1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Support for CompuLab CM-T3530
4 */
5/dts-v1/;
6
7#include "omap34xx.dtsi"
8#include "omap3-cm-t3x30.dtsi"
9
10/ {
11	model = "CompuLab CM-T3530";
12	compatible = "compulab,omap3-cm-t3530", "ti,omap3430", "ti,omap34xx", "ti,omap3";
13
14	/* Regulator to trigger the reset signal of the Wifi module */
15	mmc2_sdio_reset: regulator-mmc2-sdio-reset {
16		compatible = "regulator-fixed";
17		regulator-name = "regulator-mmc2-sdio-reset";
18		regulator-min-microvolt = <3300000>;
19		regulator-max-microvolt = <3300000>;
20		gpio = <&twl_gpio 2 GPIO_ACTIVE_HIGH>;
21		enable-active-high;
22	};
23};
24
25&omap3_pmx_core {
26	mmc2_pins: mmc2-pins {
27		pinctrl-single,pins = <
28			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_clk.sdmmc2_clk */
29			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_cmd.sdmmc2_cmd */
30			OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat0.sdmmc2_dat0 */
31			OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat1.sdmmc2_dat1 */
32			OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat2.sdmmc2_dat2 */
33			OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0)		/* sdmmc2_dat3.sdmmc2_dat3 */
34			OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT | MUX_MODE1)		/* sdmmc2_dat4.sdmmc2_dir_dat0 */
35			OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1)		/* sdmmc2_dat5.sdmmc2_dir_dat1 */
36			OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE1)		/* sdmmc2_dat6.sdmmc2_dir_cmd */
37			OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE1)		/* sdmmc2_dat7.sdmmc2_clkin */
38		>;
39	};
40};
41
42&mmc2 {
43	pinctrl-names = "default";
44	pinctrl-0 = <&mmc2_pins>;
45	vmmc-supply = <&mmc2_sdio_reset>;
46	non-removable;
47	bus-width = <4>;
48	cap-power-off-card;
49};
50
51&dss {
52	status = "okay";
53
54	pinctrl-names = "default";
55	pinctrl-0 = <
56		&dss_dpi_pins_common
57		&dss_dpi_pins_cm_t35x
58	>;
59};
60
61