1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright 2017 NXP 4 * Copyright (C) 2014 Freescale Semiconductor 5 */ 6 7 #ifndef __LS2_COMMON_H 8 #define __LS2_COMMON_H 9 10 #define CONFIG_REMAKE_ELF 11 #define CONFIG_GICV3 12 13 #include <asm/arch/stream_id_lsch3.h> 14 #include <asm/arch/config.h> 15 16 /* Link Definitions */ 17 #ifdef CONFIG_TFABOOT 18 #define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE 19 #else 20 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0) 21 #endif 22 23 /* We need architecture specific misc initializations */ 24 25 /* Link Definitions */ 26 #ifndef CONFIG_TFABOOT 27 #ifndef CONFIG_QSPI_BOOT 28 #else 29 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 30 #define CONFIG_ENV_OFFSET 0x300000 /* 3MB */ 31 #define CONFIG_ENV_SECT_SIZE 0x40000 32 #endif 33 #endif 34 35 #define CONFIG_SKIP_LOWLEVEL_INIT 36 37 #ifndef CONFIG_SYS_FSL_DDR4 38 #define CONFIG_SYS_DDR_RAW_TIMING 39 #endif 40 41 #define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */ 42 43 #define CONFIG_VERY_BIG_RAM 44 #define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL 45 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0 46 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 47 #define CONFIG_SYS_DDR_BLOCK2_BASE 0x8080000000ULL 48 #define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 2 49 50 /* 51 * SMP Definitinos 52 */ 53 #define CPU_RELEASE_ADDR secondary_boot_func 54 55 #define CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS 56 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR 57 #define CONFIG_SYS_DP_DDR_BASE 0x6000000000ULL 58 /* 59 * DDR controller use 0 as the base address for binding. 60 * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access. 61 */ 62 #define CONFIG_SYS_DP_DDR_BASE_PHY 0 63 #define CONFIG_DP_DDR_CTRL 2 64 #define CONFIG_DP_DDR_NUM_CTRLS 1 65 #endif 66 67 /* Generic Timer Definitions */ 68 /* 69 * This is not an accurate number. It is used in start.S. The frequency 70 * will be udpated later when get_bus_freq(0) is available. 71 */ 72 #define COUNTER_FREQUENCY 25000000 /* 25MHz */ 73 74 /* Size of malloc() pool */ 75 #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2048 * 1024) 76 77 /* I2C */ 78 #define CONFIG_SYS_I2C 79 80 /* Serial Port */ 81 #define CONFIG_SYS_NS16550_SERIAL 82 #define CONFIG_SYS_NS16550_REG_SIZE 1 83 #define CONFIG_SYS_NS16550_CLK (get_serial_clock()) 84 85 #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } 86 87 /* IFC */ 88 #define CONFIG_FSL_IFC 89 90 /* 91 * During booting, IFC is mapped at the region of 0x30000000. 92 * But this region is limited to 256MB. To accommodate NOR, promjet 93 * and FPGA. This region is divided as below: 94 * 0x30000000 - 0x37ffffff : 128MB : NOR flash 95 * 0x38000000 - 0x3BFFFFFF : 64MB : Promjet 96 * 0x3C000000 - 0x40000000 : 64MB : FPGA etc 97 * 98 * To accommodate bigger NOR flash and other devices, we will map IFC 99 * chip selects to as below: 100 * 0x5_1000_0000..0x5_1fff_ffff Memory Hole 101 * 0x5_2000_0000..0x5_3fff_ffff IFC CSx (FPGA, NAND and others 512MB) 102 * 0x5_4000_0000..0x5_7fff_ffff ASIC or others 1GB 103 * 0x5_8000_0000..0x5_bfff_ffff IFC CS0 1GB (NOR/Promjet) 104 * 0x5_C000_0000..0x5_ffff_ffff IFC CS1 1GB (NOR/Promjet) 105 * 106 * For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation. 107 * CONFIG_SYS_FLASH_BASE has the final address (core view) 108 * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view) 109 * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address 110 * CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting 111 */ 112 113 #define CONFIG_SYS_FLASH_BASE 0x580000000ULL 114 #define CONFIG_SYS_FLASH_BASE_PHYS 0x80000000 115 #define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000 116 117 #define CONFIG_SYS_FLASH1_BASE_PHYS 0xC0000000 118 #define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY 0x8000000 119 120 #ifndef __ASSEMBLY__ 121 unsigned long long get_qixis_addr(void); 122 #endif 123 #define QIXIS_BASE get_qixis_addr() 124 #define QIXIS_BASE_PHYS 0x20000000 125 #define QIXIS_BASE_PHYS_EARLY 0xC000000 126 #define QIXIS_STAT_PRES1 0xb 127 #define QIXIS_SDID_MASK 0x07 128 #define QIXIS_ESDHC_NO_ADAPTER 0x7 129 130 #define CONFIG_SYS_NAND_BASE 0x530000000ULL 131 #define CONFIG_SYS_NAND_BASE_PHYS 0x30000000 132 133 /* MC firmware */ 134 /* TODO Actual DPL max length needs to be confirmed with the MC FW team */ 135 #define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000 136 #define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000 137 #define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000 138 #define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000 139 /* For LS2085A */ 140 #define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH 0x200000 141 #define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET 0x07000000 142 143 /* Define phy_reset function to boot the MC based on mcinitcmd. 144 * This happens late enough to properly fixup u-boot env MAC addresses. 145 */ 146 #define CONFIG_RESET_PHY_R 147 148 /* 149 * Carve out a DDR region which will not be used by u-boot/Linux 150 * 151 * It will be used by MC and Debug Server. The MC region must be 152 * 512MB aligned, so the min size to hide is 512MB. 153 */ 154 #ifdef CONFIG_FSL_MC_ENET 155 #define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (128UL * 1024 * 1024) 156 #endif 157 158 /* Command line configuration */ 159 160 /* Miscellaneous configurable options */ 161 #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000) 162 163 /* Physical Memory Map */ 164 /* fixme: these need to be checked against the board */ 165 #define CONFIG_CHIP_SELECTS_PER_CTRL 4 166 167 #define CONFIG_HWCONFIG 168 #define HWCONFIG_BUFFER_SIZE 128 169 170 /* Allow to overwrite serial and ethaddr */ 171 #define CONFIG_ENV_OVERWRITE 172 173 /* Initial environment variables */ 174 #define CONFIG_EXTRA_ENV_SETTINGS \ 175 "hwconfig=fsl_ddr:bank_intlv=auto\0" \ 176 "loadaddr=0x80100000\0" \ 177 "kernel_addr=0x100000\0" \ 178 "ramdisk_addr=0x800000\0" \ 179 "ramdisk_size=0x2000000\0" \ 180 "fdt_high=0xa0000000\0" \ 181 "initrd_high=0xffffffffffffffff\0" \ 182 "kernel_start=0x581000000\0" \ 183 "kernel_load=0xa0000000\0" \ 184 "kernel_size=0x2800000\0" \ 185 "console=ttyAMA0,38400n8\0" \ 186 "mcinitcmd=fsl_mc start mc 0x580a00000" \ 187 " 0x580e00000 \0" 188 189 #ifndef CONFIG_TFABOOT 190 #ifdef CONFIG_SD_BOOT 191 #define CONFIG_BOOTCOMMAND "mmc read 0x80200000 0x6800 0x800;"\ 192 " fsl_mc apply dpl 0x80200000 &&" \ 193 " mmc read $kernel_load $kernel_start" \ 194 " $kernel_size && bootm $kernel_load" 195 #else 196 #define CONFIG_BOOTCOMMAND "fsl_mc apply dpl 0x580d00000 &&" \ 197 " cp.b $kernel_start $kernel_load" \ 198 " $kernel_size && bootm $kernel_load" 199 #endif 200 #endif 201 202 /* Monitor Command Prompt */ 203 #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ 204 #define CONFIG_SYS_MAXARGS 64 /* max command args */ 205 206 #define CONFIG_SPL_BSS_START_ADDR 0x80100000 207 #define CONFIG_SPL_BSS_MAX_SIZE 0x00100000 208 #define CONFIG_SPL_MAX_SIZE 0x16000 209 #define CONFIG_SPL_STACK (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0) 210 #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" 211 #define CONFIG_SPL_TEXT_BASE 0x1800a000 212 213 #ifdef CONFIG_NAND_BOOT 214 #define CONFIG_SYS_NAND_U_BOOT_DST 0x80400000 215 #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST 216 #endif 217 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000 218 #define CONFIG_SYS_SPL_MALLOC_START 0x80200000 219 #define CONFIG_SYS_MONITOR_LEN (1024 * 1024) 220 221 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 222 223 #include <asm/arch/soc.h> 224 225 #endif /* __LS2_COMMON_H */ 226