Searched hist:e4129440 (Results 1 – 3 of 3) sorted by relevance
| /openbmc/linux/net/ipv6/ |
| H A D | seg6.c | e4129440 Mon Jan 03 11:11:31 CST 2022 Andrew Lunn <andrew@lunn.ch> icmp: ICMPV6: Examine invoking packet for Segment Route Headers.
RFC8754 says:
ICMP error packets generated within the SR domain are sent to source
nodes within the SR domain. The invoking packet in the ICMP error
message may contain an SRH. Since the destination address of a packet
with an SRH changes as each segment is processed, it may not be the
destination used by the socket or application that generated the
invoking packet.
For the source of an invoking packet to process the ICMP error
message, the ultimate destination address of the IPv6 header may be
required. The following logic is used to determine the destination
address for use by protocol-error handlers.
* Walk all extension headers of the invoking IPv6 packet to the
routing extension header preceding the upper-layer header.
- If routing header is type 4 Segment Routing Header (SRH)
o The SID at Segment List[0] may be used as the destination
address of the invoking packet.
Mangle the skb so the network header points to the invoking packet
inside the ICMP packet. The seg6 helpers can then be used on the skb
to find any segment routing headers. If found, mark this fact in the
IPv6 control block of the skb, and store the offset into the packet of
the SRH. Then restore the skb back to its old state.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| H A D | icmp.c | e4129440 Mon Jan 03 11:11:31 CST 2022 Andrew Lunn <andrew@lunn.ch> icmp: ICMPV6: Examine invoking packet for Segment Route Headers.
RFC8754 says:
ICMP error packets generated within the SR domain are sent to source
nodes within the SR domain. The invoking packet in the ICMP error
message may contain an SRH. Since the destination address of a packet
with an SRH changes as each segment is processed, it may not be the
destination used by the socket or application that generated the
invoking packet.
For the source of an invoking packet to process the ICMP error
message, the ultimate destination address of the IPv6 header may be
required. The following logic is used to determine the destination
address for use by protocol-error handlers.
* Walk all extension headers of the invoking IPv6 packet to the
routing extension header preceding the upper-layer header.
- If routing header is type 4 Segment Routing Header (SRH)
o The SID at Segment List[0] may be used as the destination
address of the invoking packet.
Mangle the skb so the network header points to the invoking packet
inside the ICMP packet. The seg6 helpers can then be used on the skb
to find any segment routing headers. If found, mark this fact in the
IPv6 control block of the skb, and store the offset into the packet of
the SRH. Then restore the skb back to its old state.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| /openbmc/linux/include/linux/ |
| H A D | ipv6.h | e4129440 Mon Jan 03 11:11:31 CST 2022 Andrew Lunn <andrew@lunn.ch> icmp: ICMPV6: Examine invoking packet for Segment Route Headers.
RFC8754 says:
ICMP error packets generated within the SR domain are sent to source
nodes within the SR domain. The invoking packet in the ICMP error
message may contain an SRH. Since the destination address of a packet
with an SRH changes as each segment is processed, it may not be the
destination used by the socket or application that generated the
invoking packet.
For the source of an invoking packet to process the ICMP error
message, the ultimate destination address of the IPv6 header may be
required. The following logic is used to determine the destination
address for use by protocol-error handlers.
* Walk all extension headers of the invoking IPv6 packet to the
routing extension header preceding the upper-layer header.
- If routing header is type 4 Segment Routing Header (SRH)
o The SID at Segment List[0] may be used as the destination
address of the invoking packet.
Mangle the skb so the network header points to the invoking packet
inside the ICMP packet. The seg6 helpers can then be used on the skb
to find any segment routing headers. If found, mark this fact in the
IPv6 control block of the skb, and store the offset into the packet of
the SRH. Then restore the skb back to its old state.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|