xref: /openbmc/u-boot/include/configs/wandboard.h (revision b71d9e8b)
1 /* SPDX-License-Identifier: GPL-2.0+ */
2 /*
3  * Copyright (C) 2013 Freescale Semiconductor, Inc.
4  *
5  * Configuration settings for the Wandboard.
6  */
7 
8 #ifndef __CONFIG_H
9 #define __CONFIG_H
10 
11 #include "mx6_common.h"
12 
13 #include "imx6_spl.h"
14 
15 #define CONFIG_MACH_TYPE		MACH_TYPE_WANDBOARD_IMX6
16 
17 /* Size of malloc() pool */
18 #define CONFIG_SYS_MALLOC_LEN		(10 * SZ_1M)
19 
20 #define CONFIG_MXC_UART
21 #define CONFIG_MXC_UART_BASE		UART1_BASE
22 
23 /* SATA Configs */
24 
25 #ifdef CONFIG_CMD_SATA
26 #define CONFIG_SYS_SATA_MAX_DEVICE	1
27 #define CONFIG_DWC_AHSATA_PORT_ID	0
28 #define CONFIG_DWC_AHSATA_BASE_ADDR	SATA_ARB_BASE_ADDR
29 #define CONFIG_LBA48
30 #endif
31 
32 #define CONFIG_SYS_MEMTEST_START	0x10000000
33 #define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 500 * SZ_1M)
34 
35 /* I2C Configs */
36 #define CONFIG_SYS_I2C
37 #define CONFIG_SYS_I2C_MXC
38 #define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
39 #define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
40 #define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
41 #define CONFIG_SYS_I2C_SPEED		100000
42 
43 /* PMIC */
44 #define CONFIG_POWER
45 #define CONFIG_POWER_I2C
46 #define CONFIG_POWER_PFUZE100
47 #define CONFIG_POWER_PFUZE100_I2C_ADDR	0x08
48 
49 /* MMC Configuration */
50 #define CONFIG_SYS_FSL_USDHC_NUM	2
51 #define CONFIG_SYS_FSL_ESDHC_ADDR	0
52 
53 /* USB Configs */
54 #define CONFIG_USB_MAX_CONTROLLER_COUNT	2
55 #define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
56 #define CONFIG_MXC_USB_FLAGS		0
57 
58 /* Ethernet Configuration */
59 #define CONFIG_FEC_MXC
60 #define IMX_FEC_BASE			ENET_BASE_ADDR
61 #define CONFIG_FEC_XCV_TYPE		RGMII
62 #define CONFIG_ETHPRIME			"FEC"
63 #define CONFIG_FEC_MXC_PHYADDR		1
64 #define CONFIG_PHY_ATHEROS
65 
66 /* Framebuffer */
67 #ifdef CONFIG_VIDEO
68 #define CONFIG_VIDEO_IPUV3
69 #define CONFIG_VIDEO_BMP_RLE8
70 #define CONFIG_SPLASH_SCREEN
71 #define CONFIG_SPLASH_SCREEN_ALIGN
72 #define CONFIG_BMP_16BPP
73 #define CONFIG_VIDEO_LOGO
74 #define CONFIG_VIDEO_BMP_LOGO
75 #define CONFIG_IMX_HDMI
76 #define CONFIG_IMX_VIDEO_SKIP
77 #endif
78 
79 #define CONFIG_EXTRA_ENV_SETTINGS \
80 	"console=ttymxc0\0" \
81 	"splashpos=m,m\0" \
82 	"fdtfile=undefined\0" \
83 	"fdt_high=0xffffffff\0" \
84 	"initrd_high=0xffffffff\0" \
85 	"fdt_addr_r=0x18000000\0" \
86 	"fdt_addr=0x18000000\0" \
87 	"ip_dyn=yes\0" \
88 	"mmcdev=" __stringify(CONFIG_SYS_MMC_ENV_DEV) "\0" \
89 	"finduuid=part uuid mmc 0:1 uuid\0" \
90 	"update_sd_firmware_filename=u-boot.imx\0" \
91 	"update_sd_firmware=" \
92 		"if test ${ip_dyn} = yes; then " \
93 			"setenv get_cmd dhcp; " \
94 		"else " \
95 			"setenv get_cmd tftp; " \
96 		"fi; " \
97 		"if mmc dev ${mmcdev}; then "	\
98 			"if ${get_cmd} ${update_sd_firmware_filename}; then " \
99 				"setexpr fw_sz ${filesize} / 0x200; " \
100 				"setexpr fw_sz ${fw_sz} + 1; "	\
101 				"mmc write ${loadaddr} 0x2 ${fw_sz}; " \
102 			"fi; "	\
103 		"fi\0" \
104 	"findfdt="\
105 		"if test $board_name = D1 && test $board_rev = MX6QP ; then " \
106 			"setenv fdtfile imx6qp-wandboard-revd1.dtb; fi; " \
107 		"if test $board_name = D1 && test $board_rev = MX6Q ; then " \
108 			"setenv fdtfile imx6q-wandboard-revd1.dtb; fi; " \
109 		"if test $board_name = D1 && test $board_rev = MX6DL ; then " \
110 			"setenv fdtfile imx6dl-wandboard-revd1.dtb; fi; " \
111 		"if test $board_name = C1 && test $board_rev = MX6Q ; then " \
112 			"setenv fdtfile imx6q-wandboard.dtb; fi; " \
113 		"if test $board_name = C1 && test $board_rev = MX6DL ; then " \
114 			"setenv fdtfile imx6dl-wandboard.dtb; fi; " \
115 		"if test $board_name = B1 && test $board_rev = MX6Q ; then " \
116 			"setenv fdtfile imx6q-wandboard-revb1.dtb; fi; " \
117 		"if test $board_name = B1 && test $board_rev = MX6DL ; then " \
118 			"setenv fdtfile imx6dl-wandboard-revb1.dtb; fi; " \
119 		"if test $fdtfile = undefined; then " \
120 			"echo WARNING: Could not determine dtb to use; fi; \0" \
121 	"kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
122 	"pxefile_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
123 	"ramdisk_addr_r=0x13000000\0" \
124 	"ramdiskaddr=0x13000000\0" \
125 	"scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \
126 	BOOTENV
127 
128 #define BOOT_TARGET_DEVICES(func) \
129 	func(MMC, mmc, 0) \
130 	func(MMC, mmc, 1) \
131 	func(SATA, sata, 0) \
132 	func(USB, usb, 0) \
133 	func(PXE, pxe, na) \
134 	func(DHCP, dhcp, na)
135 
136 #include <config_distro_bootcmd.h>
137 
138 /* Physical Memory Map */
139 #define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
140 
141 #define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
142 #define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
143 #define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
144 
145 #define CONFIG_SYS_INIT_SP_OFFSET \
146 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
147 #define CONFIG_SYS_INIT_SP_ADDR \
148 	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
149 
150 /* Environment organization */
151 #define CONFIG_ENV_SIZE			(8 * 1024)
152 
153 #define CONFIG_ENV_OFFSET		(768 * 1024)
154 #define CONFIG_SYS_MMC_ENV_DEV		0
155 
156 #endif			       /* __CONFIG_H * */
157