1=========================================== 2QEMU Firmware Configuration (fw_cfg) Device 3=========================================== 4 5Guest-side Hardware Interface 6============================= 7 8This hardware interface allows the guest to retrieve various data items 9(blobs) that can influence how the firmware configures itself, or may 10contain tables to be installed for the guest OS. Examples include device 11boot order, ACPI and SMBIOS tables, virtual machine UUID, SMP and NUMA 12information, kernel/initrd images for direct (Linux) kernel booting, etc. 13 14Selector (Control) Register 15--------------------------- 16 17* Write only 18* Location: platform dependent (IOport or MMIO) 19* Width: 16-bit 20* Endianness: little-endian (if IOport), or big-endian (if MMIO) 21 22A write to this register sets the index of a firmware configuration 23item which can subsequently be accessed via the data register. 24 25Setting the selector register will cause the data offset to be set 26to zero. The data offset impacts which data is accessed via the data 27register, and is explained below. 28 29Bit14 of the selector register indicates whether the configuration 30setting is being written. A value of 0 means the item is only being 31read, and all write access to the data port will be ignored. A value 32of 1 means the item's data can be overwritten by writes to the data 33register. In other words, configuration write mode is enabled when 34the selector value is between 0x4000-0x7fff or 0xc000-0xffff. 35 36.. NOTE:: 37 As of QEMU v2.4, writes to the fw_cfg data register are no 38 longer supported, and will be ignored (treated as no-ops)! 39 40.. NOTE:: 41 As of QEMU v2.9, writes are reinstated, but only through the DMA 42 interface (see below). Furthermore, writeability of any specific item is 43 governed independently of Bit14 in the selector key value. 44 45Bit15 of the selector register indicates whether the configuration 46setting is architecture specific. A value of 0 means the item is a 47generic configuration item. A value of 1 means the item is specific 48to a particular architecture. In other words, generic configuration 49items are accessed with a selector value between 0x0000-0x7fff, and 50architecture specific configuration items are accessed with a selector 51value between 0x8000-0xffff. 52 53Data Register 54------------- 55 56* Read/Write (writes ignored as of QEMU v2.4, but see the DMA interface) 57* Location: platform dependent (IOport [#]_ or MMIO) 58* Width: 8-bit (if IOport), 8/16/32/64-bit (if MMIO) 59* Endianness: string-preserving 60 61.. [#] 62 On platforms where the data register is exposed as an IOport, its 63 port number will always be one greater than the port number of the 64 selector register. In other words, the two ports overlap, and can not 65 be mapped separately. 66 67The data register allows access to an array of bytes for each firmware 68configuration data item. The specific item is selected by writing to 69the selector register, as described above. 70 71Initially following a write to the selector register, the data offset 72will be set to zero. Each successful access to the data register will 73increment the data offset by the appropriate access width. 74 75Each firmware configuration item has a maximum length of data 76associated with the item. After the data offset has passed the 77end of this maximum data length, then any reads will return a data 78value of 0x00, and all writes will be ignored. 79 80An N-byte wide read of the data register will return the next available 81N bytes of the selected firmware configuration item, as a substring, in 82increasing address order, similar to memcpy(). 83 84Register Locations 85------------------ 86 87x86, x86_64 88 * Selector Register IOport: 0x510 89 * Data Register IOport: 0x511 90 * DMA Address IOport: 0x514 91 92Arm 93 * Selector Register address: Base + 8 (2 bytes) 94 * Data Register address: Base + 0 (8 bytes) 95 * DMA Address address: Base + 16 (8 bytes) 96 97ACPI Interface 98-------------- 99 100The fw_cfg device is defined with ACPI ID ``QEMU0002``. Since we expect 101ACPI tables to be passed into the guest through the fw_cfg device itself, 102the guest-side firmware can not use ACPI to find fw_cfg. However, once the 103firmware is finished setting up ACPI tables and hands control over to the 104guest kernel, the latter can use the fw_cfg ACPI node for a more accurate 105inventory of in-use IOport or MMIO regions. 106 107Firmware Configuration Items 108---------------------------- 109 110Signature (Key 0x0000, ``FW_CFG_SIGNATURE``) 111~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 112 113The presence of the fw_cfg selector and data registers can be verified 114by selecting the "signature" item using key 0x0000 (``FW_CFG_SIGNATURE``), 115and reading four bytes from the data register. If the fw_cfg device is 116present, the four bytes read will contain the characters ``QEMU``. 117 118If the DMA interface is available, then reading the DMA Address 119Register returns 0x51454d5520434647 (``QEMU CFG`` in big-endian format). 120 121Revision / feature bitmap (Key 0x0001, ``FW_CFG_ID``) 122~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 123 124A 32-bit little-endian unsigned int, this item is used to check for enabled 125features. 126 127- Bit 0: traditional interface. Always set. 128- Bit 1: DMA interface. 129 130File Directory (Key 0x0019, ``FW_CFG_FILE_DIR``) 131~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 132 133.. highlight:: c 134 135Firmware configuration items stored at selector keys 0x0020 or higher 136(``FW_CFG_FILE_FIRST`` or higher) have an associated entry in a directory 137structure, which makes it easier for guest-side firmware to identify 138and retrieve them. The format of this file directory (from ``fw_cfg.h`` in 139the QEMU source tree) is shown here, slightly annotated for clarity:: 140 141 struct FWCfgFiles { /* the entire file directory fw_cfg item */ 142 uint32_t count; /* number of entries, in big-endian format */ 143 struct FWCfgFile f[]; /* array of file entries, see below */ 144 }; 145 146 struct FWCfgFile { /* an individual file entry, 64 bytes total */ 147 uint32_t size; /* size of referenced fw_cfg item, big-endian */ 148 uint16_t select; /* selector key of fw_cfg item, big-endian */ 149 uint16_t reserved; 150 char name[56]; /* fw_cfg item name, NUL-terminated ascii */ 151 }; 152 153All Other Data Items 154~~~~~~~~~~~~~~~~~~~~ 155 156Please consult the QEMU source for the most up-to-date and authoritative list 157of selector keys and their respective items' purpose, format and writeability. 158 159Ranges 160~~~~~~ 161 162Theoretically, there may be up to 0x4000 generic firmware configuration 163items, and up to 0x4000 architecturally specific ones. 164 165=============== =========== 166Selector Reg. Range Usage 167=============== =========== 1680x0000 - 0x3fff Generic (0x0000 - 0x3fff, generally RO, possibly RW through 169 the DMA interface in QEMU v2.9+) 1700x4000 - 0x7fff Generic (0x0000 - 0x3fff, RW, ignored in QEMU v2.4+) 1710x8000 - 0xbfff Arch. Specific (0x0000 - 0x3fff, generally RO, possibly RW 172 through the DMA interface in QEMU v2.9+) 1730xc000 - 0xffff Arch. Specific (0x0000 - 0x3fff, RW, ignored in v2.4+) 174=============== =========== 175 176In practice, the number of allowed firmware configuration items depends on the 177machine type/version. 178 179Guest-side DMA Interface 180======================== 181 182If bit 1 of the feature bitmap is set, the DMA interface is present. This does 183not replace the existing fw_cfg interface, it is an add-on. This interface 184can be used through the 64-bit wide address register. 185 186The address register is in big-endian format. The value for the register is 0 187at startup and after an operation. A write to the least significant half (at 188offset 4) triggers an operation. This means that operations with 32-bit 189addresses can be triggered with just one write, whereas operations with 19064-bit addresses can be triggered with one 64-bit write or two 32-bit writes, 191starting with the most significant half (at offset 0). 192 193In this register, the physical address of a ``FWCfgDmaAccess`` structure in RAM 194should be written. This is the format of the ``FWCfgDmaAccess`` structure:: 195 196 typedef struct FWCfgDmaAccess { 197 uint32_t control; 198 uint32_t length; 199 uint64_t address; 200 } FWCfgDmaAccess; 201 202The fields of the structure are in big endian mode, and the field at the lowest 203address is the ``control`` field. 204 205The ``control`` field has the following bits: 206 207- Bit 0: Error 208- Bit 1: Read 209- Bit 2: Skip 210- Bit 3: Select. The upper 16 bits are the selected index. 211- Bit 4: Write 212 213When an operation is triggered, if the ``control`` field has bit 3 set, the 214upper 16 bits are interpreted as an index of a firmware configuration item. 215This has the same effect as writing the selector register. 216 217If the ``control`` field has bit 1 set, a read operation will be performed. 218``length`` bytes for the current selector and offset will be copied into the 219physical RAM address specified by the ``address`` field. 220 221If the ``control`` field has bit 4 set (and not bit 1), a write operation will be 222performed. ``length`` bytes will be copied from the physical RAM address 223specified by the ``address`` field to the current selector and offset. QEMU 224prevents starting or finishing the write beyond the end of the item associated 225with the current selector (i.e., the item cannot be resized). Truncated writes 226are dropped entirely. Writes to read-only items are also rejected. All of these 227write errors set bit 0 (the error bit) in the ``control`` field. 228 229If the ``control`` field has bit 2 set (and neither bit 1 nor bit 4), a skip 230operation will be performed. The offset for the current selector will be 231advanced ``length`` bytes. 232 233To check the result, read the ``control`` field: 234 235Error bit set 236 Something went wrong. 237All bits cleared 238 Transfer finished successfully. 239Otherwise 240 Transfer still in progress 241 (doesn't happen today due to implementation not being async, 242 but may in the future). 243 244Externally Provided Items 245========================= 246 247Since v2.4, "file" fw_cfg items (i.e., items with selector keys above 248``FW_CFG_FILE_FIRST``, and with a corresponding entry in the fw_cfg file 249directory structure) may be inserted via the QEMU command line, using 250the following syntax:: 251 252 -fw_cfg [name=]<item_name>,file=<path> 253 254Or:: 255 256 -fw_cfg [name=]<item_name>,string=<string> 257 258Since v5.1, QEMU allows some objects to generate fw_cfg-specific content, 259the content is then associated with a "file" item using the 'gen_id' option 260in the command line, using the following syntax:: 261 262 -object <generator-type>,id=<generated_id>,[generator-specific-options] \ 263 -fw_cfg [name=]<item_name>,gen_id=<generated_id> 264 265See QEMU man page for more documentation. 266 267Using item_name with plain ASCII characters only is recommended. 268 269Item names beginning with ``opt/`` are reserved for users. QEMU will 270never create entries with such names unless explicitly ordered by the 271user. 272 273To avoid clashes among different users, it is strongly recommended 274that you use names beginning with ``opt/RFQDN/``, where RFQDN is a reverse 275fully qualified domain name you control. For instance, if SeaBIOS 276wanted to define additional names, the prefix ``opt/org.seabios/`` would 277be appropriate. 278 279For historical reasons, ``opt/ovmf/`` is reserved for OVMF firmware. 280 281Prefix ``opt/org.qemu/`` is reserved for QEMU itself. 282 283Use of names not beginning with ``opt/`` is potentially dangerous and 284entirely unsupported. QEMU will warn if you try. 285 286Use of names not beginning with ``opt/`` is tolerated with 'gen_id' (that 287is, the warning is suppressed), but you must know exactly what you're 288doing. 289 290All externally provided fw_cfg items are read-only to the guest. 291