| /openbmc/linux/drivers/usb/host/ |
| H A D | Kconfig | 357 option if your board has this chip. If unsure, say N.
370 option if your board has this chip. If unsure, say N.
631 board has this chip, and you want to use it as a host controller.
663 Enable this option if your board has this chip, and you want
675 Enable this option if your board has this chip, and you want
|
| /openbmc/linux/drivers/video/backlight/ |
| H A D | Kconfig | 152 driver. If the LCD "contrast control" on your board is wired
157 in unless the board's description says it's wired that way.
219 the PWL module of OMAP1 processors. Say Y if your board
|
| /openbmc/linux/Documentation/devicetree/bindings/phy/ |
| H A D | nvidia,tegra124-xusb-padctl.yaml | 28 settings on a per-board basis.
87 If set to "disabled", the pad will not be used on the given board. In
324 If set to "disabled", the port will not be used on the given board. In
|
| /openbmc/linux/arch/arm/boot/dts/samsung/ |
| H A D | exynos3250-rinato.dts | 3 * Samsung's Exynos3250 based Rinato board device tree source
8 * Device tree source file for Samsung's Rinato board which is based on
20 model = "Samsung Rinato board";
|
| /openbmc/linux/sound/soc/ |
| H A D | soc-core.c | 1785 const char *vendor, *product, *board; in snd_soc_set_dmi_name() local
1817 board = dmi_get_system_info(DMI_BOARD_NAME); in snd_soc_set_dmi_name()
1818 if (board && is_dmi_valid(board)) { in snd_soc_set_dmi_name()
1819 if (!product || strcasecmp(board, product)) in snd_soc_set_dmi_name()
1820 append_dmi_string(card, board); in snd_soc_set_dmi_name()
|
| /openbmc/linux/drivers/media/pci/saa7134/ |
| H A D | saa7134-i2c.c | 383 if (dev->board == SAA7134_BOARD_MD7134) in saa7134_i2c_eeprom()
|
| /openbmc/linux/arch/powerpc/boot/dts/fsl/ |
| H A D | kmcent2.dts | 65 board-control@2,0 {
|
| /openbmc/linux/Documentation/admin-guide/media/ |
| H A D | avermedia.rst | 34 There is no on-board MPEG2 decoder, which means that all MPEG2
|
| /openbmc/u-boot/drivers/usb/ |
| H A D | Kconfig | 90 board's USB port.
|
| /openbmc/u-boot/arch/arm/dts/ |
| H A D | exynos4210-trats.dts | 3 * Samsung's Exynos4210 based Trats board device tree source
|
| H A D | rk3368-sheep.dts | 11 model = "Rockchip sheep board";
|
| H A D | r8a7790-stout.dts | 3 * Device Tree Source for the Stout board
|
| H A D | sun4i-a10-a1000.dts | 90 simple-audio-card,name = "On-board SPDIF";
|
| /openbmc/u-boot/doc/ |
| H A D | README.iomux | 13 This functionality is controlled with CONFIG_CONSOLE_MUX in the board
|
| H A D | README.at91 | 154 All the board support boot from NAND flash will use the following NAND
|
| H A D | README.video | 59 When the monitor and the board power up at the same time, it may take some
|
| H A D | README.mpc83xx.ddrecc | 27 Before executing particular tests reset target board or clear status registers:
|
| /openbmc/u-boot/arch/x86/dts/ |
| H A D | crownbay.dts | 185 * Note on the Crown Bay board, Topcliff
|
| /openbmc/u-boot/doc/device-tree-bindings/spi/ |
| H A D | spi-bus.txt | 21 assumption that board specific platform code will be used to manage
|
| /openbmc/linux/Documentation/ABI/testing/ |
| H A D | sysfs-driver-hid-wiimote | 56 balance board. It provides a single line with 3 calibration
|
| /openbmc/openbmc/meta-facebook/meta-yosemitev2/recipes-bsp/u-boot/u-boot-aspeed-sdk/ |
| H A D | 0001-board-aspeed-Add-Mux-for-yosemitev2.patch | 4 Subject: [PATCH] board-aspeed-Add-Mux-for-yosemitev2
|
| /openbmc/linux/Documentation/hwmon/ |
| H A D | adm1275.rst | 65 controllers that allow a circuit board to be removed from or inserted into
|
| /openbmc/linux/Documentation/devicetree/bindings/sound/ |
| H A D | fsl-asoc-card.txt | 69 source. There're a few pre-designed board connectors:
|
| /openbmc/linux/Documentation/devicetree/bindings/memory-controllers/ |
| H A D | nvidia,tegra20-emc.yaml | 86 need to be specified, according to the board documentation.
|
| /openbmc/linux/arch/arm64/boot/dts/xilinx/ |
| H A D | zynqmp-sck-kv-g-revB.dtso | 112 * should be removed if the board has level shifter and
|