| /openbmc/linux/Documentation/devicetree/bindings/net/ |
| H A D | marvell-armada-370-neta.txt | 30 higher than 'short' pool's threshold (if set) and up to MTU value.
|
| /openbmc/u-boot/doc/device-tree-bindings/adc/ |
| H A D | st,stm32-adc.txt | 10 voltage goes beyond the user-defined, higher or lower thresholds.
17 - injected conversions have higher priority, and so have the ability to
|
| /openbmc/linux/arch/powerpc/kernel/ |
| H A D | tm.S | 149 li r7, (MSR_TS_S)@higher
470 li r5, (MSR_TS_MASK)@higher
|
| /openbmc/linux/Documentation/admin-guide/mm/damon/ |
| H A D | lru_sort.rst | 32 rates that higher than a user-specified threshold) and cold pages (pages of
87 If a memory region is accessed in frequency of this or higher, DAMON_LRU_SORT
137 If free memory of the system in bytes per thousand bytes is higher than this,
|
| /openbmc/linux/Documentation/input/devices/ |
| H A D | edt-ft5x06.rst | 22 lower values indicate higher sensitivity.
|
| /openbmc/u-boot/drivers/pwm/ |
| H A D | Kconfig | 8 spends in the 'high' state, the higher the voltage. The PWM's
|
| /openbmc/openbmc/poky/meta/files/common-licenses/ |
| H A D | xinetd | 21 …riginal author, allowing xinetd as maintained by me (Rob Braun), to use the higher version numbers:
|
| /openbmc/linux/Documentation/devicetree/bindings/input/touchscreen/ |
| H A D | edt-ft5x06.yaml | 63 Note that lower values indicate higher sensitivity.
|
| /openbmc/linux/Documentation/firmware-guide/acpi/ |
| H A D | non-d0-probe.rst | 32 _DSC object evaluates to integer higher than the D state of the device,
|
| /openbmc/linux/Documentation/power/ |
| H A D | opp.rst | 27 voltage/frequency pairs that are higher.
73 SoC framework might choose to disable a higher frequency OPP to safely continue
146 higher frequency could be made available, it can use this function to
178 higher match OR operating on OPP information in the order of increasing
|
| /openbmc/linux/Documentation/arch/arm64/ |
| H A D | memory.rst | 112 higher addresses such that they are invariant to 48/52-bit VAs. Due
114 the end of the kasan shadow must also be in the higher half of the
|
| /openbmc/linux/arch/mips/include/asm/ |
| H A D | stackframe.h | 124 daddiu k1, %higher(kernelsp)
173 daddiu k1, %higher(kernelsp)
|
| /openbmc/linux/Documentation/fb/ |
| H A D | tgafb.rst | 64 When running tgafb in resolutions higher than 640x480, on switching VCs from
|
| H A D | s3fb.rst | 38 Text mode is supported even in higher resolutions, but there is limitation to
|
| /openbmc/openbmc/poky/documentation/dev-manual/ |
| H A D | intro.rst | 14 related procedures into higher-level sections. Procedures can consist of
|
| /openbmc/openbmc/poky/meta/conf/distro/include/ |
| H A D | security_flags.inc | 11 # _FORTIFY_SOURCE requires -O1 or higher, so disable in debug builds as they use
|
| /openbmc/linux/Documentation/mm/ |
| H A D | page_frags.rst | 6 which resides within a 0 or higher order compound page. Multiple
|
| /openbmc/linux/Documentation/devicetree/bindings/interrupt-controller/ |
| H A D | apple,aic.yaml | 27 higher priority)
|
| /openbmc/linux/Documentation/ABI/testing/ |
| H A D | debugfs-scmi | 17 command, advertised to have an higher-than-threshold execution
|
| /openbmc/phosphor-dbus-interfaces/yaml/xyz/openbmc_project/Smbios/ |
| H A D | MDR_V2.interface.yaml | 55 Remaining entries which are higher than index in this transfer.
|
| /openbmc/linux/Documentation/networking/ |
| H A D | dccp.rst | 58 u32 priority value as ancillary data to sendmsg(), where higher numbers indicate
59 a higher packet priority (similar to SO_PRIORITY). This ancillary data needs to
125 coverage value are also acceptable. The higher the number, the more
|
| /openbmc/linux/arch/arm/boot/dts/nxp/imx/ |
| H A D | imx6sx-softing-vining-2000.dts | 75 * unstable without higher voltages. Hence, set higher voltages here.
|
| /openbmc/linux/Documentation/admin-guide/ |
| H A D | jfs.rst | 27 is to allow for higher performance when restoring a volume
|
| /openbmc/linux/Documentation/admin-guide/media/ |
| H A D | cafe_ccic.rst | 53 better behavior with mplayer can be achieved by setting to a higher
|
| /openbmc/u-boot/doc/ |
| H A D | README.fdt-overlays | 21 Only version 4.14 or higher of the Linux kernel includes a built in version
|