| /openbmc/linux/arch/arm/boot/dts/samsung/ |
| H A D | exynos3250-rinato.dts | 149 pullup-uv = <1800000>;
150 pullup-ohm = <100000>;
157 pullup-uv = <1800000>;
158 pullup-ohm = <100000>;
|
| /openbmc/linux/arch/arm/boot/dts/ti/omap/ |
| H A D | am335x-bonegreen-wireless.dts | 116 /* introduces a pullup on the line and wilink8 ends up in a bad state. */
|
| /openbmc/linux/Documentation/devicetree/bindings/pinctrl/ |
| H A D | lantiq,pinctrl-falcon.txt | 24 Similarly, a pin subnode that describes a pullup parameter implies no
|
| H A D | qcom,apq8064-pinctrl.txt | 38 Similarly, a pin subnode that describes a pullup parameter implies no
|
| H A D | qcom,ipq8064-pinctrl.txt | 38 Similarly, a pin subnode that describes a pullup parameter implies no
|
| H A D | qcom,ipq4019-pinctrl.txt | 41 Similarly, a pin subnode that describes a pullup parameter implies no
|
| H A D | pinctrl-palmas.txt | 28 Similarly, a pin subnode that describes a pullup parameter implies no
|
| /openbmc/linux/arch/arm/boot/dts/microchip/ |
| H A D | at91-wb50n.dtsi | 28 …<AT91_PIOC 26 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PC26 GPIO with pullup deglitch */
|
| /openbmc/linux/drivers/usb/gadget/udc/ |
| H A D | dummy_hcd.c | 276 unsigned pullup:1; member
376 } else if (!dum->pullup || dum->udc_suspended) { in set_link_state_by_speed()
401 } else if (!dum->pullup || dum->udc_suspended) { in set_link_state_by_speed()
436 if (dum->pullup) in set_link_state()
905 dum->pullup = (value != 0); in dummy_pullup()
955 .pullup = dummy_pullup,
2199 if (dum_hcd->dum->pullup) { in dummy_hub_control()
|
| /openbmc/linux/arch/arm64/boot/dts/rockchip/ |
| H A D | rk3399-gru-chromebook.dtsi | 470 * Note strange pullup enable. Apparently this avoids leakage but
472 * transfers. Basically we want the pullup on whenever the ap is
|
| /openbmc/u-boot/arch/mips/mach-jz47xx/jz4780/ |
| H A D | sdram.c | 144 ((ddr_config->pullup & 0x1f) << DDRP_ZQXCR_PULLUP_IMPE_BIT) | in ddr_phy_init()
|
| /openbmc/u-boot/drivers/misc/ |
| H A D | ds4510.c | 241 U_BOOT_CMD_MKENT(pullup, 4, 0, (void *)DS4510_CMD_PULLUP, "", ""),
|
| /openbmc/linux/Documentation/spi/ |
| H A D | spi-lm70llp.rst | 65 transistor Q1 (and also a pullup, and a zener diode to D7); while the
|
| /openbmc/linux/arch/arm/boot/dts/st/ |
| H A D | ste-snowball.dts | 45 pullup-uv = <1800000>;
46 pullup-ohm = <230000>;
|
| H A D | ste-ux500-samsung-golden.dts | 52 pullup-uv = <1800000>;
53 pullup-ohm = <230000>;
|
| /openbmc/linux/drivers/usb/gadget/udc/bdc/ |
| H A D | bdc.h | 434 bool pullup; member
|
| /openbmc/linux/Documentation/devicetree/bindings/usb/ |
| H A D | msm-hsusb.txt | 76 - qcom,manual-pullup: If present, vbus is not routed to USB controller/phy
|
| /openbmc/linux/arch/arm/boot/dts/allwinner/ |
| H A D | sun6i-a31s-yones-toptech-bs1078-v2.dts | 165 /* Voltage source for I2C pullup resistors for I2C Bus 0 */
|
| /openbmc/linux/arch/arm64/boot/dts/qcom/ |
| H A D | sc7280-herobrine-herobrine-r1.dts | 134 * We'll set a pullup here just to park the line.
|
| H A D | sc7280-herobrine-crd.dts | 144 * We'll set a pullup here just to park the line.
|
| H A D | sc7280-herobrine.dtsi | 691 bias-disable; /* External pullup */
846 /* Has external pullup */
933 /* Has external pullup */
|
| /openbmc/linux/arch/arm/boot/dts/nxp/imx/ |
| H A D | imx7-tqma7.dtsi | 23 /* Configured as pullup by QSPI pin group */
|
| H A D | imx27-phytec-phycore-rdk.dts | 141 /* Add pullup to DATA line */
|
| /openbmc/u-boot/arch/mips/mach-jz47xx/include/mach/ |
| H A D | jz4780_dram.h | 448 u8 pullup; /* PHY pullup impedance */ member
|
| /openbmc/u-boot/arch/arm/dts/ |
| H A D | sun6i-a31s-yones-toptech-bs1078-v2.dts | 183 /* Voltage source for I2C pullup resistors for I2C Bus 0 */
|