-s5-supply = <&vph_pwr>; 173 vdd-s6-supply = <&vph_pwr>; 174 vdd-s7-supply = <&vph_pwr>; 175 vdd-s8-supply = <&vph_pwr>; 176 vdd-s9-supply = <&vph_pwr>; 177 vdd-s10-supply = <&vph_pwr>; 178 vdd-l1-l8-l11-supply = <&vreg_s6c_0p88>; 179 vdd-l2-l10-supply = <&vreg_bob>; 180 vdd-l3-l4-l5-l18-supply = <&vreg_s6a_0p95>; 181 vdd-l6-l9-supply = <&vreg_s8c_1p35>; 182 vdd-l7-l12-l14-l15-supply = <&vreg_s5a_1p9>; 183 vdd-l13-l16-l17-supply = <&vreg_bob>; 184 185 /* (S1+S2+S3) - cx.lvl (ARC) */ 186 187 vreg_s4a_1p8: smps4 { 188 regulator-name = "vreg_s4a_1p8"; 189 regulator-min-microvolt = <1800000>; 190 regulator-max-microvolt = <1920000>; 191 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 192 regulator-allow-set-load; 193 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM 194 RPMH_REGULATOR_MODE_HPM>; 195 }; 196 197 vreg_s5a_1p9: smps5 { 198 regulator-name = "vreg_s5a_1p9"; 199 regulator-min-microvolt = <1900000>; 200 regulator-max-microvolt = <2040000>; 201 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 202 }; 203 204 vreg_s6a_0p95: smps6 { 205 regulator-name = "vreg_s6a_0p95"; 206 regulator-min-microvolt = <950000>; 207 regulator-max-microvolt = <1128000>; 208 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 209 }; 210 211 vreg_l2a_3p1: ldo2 { 212 regulator-name = "vreg_l2a_3p1"; 213 regulator-min-microvolt = <3072000>; 214 regulator-max-microvolt = <3072000>; 215 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 216 }; 217 218 vreg_l3a_0p9: ldo3 { 219 regulator-name = "vreg_l3a_0p9"; 220 regulator-min-microvolt = <928000>; 221 regulator-max-microvolt = <932000>; 222 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 223 }; 224 225 /* L4 - lmx.lvl (ARC) */ 226 227 vreg_l5a_0p88: ldo5 { 228 regulator-name = "vreg_l5a_0p88"; 229 regulator-min-microvolt = <880000>; 230 regulator-max-microvolt = <880000>; 231 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 232 }; 233 234 vreg_l6a_1p2: ldo6 { 235 regulator-name = "vreg_l6a_1p2"; 236 regulator-min-microvolt = <1200000>; 237 regulator-max-microvolt = <1200000>; 238 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 239 regulator-allow-set-load; 240 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM 241 RPMH_REGULATOR_MODE_HPM>; 242 }; 243 244 /* L7 is unused. */ 245 246 vreg_l9a_1p2: ldo9 { 247 regulator-name = "vreg_l9a_1p2"; 248 regulator-min-microvolt = <1200000>; 249 regulator-max-microvolt = <1200000>; 250 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 251 }; 252 253 /* L10 is unused, L11 - lcx.lvl (ARC) */ 254 255 vreg_l12a_1p8: ldo12 { 256 regulator-name = "vreg_l12a_1p8"; 257 regulator-min-microvolt = <1800000>; 258 regulator-max-microvolt = <1800000>; 259 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 260 }; 261 262 /* L13 is unused. */ 263 264 vreg_l14a_1p88: ldo14 { 265 regulator-name = "vreg_l14a_1p88"; 266 regulator-min-microvolt = <1880000>; 267 regulator-max-microvolt = <1880000>; 268 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 269 }; 270 271 /* L15 & L16 are unused. */ 272 273 vreg_l17a_3p0: ldo17 { 274 regulator-name = "vreg_l17a_3p0"; 275 regulator-min-microvolt = <2496000>; 276 regulator-max-microvolt = <3008000>; 277 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 278 regulator-allow-set-load; 279 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM 280 RPMH_REGULATOR_MODE_HPM>; 281 }; 282 283 vreg_l18a_0p9: ldo18 { 284 regulator-name = "vreg_l18a_0p9"; 285 regulator-min-microvolt = <800000>; 286 regulator-max-microvolt = <920000>; 287 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 288 }; 289 }; 290 291 /* 292 * Remaining regulators that are not yet supported: 293 * OLEDB: 4925000-8100000 294 * ab: 4600000-6100000 295 * ibb: 800000-5400000 296 */ 297 regulators-1 { 298 compatible = "qcom,pm8150l-rpmh-regulators"; 299 qcom,pmic-id = "c"; 300 301 vdd-s1-supply = <&vph_pwr>; 302 vdd-s2-supply = <&vph_pwr>; 303 vdd-s3-supply = <&vph_pwr>; 304 vdd-s4-supply = <&vph_pwr>; 305 vdd-s5-supply = <&vph_pwr>; 306 vdd-s6-supply = <&vph_pwr>; 307 vdd-s7-supply = <&vph_pwr>; 308 vdd-s8-supply = <&vph_pwr>; 309 vdd-l1-l8-supply = <&vreg_s4a_1p8>; 310 vdd-l2-l3-supply = <&vreg_s8c_1p35>; 311 vdd-l4-l5-l6-supply = <&vreg_bob>; 312 vdd-l7-l11-supply = <&vreg_bob>; 313 vdd-l9-l10-supply = <&vreg_bob>; 314 vdd-bob-supply = <&vph_pwr>; 315 316 vreg_bob: bob { 317 regulator-name = "vreg_bob"; 318 regulator-min-microvolt = <3350000>; 319 regulator-max-microvolt = <3960000>; 320 regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; 321 }; 322 323 /* 324 * S1-S6 are ARCs: 325 * (S1+S2) - gfx.lvl, 326 * S3 - mx.lvl, 327 * (S4+S5) - mmcx.lvl, 328 * S6 - ebi.lvl 329 */ 330 331 vreg_s7c_0p35: smps7 { 332 regulator-name = "vreg_s7c_0p35"; 333 regulator-min-microvolt = <348000>; 334 regulator-max-microvolt = <1000000>; 335 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 336 }; 337 338 vreg_s8c_1p35: smps8 { 339 regulator-name = "vreg_s8c_1p35"; 340 regulator-min-microvolt = <1350000>; 341 regulator-max-microvolt = <1400000>; 342 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 343 }; 344 345 vreg_l1c_1p8: ldo1 { 346 regulator-name = "vreg_l1c_1p8"; 347 regulator-min-microvolt = <1800000>; 348 regulator-max-microvolt = <1800000>; 349 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 350 }; 351 352 /* L2-4 are unused. */ 353 354 vreg_l5c_1p8: ldo5 { 355 regulator-name = "vreg_l5c_1p8"; 356 regulator-min-microvolt = <1800000>; 357 regulator-max-microvolt = <2800000>; 358 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 359 }; 360 361 vreg_l6c_2p9: ldo6 { 362 regulator-name = "vreg_l6c_2p9"; 363 regulator-min-microvolt = <1800000>; 364 regulator-max-microvolt = <2960000>; 365 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 366 regulator-allow-set-load; 367 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM 368 RPMH_REGULATOR_MODE_HPM>; 369 }; 370 371 vreg_l7c_2p85: ldo7 { 372 regulator-name = "vreg_l7c_2p85"; 373 regulator-min-microvolt = <2856000>; 374 regulator-max-microvolt = <3104000>; 375 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 376 }; 377 378 vreg_l8c_1p8: ldo8 { 379 regulator-name = "vreg_l8c_1p8"; 380 regulator-min-microvolt = <1800000>; 381 regulator-max-microvolt = <1800000>; 382 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 383 }; 384 385 vreg_l9c_2p9: ldo9 { 386 regulator-name = "vreg_l9c_2p9"; 387 regulator-min-microvolt = <2704000>; 388 regulator-max-microvolt = <2960000>; 389 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 390 regulator-allow-set-load; 391 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM 392 RPMH_REGULATOR_MODE_HPM>; 393 }; 394 395 vreg_l10c_3p3: ldo10 { 396 regulator-name = "vreg_l10c_3p3"; 397 regulator-min-microvolt = <3296000>; 398 regulator-max-microvolt = <3296000>; 399 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 400 }; 401 402 vreg_l11c_3p0: ldo11 { 403 regulator-name = "vreg_l11c_3p0"; 404 regulator-min-microvolt = <3000000>; 405 regulator-max-microvolt = <3000000>; 406 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 407 }; 408 }; 409 410 regulators-2 { 411 compatible = "qcom,pm8009-rpmh-regulators"; 412 qcom,pmic-id = "f"; 413 414 vdd-s1-supply = <&vph_pwr>; 415 vdd-s2-supply = <&vreg_bob>; 416 vdd-l2-supply = <&vreg_s8c_1p35>; 417 vdd-l5-l6-supply = <&vreg_bob>; 418 vdd-l7-supply = <&vreg_s4a_1p8>; 419 420 vreg_s1f_1p2: smps1 { 421 regulator-name = "vreg_s1f_1p2"; 422 regulator-min-microvolt = <1200000>; 423 regulator-max-microvolt = <1200000>; 424 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 425 }; 426 427 vreg_s2f_0p5: smps2 { 428 regulator-name = "vreg_s2f_0p5"; 429 regulator-min-microvolt = <512000>; 430 regulator-max-microvolt = <1100000>; 431 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 432 }; 433 434 /* L1 is unused. */ 435 436 vreg_l2f_1p3: ldo2 { 437 regulator-name = "vreg_l2f_1p3"; 438 regulator-min-microvolt = <1304000>; 439 regulator-max-microvolt = <1304000>; 440 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 441 }; 442 443 /* L3 & L4 are unused. */ 444 445 vreg_l5f_2p8: ldo5 { 446 regulator-name = "vreg_l5f_2p85"; 447 regulator-min-microvolt = <2800000>; 448 regulator-max-microvolt = <2800000>; 449 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 450 }; 451 452 vreg_l6f_2p8: ldo6 { 453 regulator-name = "vreg_l6f_2p8"; 454 regulator-min-microvolt = <2800000>; 455 regulator-max-microvolt = <2800000>; 456 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 457 }; 458 459 vreg_l7f_1p8: ldo7 { 460 regulator-name = "vreg_l7f_1p8"; 461 regulator-min-microvolt = <1800000>; 462 regulator-max-microvolt = <1800000>; 463 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 464 }; 465 }; 466}; 467 468&cdsp { 469 firmware-name = "qcom/sm8250/xiaomi/elish/cdsp.mbn"; 470 status = "okay"; 471}; 472 473&gmu { 474 status = "okay"; 475}; 476 477&gpi_dma0 { 478 status = "okay"; 479}; 480 481&gpi_dma1 { 482 status = "okay"; 483}; 484 485&gpi_dma2 { 486 status = "okay"; 487}; 488 489&gpu { 490 status = "okay"; 491 492 zap-shader { 493 memory-region = <&gpu_mem>; 494 firmware-name = "qcom/sm8250/xiaomi/elish/a650_zap.mbn"; 495 }; 496}; 497 498&i2c0 { 499 clock-frequency = <400000>; 500 status = "okay"; 501 502 fuel-gauge@55 { 503 compatible = "ti,bq27z561"; 504 reg = <0x55>; 505 monitored-battery = <&battery_r>; 506 }; 507}; 508 509&i2c11 { 510 clock-frequency = <400000>; 511 status = "okay"; 512 513 backlight: backlight@11 { 514 compatible = "kinetic,ktz8866"; 515 reg = <0x11>; 516 vddpos-supply = <&bl_vddpos_5p5>; 517 vddneg-supply = <&bl_vddneg_5p5>; 518 enable-gpios = <&tlmm 139 GPIO_ACTIVE_HIGH>; 519 current-num-sinks = <5>; 520 kinetic,current-ramp-delay-ms = <128>; 521 kinetic,led-enable-ramp-delay-ms = <1>; 522 kinetic,enable-lcd-bias; 523 }; 524}; 525 526&i2c13 { 527 clock-frequency = <400000>; 528 status = "okay"; 529 530 fuel-gauge@55 { 531 compatible = "ti,bq27z561"; 532 reg = <0x55>; 533 monitored-battery = <&battery_l>; 534 }; 535}; 536 537&mdss { 538 status = "okay"; 539}; 540 541&mdss_dsi0 { 542 vdda-supply = <&vreg_l9a_1p2>; 543 qcom,dual-dsi-mode; 544 qcom,sync-dual-dsi; 545 qcom,master-dsi; 546 status = "okay"; 547 548 display_panel: panel@0 { 549 reg = <0>; 550 vddio-supply = <&vreg_l14a_1p88>; 551 reset-gpios = <&tlmm 75 GPIO_ACTIVE_LOW>; 552 backlight = <&backlight>; 553 554 status = "disabled"; 555 556 ports { 557 #address-cells = <1>; 558 #size-cells = <0>; 559 560 port@0 { 561 reg = <0>; 562 563 panel_in_0: endpoint { 564 remote-endpoint = <&mdss_dsi0_out>; 565 }; 566 }; 567 568 port@1 { 569 reg = <1>; 570 571 panel_in_1: endpoint { 572 remote-endpoint = <&mdss_dsi1_out>; 573 }; 574 }; 575 }; 576 }; 577}; 578 579&mdss_dsi0_out { 580 data-lanes = <0 1 2>; 581 remote-endpoint = <&panel_in_0>; 582}; 583 584&mdss_dsi0_phy { 585 vdds-supply = <&vreg_l5a_0p88>; 586 phy-type = <PHY_TYPE_CPHY>; 587 status = "okay"; 588}; 589 590&mdss_dsi1 { 591 vdda-supply = <&vreg_l9a_1p2>; 592 qcom,dual-dsi-mode; 593 qcom,sync-dual-dsi; 594 /* DSI1 is slave, so use DSI0 clocks */ 595 assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>; 596 status = "okay"; 597}; 598 599&mdss_dsi1_out { 600 data-lanes = <0 1 2>; 601 remote-endpoint = <&panel_in_1>; 602}; 603 604&mdss_dsi1_phy { 605 vdds-supply = <&vreg_l5a_0p88>; 606 phy-type = <PHY_TYPE_CPHY>; 607 status = "okay"; 608}; 609 610&pcie0 { 611 status = "okay"; 612}; 613 614&pcie0_phy { 615 vdda-phy-supply = <&vreg_l5a_0p88>; 616 vdda-pll-supply = <&vreg_l9a_1p2>; 617 status = "okay"; 618}; 619 620&pm8150_gpios { 621 vol_up_n: vol-up-n-state { 622 pins = "gpio6"; 623 function = "normal"; 624 power-source = <1>; 625 input-enable; 626 bias-pull-up; 627 }; 628}; 629 630&pon_pwrkey { 631 status = "okay"; 632}; 633 634&pon_resin { 635 linux,code = <KEY_VOLUMEDOWN>; 636 status = "okay"; 637}; 638 639&qupv3_id_0 { 640 status = "okay"; 641}; 642 643&qupv3_id_1 { 644 status = "okay"; 645}; 646 647&qupv3_id_2 { 648 status = "okay"; 649}; 650 651&slpi { 652 firmware-name = "qcom/sm8250/xiaomi/elish/slpi.mbn"; 653 status = "okay"; 654}; 655 656&tlmm { 657 gpio-reserved-ranges = <40 4>; 658}; 659 660&usb_1 { 661 /* USB 2.0 only */ 662 qcom,select-utmi-as-pipe-clk; 663 status = "okay"; 664}; 665 666&usb_1_dwc3 { 667 dr_mode = "peripheral"; 668 maximum-speed = "high-speed"; 669 /* Remove USB3 phy */ 670 phys = <&usb_1_hsphy>; 671 phy-names = "usb2-phy"; 672}; 673 674&usb_1_hsphy { 675 vdda-pll-supply = <&vreg_l5a_0p88>; 676 vdda18-supply = <&vreg_l12a_1p8>; 677 vdda33-supply = <&vreg_l2a_3p1>; 678 status = "okay"; 679}; 680 681&ufs_mem_hc { 682 vcc-supply = <&vreg_l17a_3p0>; 683 vcc-max-microamp = <800000>; 684 vccq-supply = <&vreg_l6a_1p2>; 685 vccq-max-microamp = <800000>; 686 vccq2-supply = <&vreg_s4a_1p8>; 687 vccq2-max-microamp = <800000>; 688 status = "okay"; 689}; 690 691&ufs_mem_phy { 692 vdda-phy-supply = <&vreg_l5a_0p88>; 693 vdda-pll-supply = <&vreg_l9a_1p2>; 694 status = "okay"; 695}; 696 697&venus { 698 firmware-name = "qcom/sm8250/xiaomi/elish/venus.mbn"; 699 status = "okay"; 700}; 701