/openbmc/linux/Documentation/driver-api/acpi/ |
H A D | scan_handlers.rst | 27 initialization of device nodes, such as retrieving common configuration 36 Those additional configuration tasks usually depend on the type of the hardware 60 for carrying out any additional configuration tasks related to it. It also will
|
/openbmc/linux/Documentation/devicetree/bindings/pinctrl/ |
H A D | img,pistachio-pinctrl.txt | 33 Required properties for pin configuration sub-nodes: 35 - pins: List of pins to which the configuration applies. See below for a 38 Optional properties for pin configuration sub-nodes:
|
/openbmc/linux/Documentation/networking/device_drivers/ethernet/davicom/ |
H A D | dm9000.rst | 69 This shows a typical platform device, without the optional configuration 71 the optional platform data to pass extra configuration data:: 95 the availability of an external configuration EEPROM.
|
/openbmc/linux/Documentation/userspace-api/accelerators/ |
H A D | ocxl.rst | 54 OpenCAPI relies on a PCI-like configuration space, implemented on the 64 The configuration space defines the AFU(s) that can be found on the 157 Obtains configuration information from the card, such at the size of
|
/openbmc/qemu/docs/system/arm/ |
H A D | bananapi_m2u.rst | 16 * Generic Interrupt Controller configuration 54 simply configure the kernel using the sunxi_defconfig configuration: 109 for development/testing to select the following configuration setting in U-Boot:
|
/openbmc/linux/drivers/misc/eeprom/ |
H A D | Kconfig | 102 bool "DigsyMTC display configuration EEPROMs device" 105 This option enables access to display configuration EEPROMs 108 EEPROM allowing to read/write the configuration data or to
|
/openbmc/linux/Documentation/devicetree/bindings/arm/tegra/ |
H A D | nvidia,tegra186-pmc.yaml | 70 These are pad configuration nodes. On Tegra SoCs a pad is a set of 75 configuration varies depending on the pad in question. 3.3 V and 79 Pad configurations are described with pin configuration nodes
|
/openbmc/linux/Documentation/PCI/endpoint/ |
H A D | pci-vntb-howto.rst | 12 configuration and internals of NTB using configurable endpoints see 96 A sample configuration for NTB function is given below:: 103 A sample configuration for virtual NTB driver for virtual PCI bus::
|
/openbmc/linux/arch/arm/boot/dts/nvidia/ |
H A D | tegra30-asus-nexus7-tilapia-memory-timings.dtsi | 24 nvidia,emc-configuration = < 128 nvidia,emc-configuration = < 231 nvidia,emc-configuration = <
|
/openbmc/linux/Documentation/devicetree/bindings/interrupt-controller/ |
H A D | jcore,aic.txt | 9 - reg: Memory region(s) for configuration. For SMP, there should be one
|
/openbmc/linux/drivers/net/ethernet/tehuti/ |
H A D | Kconfig | 3 # Tehuti network device configuration
|
/openbmc/linux/drivers/net/ethernet/sfc/falcon/ |
H A D | Kconfig | 22 configuration under Linux.
|
/openbmc/linux/drivers/iio/common/ssp_sensors/ |
H A D | Kconfig | 3 # SSP sensor drivers and commons configuration
|
/openbmc/openbmc/meta-openembedded/meta-oe/recipes-graphics/gtkperf/gtkperf/ |
H A D | gettext.patch | 10 ## Please disable it in the Anjuta project configuration
|
/openbmc/openbmc/poky/meta/recipes-bsp/lrzsz/lrzsz-0.12.20/ |
H A D | autotools.patch | 1 Upstream-Status: Inappropriate [configuration]
|
/openbmc/openbmc/meta-phosphor/ |
H A D | recipes.txt | 7 recipes-phosphor - Phosphor OpenBMC applications and configuration
|
/openbmc/linux/Documentation/devicetree/bindings/serial/ |
H A D | microchip,pic32-uart.txt | 10 - pinctrl-0: Phandle referencing pin configuration of the UART peripheral.
|
/openbmc/linux/Documentation/devicetree/bindings/rtc/ |
H A D | cdns,rtc.txt | 12 - ref_clk: reference 1Hz or 100Hz clock, depending on IP configuration
|
/openbmc/linux/Documentation/devicetree/bindings/reset/ |
H A D | snps,hsdk-reset.txt | 10 configuration register and second for corresponding SW reset and status bits
|
/openbmc/u-boot/drivers/scsi/ |
H A D | Kconfig | 16 which supports SCSI and SATA HDDs. For every device configuration
|
/openbmc/u-boot/board/intel/galileo/ |
H A D | Kconfig | 32 it to do different board level configuration.
|
/openbmc/phosphor-host-ipmid/ |
H A D | README.md | 16 configuration, meson automatically gets them via its wrap dependencies mentioned
|
/openbmc/qemu/tests/avocado/acpi-bits/bits-config/ |
H A D | bits-cfg.txt | 1 # BITS configuration file
|
/openbmc/openbmc/meta-openembedded/meta-webserver/recipes-webadmin/webmin/files/ |
H A D | remove-startup-option.patch | 1 Remove "start on boot" option from webmin configuration, as
|
/openbmc/qemu/configs/devices/arm-softmmu/ |
H A D | default.mak | 1 # Default configuration for arm-softmmu
|