1Device tree bindings for Texas instruments Davinci/Keystone NAND controller
2
3This file provides information, what the device node for the davinci/keystone
4NAND interface contains.
5
6Documentation:
7Davinci DM646x - https://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf
8Kestone - https://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
9
10Required properties:
11
12- compatible:			"ti,davinci-nand"
13				"ti,keystone-nand"
14
15- reg:				Contains 2 offset/length values:
16				- offset and length for the access window.
17				- offset and length for accessing the AEMIF
18				control registers.
19
20- ti,davinci-chipselect:	number of chipselect. Indicates on the
21				davinci_nand driver which chipselect is used
22				for accessing the nand.
23				Can be in the range [0-3].
24
25Recommended properties :
26
27- ti,davinci-mask-ale:		mask for ALE. Needed for executing address
28				phase. These offset will be added to the base
29				address for the chip select space the NAND Flash
30				device is connected to.
31				If not set equal to 0x08.
32
33- ti,davinci-mask-cle:		mask for CLE. Needed for executing command
34				phase. These offset will be added to the base
35				address for the chip select space the NAND Flash
36				device is connected to.
37				If not set equal to 0x10.
38
39- ti,davinci-mask-chipsel:	mask for chipselect address. Needed to mask
40				addresses for given chipselect.
41
42- nand-ecc-mode:		operation mode of the NAND ecc mode. ECC mode
43				valid values for davinci driver:
44				- "none"
45				- "soft"
46				- "hw"
47
48- ti,davinci-ecc-bits:		used ECC bits, currently supported 1 or 4.
49
50- nand-bus-width:		buswidth 8 or 16. If not present 8.
51
52- nand-on-flash-bbt:		use flash based bad block table support. OOB
53				identifier is saved in OOB area. If not present
54				false.
55
56Deprecated properties:
57
58- ti,davinci-ecc-mode:		operation mode of the NAND ecc mode. ECC mode
59				valid values for davinci driver:
60				- "none"
61				- "soft"
62				- "hw"
63
64- ti,davinci-nand-buswidth:	buswidth 8 or 16. If not present 8.
65
66- ti,davinci-nand-use-bbt:	use flash based bad block table support. OOB
67				identifier is saved in OOB area. If not present
68				false.
69
70Nand device bindings may contain additional sub-nodes describing partitions of
71the address space. See partition.txt for more detail. The NAND Flash timing
72values must be programmed in the chip select’s node of AEMIF
73memory-controller (see Documentation/devicetree/bindings/memory-controllers/
74davinci-aemif.txt).
75
76Example(da850 EVM ):
77
78nand_cs3@62000000 {
79	compatible = "ti,davinci-nand";
80	reg = <0x62000000 0x807ff
81	       0x68000000 0x8000>;
82	ti,davinci-chipselect = <1>;
83	ti,davinci-mask-ale = <0>;
84	ti,davinci-mask-cle = <0>;
85	ti,davinci-mask-chipsel = <0>;
86	nand-ecc-mode = "hw";
87	ti,davinci-ecc-bits = <4>;
88	nand-on-flash-bbt;
89
90	partition@180000 {
91		label = "ubifs";
92		reg = <0x180000 0x7e80000>;
93	};
94};
95