| /openbmc/linux/arch/arm/boot/dts/nxp/ls/ |
| H A D | ls1021a-tqmls1021a.dtsi | 25 /* e-MMC over 8 data lines */
|
| /openbmc/linux/Documentation/tools/rtla/ |
| H A D | rtla-timerlat-hist.rst | 37 in the cpus *0-4*, *skipping zero* only lines. Moreover, **rtla timerlat
|
| /openbmc/linux/Documentation/devicetree/bindings/reset/ |
| H A D | xlnx,zynqmp-reset.yaml | 21 lines should specify them as a reset phandle in their corresponding
|
| /openbmc/linux/drivers/leds/blink/ |
| H A D | Kconfig | 20 This option enables support for LEDs connected to GPIO lines on
|
| /openbmc/linux/Documentation/devicetree/bindings/iio/adc/ |
| H A D | adi,axi-adc.yaml | 18 to the data-lines of the ADC and handle the streaming of data into
|
| /openbmc/phosphor-power/phosphor-regulators/docs/config_file/ |
| H A D | chassis.md | 18 | comments | no | array of strings | One or more comment lines describing …
|
| H A D | sensor_monitoring.md | 26 | comments | no | array of strings | One or more comment lines descri…
|
| /openbmc/linux/Documentation/driver-api/usb/ |
| H A D | writing_musb_glue_layer.rst | 124 :emphasize-lines: 8,12,18
169 The first few lines of the probe function allocate and assign the glue,
185 :emphasize-lines: 3,5,7,9,16
245 :emphasize-lines: 12,14
320 :emphasize-lines: 5,6
345 :emphasize-lines: 7,9-11,14,24
438 :emphasize-lines: 2,7,14-17,21,22,25,26,28,29
522 :emphasize-lines: 3,5,7-9,11
587 :emphasize-lines: 12
641 :emphasize-lines: 18-19
|
| /openbmc/openbmc/poky/meta/lib/oe/ |
| H A D | package.py | 297 lines = fd.readlines()
299 for l in lines:
1573 lines = fd.readlines()
1576 for l in lines:
1581 for l in lines:
1836 lines = f.readlines()
1837 for l in lines:
1867 lines = fd.readlines()
1869 for l in lines:
1898 lines = fd.readlines()
[all …]
|
| /openbmc/linux/Documentation/devicetree/bindings/bus/ |
| H A D | ts-nbus.txt | 11 - ts,data-gpios : The 8 GPIO pins connected to the data lines on the FPGA
|
| /openbmc/linux/Documentation/devicetree/bindings/net/ |
| H A D | nokia-bluetooth.txt | 8 UART status lines for wakeup of UART transceivers to improve power management
|
| /openbmc/openbmc/meta-openembedded/meta-oe/recipes-support/minini/ |
| H A D | minini_1.2.b.bb | 6 all in 830 lines of (commented) source code (version 1.2) in C (the code also \
|
| /openbmc/u-boot/doc/device-tree-bindings/leds/ |
| H A D | leds-gpio.txt | 1 LEDs connected to GPIO lines
|
| /openbmc/openbmc/meta-openembedded/meta-oe/recipes-support/gd/ |
| H A D | gd_2.3.3.bb | 3 complete with lines, arcs, text, multiple colors, cut and paste from other \
|
| /openbmc/openbmc/meta-openembedded/meta-oe/recipes-support/daemontools/ |
| H A D | daemontools_0.76.bb | 8 each line and, for each log, includes or excludes lines matching specified \
|
| /openbmc/openbmc/meta-openembedded/meta-oe/recipes-extended/liblockfile/liblockfile/ |
| H A D | 0001-Makefile.in-redefine-LOCKPROG.patch | 15 Update patch for 1.17, also redefine LOCKPROG in other lines
|
| /openbmc/openbmc/poky/scripts/contrib/bb-perf/ |
| H A D | bb-matrix-plot.sh | 110 splot "$DATFILE" every ::1 using 1:2:$FIELD with lines ls 100
|
| /openbmc/linux/Documentation/devicetree/bindings/leds/ |
| H A D | ti,tca6507.yaml | 14 7 separate lines either by holding them low, or by pulsing them with modulated
|
| /openbmc/linux/Documentation/hwmon/ |
| H A D | vexpress.rst | 32 providing information about power lines voltages and currents, board
|
| /openbmc/linux/Documentation/fb/ |
| H A D | matroxfb.rst | 13 * It provides a nice large console (128 cols + 48 lines with 1024x768)
263 yres:X vertical resolution, in pixel lines. Default is derived from `vesa`
265 upper:X top boundary: lines between end of VSYNC pulse and start of first
267 lower:X bottom boundary: lines between end of picture and start of VSYNC
269 vslen:X length of VSYNC pulse, in lines. Default is derived from `vesa`
418 to change it to TV mode. Also, you must select at least 525 lines for
419 NTSC output and 625 lines for PAL output.
|
| /openbmc/linux/Documentation/firmware-guide/acpi/ |
| H A D | intel-pmc-mux.rst | 93 Depending on the platform, the data and SBU lines coming from the connector may
98 (SBU) and "hsl-orientation" (data) to know if those lines are "fixed", and to
|
| /openbmc/qemu/docs/devel/ |
| H A D | submitting-a-pull-request.rst | 34 **Don't forget to add Reviewed-by: and Acked-by: lines**. When other
53 request. As a submaintainer you're one of QEMU's lines of defense
|
| /openbmc/linux/Documentation/driver-api/media/drivers/ccs/ |
| H A D | ccs.rst | 34 crop at the end of the lines and frames.
47 lines and frames.
|
| /openbmc/linux/arch/arm/boot/dts/gemini/ |
| H A D | gemini-sl93512r.dts | 173 * gpio1dgrp cover lines used by SPI for
221 /* The data lines all have default skew */
|
| /openbmc/linux/arch/arm/boot/dts/st/ |
| H A D | ste-ux500-samsung-codina-tmo.dts | 769 /* Mux in all the data lines */
772 /* Data lines D0-D7 GPIO70..GPIO77 */
774 /* Data lines D8-D11 GPIO78..GPIO81 */
776 /* Data lines D12-D15 GPIO82..GPIO85 */
778 /* Data lines D16-D23 GPIO161..GPIO168 */
|