1// SPDX-License-Identifier: GPL-2.0-only OR BSD-3-Clause 2 3#include <dt-bindings/spmi/spmi.h> 4#include <dt-bindings/iio/qcom,spmi-vadc.h> 5 6&spmi_bus { 7 pmic@0 { 8 compatible = "qcom,pmp8074", "qcom,spmi-pmic"; 9 reg = <0x0 SPMI_USID>; 10 #address-cells = <1>; 11 #size-cells = <0>; 12 13 pmp8074_adc: adc@3100 { 14 compatible = "qcom,spmi-adc-rev2"; 15 reg = <0x3100>; 16 interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; 17 #address-cells = <1>; 18 #size-cells = <0>; 19 #io-channel-cells = <1>; 20 21 channel@0 { 22 reg = <ADC5_REF_GND>; 23 qcom,pre-scaling = <1 1>; 24 label = "ref_gnd"; 25 }; 26 27 channel@1 { 28 reg = <ADC5_1P25VREF>; 29 qcom,pre-scaling = <1 1>; 30 label = "vref_1p25"; 31 }; 32 33 channel@2 { 34 reg = <ADC5_VREF_VADC>; 35 qcom,pre-scaling = <1 1>; 36 label = "vref_vadc"; 37 }; 38 39 channel@6 { 40 reg = <ADC5_DIE_TEMP>; 41 qcom,pre-scaling = <1 1>; 42 label = "pmic_die"; 43 }; 44 45 channel@76 { 46 reg = <ADC5_XO_THERM_100K_PU>; 47 qcom,ratiometric; 48 qcom,hw-settle-time = <200>; 49 qcom,pre-scaling = <1 1>; 50 label = "xo_therm"; 51 }; 52 53 channel@77 { 54 reg = <ADC5_AMUX_THM1_100K_PU>; 55 qcom,ratiometric; 56 qcom,hw-settle-time = <200>; 57 qcom,pre-scaling = <1 1>; 58 label = "pa_therm1"; 59 }; 60 61 channel@78 { 62 reg = <ADC5_AMUX_THM2_100K_PU>; 63 qcom,ratiometric; 64 qcom,hw-settle-time = <200>; 65 qcom,pre-scaling = <1 1>; 66 label = "pa_therm2"; 67 }; 68 69 channel@79 { 70 reg = <ADC5_AMUX_THM3_100K_PU>; 71 qcom,ratiometric; 72 qcom,hw-settle-time = <200>; 73 qcom,pre-scaling = <1 1>; 74 label = "pa_therm3"; 75 }; 76 77 channel@131 { 78 reg = <ADC5_VPH_PWR>; 79 qcom,pre-scaling = <1 3>; 80 label = "vph_pwr"; 81 }; 82 }; 83 84 pmp8074_rtc: rtc@6000 { 85 compatible = "qcom,pm8941-rtc"; 86 reg = <0x6000>, <0x6100>; 87 reg-names = "rtc", "alarm"; 88 interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; 89 allow-set-time; 90 status = "disabled"; 91 }; 92 93 pmp8074_gpios: gpio@c000 { 94 compatible = "qcom,pmp8074-gpio", "qcom,spmi-gpio"; 95 reg = <0xc000>; 96 gpio-controller; 97 #gpio-cells = <2>; 98 gpio-ranges = <&pmp8074_gpios 0 0 12>; 99 interrupt-controller; 100 #interrupt-cells = <2>; 101 }; 102 }; 103 104 pmic@1 { 105 compatible = "qcom,pmp8074", "qcom,spmi-pmic"; 106 reg = <0x1 SPMI_USID>; 107 108 regulators { 109 compatible = "qcom,pmp8074-regulators"; 110 111 s3: s3 { 112 regulator-name = "vdd_s3"; 113 regulator-min-microvolt = <592000>; 114 regulator-max-microvolt = <1064000>; 115 regulator-always-on; 116 regulator-boot-on; 117 }; 118 119 s4: s4 { 120 regulator-name = "vdd_s4"; 121 regulator-min-microvolt = <712000>; 122 regulator-max-microvolt = <992000>; 123 regulator-always-on; 124 regulator-boot-on; 125 }; 126 127 l11: l11 { 128 regulator-name = "l11"; 129 regulator-min-microvolt = <1800000>; 130 regulator-max-microvolt = <3300000>; 131 }; 132 }; 133 }; 134}; 135