/openbmc/linux/security/apparmor/ |
H A D | Kconfig | 115 KUnit tests run during boot and output the results to the debug log
|
/openbmc/linux/arch/mips/include/asm/ |
H A D | sgiarcs.h | 77 bogus, ronly, removable, consin, consout, input, output enumerator
|
/openbmc/linux/arch/arm64/boot/dts/allwinner/ |
H A D | sun50i-h6-beelink-gs1.dts | 41 clock-output-names = "ext_osc32k";
|
/openbmc/linux/net/ipv6/ |
H A D | rpl_iptunnel.c | 348 .output = rpl_output,
|
/openbmc/linux/include/net/ |
H A D | ip6_route.h | 267 int (*output)(struct net *, struct sock *, struct sk_buff *));
|
/openbmc/linux/drivers/iio/dac/ |
H A D | ad5791.c | 294 .output = 1, \
|
/openbmc/qemu/tests/qemu-iotests/ |
H A D | 034.out | 1 QA output created by 034
|
/openbmc/linux/arch/arm/boot/dts/qcom/ |
H A D | qcom-msm8960-cdp.dts | 79 output-low;
|
H A D | qcom-ipq8064-rb3011.dts | 459 output-high;
|
/openbmc/linux/drivers/media/i2c/ |
H A D | vpx3220.c | 370 u32 input, u32 output, u32 config) in vpx3220_s_routing() argument
|
/openbmc/linux/arch/arm/boot/dts/nxp/imx/ |
H A D | imx6dl-eckelmann-ci4x10.dts | 31 clock-output-names = "enet_ref_pad";
|
H A D | imx6dl-plybas.dts | 78 clock-output-names = "enet_ref_pad";
|
/openbmc/u-boot/board/LaCie/net2big_v2/ |
H A D | kwbimage.cfg | 101 # bit12: 0, DDR output buffer enabled
|
/openbmc/phosphor-mboxd/ |
H A D | README.md | 100 We have two scenarios where we care about output, with the important
|
/openbmc/linux/Documentation/driver-api/rapidio/ |
H A D | mport_cdev.rst | 92 Use CONFIG_RAPIDIO_DEBUG=y to enable debug output at the top level.
|
/openbmc/linux/Documentation/firmware-guide/acpi/ |
H A D | video_extension.rst | 11 setup a video output, etc. Note that this is an ref. implementation
|
/openbmc/u-boot/board/keymile/km_arm/ |
H A D | kwbimage.cfg | 113 # bit12: 0, DDR output buffer enabled
|
/openbmc/u-boot/doc/ |
H A D | README.nokia_rx51 | 22 output with ANSI espace codes and the N900 HW keyboard input. USB tty works
|
/openbmc/linux/tools/testing/selftests/mm/ |
H A D | run_vmtests.sh | 21 -n: disable TAP output
|
/openbmc/u-boot/board/LaCie/netspace_v2/ |
H A D | kwbimage-ns2l.cfg | 101 # bit12: 0, DDR output buffer enabled
|
/openbmc/linux/arch/arm/mach-omap1/ |
H A D | Kconfig | 50 bool "Multiplexing debug output"
|
/openbmc/linux/arch/arm/boot/dts/aspeed/ |
H A D | aspeed-bmc-vegman-rx20.dts | 78 /* SGPIO lines. even: input, odd: output */
|
/openbmc/linux/Documentation/driver-api/ |
H A D | switchtec.rst | 48 the 4-byte Command Return Value plus up to 1024 bytes of output
|
/openbmc/u-boot/doc/device-tree-bindings/pinctrl/ |
H A D | rockchip,pinctrl.txt | 5 multiplexing the PAD input/output signals. For each PAD there are several
|
/openbmc/linux/drivers/gpu/drm/msm/ |
H A D | NOTES | 12 Plus a handful of blocks around them for HDMI/DSI/etc output.
|