Home
last modified time | relevance | path

Searched refs:using (Results 376 – 400 of 4874) sorted by relevance

1...<<11121314151617181920>>...195

/openbmc/linux/Documentation/devicetree/bindings/leds/
H A Drichtek,rt8515.yaml15 current for each mode is defined in hardware using two resistors
59 is hardwired to the component using the RFS resistor to
71 is hardwired to the component using the RTS resistor to
/openbmc/openbmc/meta-openembedded/meta-oe/recipes-dbs/psqlodbc/files/
H A Dpsqlodbc-remove-some-checks-for-cross-compiling.patch88 - AC_MSG_NOTICE([using $ODBC_INCLUDE $ODBC_LIBDIR])
89 - AC_MSG_NOTICE([using $LIBODBC for regression test])
94 +AC_MSG_NOTICE([using $ODBC_INCLUDE $ODBC_LIBS])
/openbmc/linux/Documentation/driver-api/pldmfw/
H A Dindex.rst7 ``pldmfw`` implements functionality for updating the flash on a device using
25 It is implemented using an ops table that allows device drivers to provide
31 so, it sends the record and component data to the firmware using the device
/openbmc/linux/Documentation/leds/
H A Dleds-qcom-lpg.rst27 The pattern for a channel can be programmed using the "pattern" trigger, using
69 Similarly, the last entry can be stretched by using a higher hold-time on the
/openbmc/linux/Documentation/devicetree/bindings/mfd/
H A Dda9062.txt55 The DA9062 regulators are bound using their names listed below:
66 The DA9061 regulators are bound using their names listed below:
80 regulator-initial-mode may be specified for buck regulators using mode values
H A Dtwl4030-power.txt17 When using ti,twl4030-power-idle, the TI recommended configuration
20 When using ti,twl4030-power-idle-osc-off, the TI recommended
/openbmc/linux/drivers/of/unittest-data/
H A Doverlay_3.dtso5 /* overlay_3 - disable using label */
H A Doverlay_2.dtso5 /* overlay_2 - enable using label */
/openbmc/linux/drivers/platform/chrome/wilco_ec/
H A DKconfig31 userspace daemon from /dev/wilco_event using read() and poll().
38 /dev/wilco_telem0 using write() and then read().
/openbmc/linux/Documentation/filesystems/
H A Defivarfs.rst8 using entries in sysfs to maintain EFI variables. The old sysfs EFI
30 displayed, for example using "hexdump", pay attention that the first
/openbmc/linux/drivers/pnp/
H A DKconfig15 or using a user-space utility.
20 using user space utilities such as the isapnptools package.
/openbmc/linux/Documentation/usb/
H A Dohci.rst23 - less code, by using the upper level "hcd" framework
29 transfers. Previously, using periods of one frame would risk data loss due
/openbmc/linux/Documentation/devicetree/bindings/regulator/
H A Dtps65217.txt11 using the standard binding for regulators found at
20 Each regulator is defined using the standard binding for regulators.
/openbmc/openbmc/poky/meta/recipes-devtools/intltool/intltool/
H A Dremove-perl-check.patch2 the one that the intltool scripts will actually be using (as they hard-code a
3 specific binary), for example in the intltool-native case they'll be using
/openbmc/openbmc/poky/meta/recipes-support/apr/apr-util/
H A Dconfigfix.patch27 - ### avoid using -L if libdir is a "standard" location like /usr/lib
41 - ### avoid using -L if libdir is a "standard" location like /usr/lib
/openbmc/u-boot/doc/imx/common/
H A Dimx5.txt10 This option should be enabled by all boards using the i.MX51 silicon
27 2.1 MAC Address: It is stored in the words 9 to 14 of fuse bank 1, using the
/openbmc/u-boot/doc/
H A DREADME.fsl_iim21 See the README files of the SoCs using this driver in order to know the
29 using "Word y of Bank x" from the register summary in 30.3.2. This is
/openbmc/linux/Documentation/driver-api/firmware/
H A Ddirect-fs-lookup.rst24 however note that using initrd does not suffice to address the same race.
28 remote-proc subsystem. For such cases using a userspace fallback mechanism
/openbmc/openbmc/meta-openpower/
H A DREADME.md31 meta-openpower patches are reviewed using the Gerrit instance at
34 Please submit patches to Gerrit. More information on using Gerrit can be found
/openbmc/phosphor-power/phosphor-regulators/docs/config_file/
H A Dconfiguration.md27 … | Output voltage expressed as a decimal number. Applied using the [pmbus_write_v…
39 "comments": [ "Set rail to 1.25V using standard rule" ],
/openbmc/qemu/docs/system/openrisc/
H A Dvirt.rst19 * SMP (OpenRISC multicore using ompic)
24 The virt machine can be started using the ``-kernel`` and ``-initrd`` options
/openbmc/openbmc/meta-phosphor/recipes-support/nss-pam-ldapd/
H A Dnss-pam-ldapd_0.9.8.bb1 SUMMARY = "NSS and PAM module for using LDAP as a naming service"
3 daemon for NSS and PAM lookups using LDAP \
/openbmc/linux/arch/arm64/boot/dts/qcom/
H A Dsc7180-trogdor-coachz-r1.dts20 * to avoid using bogus temperature values.
41 * skin temperature thermal zone to avoid using bogus temperature values.
/openbmc/linux/arch/arm/mach-mmp/
H A DKconfig24 Include support for Marvell MMP2 based platforms using
38 Include support for Marvell MMP2 based platforms using
/openbmc/linux/Documentation/ABI/stable/
H A Dsysfs-bus-mhi6 using a BHI (Boot Host Interface) register read after at least
17 obtained using a BHI (Boot Host Interface) register read after

1...<<11121314151617181920>>...195