1 /* SPDX-License-Identifier: GPL-2.0-only */ 2 /* 3 * Extend a 32-bit counter to 63 bits 4 * 5 * Author: Nicolas Pitre 6 * Created: December 3, 2006 7 * Copyright: MontaVista Software, Inc. 8 */ 9 10 #ifndef __LINUX_CNT32_TO_63_H__ 11 #define __LINUX_CNT32_TO_63_H__ 12 13 #include <linux/compiler.h> 14 #include <linux/types.h> 15 #include <asm/byteorder.h> 16 17 /* this is used only to give gcc a clue about good code generation */ 18 union cnt32_to_63 { 19 struct { 20 #if defined(__LITTLE_ENDIAN) 21 u32 lo, hi; 22 #elif defined(__BIG_ENDIAN) 23 u32 hi, lo; 24 #endif 25 }; 26 u64 val; 27 }; 28 29 30 /** 31 * cnt32_to_63 - Expand a 32-bit counter to a 63-bit counter 32 * @cnt_lo: The low part of the counter 33 * 34 * Many hardware clock counters are only 32 bits wide and therefore have 35 * a relatively short period making wrap-arounds rather frequent. This 36 * is a problem when implementing sched_clock() for example, where a 64-bit 37 * non-wrapping monotonic value is expected to be returned. 38 * 39 * To overcome that limitation, let's extend a 32-bit counter to 63 bits 40 * in a completely lock free fashion. Bits 0 to 31 of the clock are provided 41 * by the hardware while bits 32 to 62 are stored in memory. The top bit in 42 * memory is used to synchronize with the hardware clock half-period. When 43 * the top bit of both counters (hardware and in memory) differ then the 44 * memory is updated with a new value, incrementing it when the hardware 45 * counter wraps around. 46 * 47 * Because a word store in memory is atomic then the incremented value will 48 * always be in synch with the top bit indicating to any potential concurrent 49 * reader if the value in memory is up to date or not with regards to the 50 * needed increment. And any race in updating the value in memory is harmless 51 * as the same value would simply be stored more than once. 52 * 53 * The restrictions for the algorithm to work properly are: 54 * 55 * 1) this code must be called at least once per each half period of the 56 * 32-bit counter; 57 * 58 * 2) this code must not be preempted for a duration longer than the 59 * 32-bit counter half period minus the longest period between two 60 * calls to this code; 61 * 62 * Those requirements ensure proper update to the state bit in memory. 63 * This is usually not a problem in practice, but if it is then a kernel 64 * timer should be scheduled to manage for this code to be executed often 65 * enough. 66 * 67 * And finally: 68 * 69 * 3) the cnt_lo argument must be seen as a globally incrementing value, 70 * meaning that it should be a direct reference to the counter data which 71 * can be evaluated according to a specific ordering within the macro, 72 * and not the result of a previous evaluation stored in a variable. 73 * 74 * For example, this is wrong: 75 * 76 * u32 partial = get_hw_count(); 77 * u64 full = cnt32_to_63(partial); 78 * return full; 79 * 80 * This is fine: 81 * 82 * u64 full = cnt32_to_63(get_hw_count()); 83 * return full; 84 * 85 * Note that the top bit (bit 63) in the returned value should be considered 86 * as garbage. It is not cleared here because callers are likely to use a 87 * multiplier on the returned value which can get rid of the top bit 88 * implicitly by making the multiplier even, therefore saving on a runtime 89 * clear-bit instruction. Otherwise caller must remember to clear the top 90 * bit explicitly. 91 */ 92 #define cnt32_to_63(cnt_lo) \ 93 ({ \ 94 static u32 __m_cnt_hi; \ 95 union cnt32_to_63 __x; \ 96 __x.hi = __m_cnt_hi; \ 97 smp_rmb(); \ 98 __x.lo = (cnt_lo); \ 99 if (unlikely((s32)(__x.hi ^ __x.lo) < 0)) \ 100 __m_cnt_hi = __x.hi = (__x.hi ^ 0x80000000) + (__x.hi >> 31); \ 101 __x.val; \ 102 }) 103 104 #endif 105