/openbmc/u-boot/board/tqc/tqma6/ |
H A D | MAINTAINERS | a1263632 Sun Aug 31 10:47:55 CDT 2014 Masahiro Yamada <yamada.m@jp.panasonic.com> mx6: tqma6: get board support back to Kconfig build system The QS Systems TQMa6 board support was added by commit cb07d74e and lost by commit e82abaeb. Commit e82abaeb merged the IMX branch based on pre-Kconfig and the mainline based on post-Kconfig, simply deleting the boards.cfg file. As a result, some boards added just before the merge were lost. This commit adds Kconfig, defconfig, MAINTAINERS for TQMa6 board to work on the Kconfig infrastructure. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Markus Niebel <Markus.Niebel@tq-group.com> Cc: Stefano Babic <sbabic@denx.de>
|
H A D | README | cb07d74e Fri Jul 18 09:52:44 CDT 2014 Markus Niebel <Markus.Niebel@tq-group.com> Add TQ Systems TQMa6 board support This patch adds the changes to boards.cfg and the board directory under board/tqc. TQMa6 is a family of modules based on Freescale i.MX6. It consists of TQMa6Q (i.MX6 Quad), TQMa6D (i.MX6 Dual) featuring eMMC, and 1 GiB DDR3 TQMa6S (i.MX6 Solo) featuring eMMC and 512 MiB DDR3 The modules need a baseboard. Initially the MBa6x starterkit mainboard is supported. To easy support for other mainboards the functionality is splitted in one file for the module (tqma6.c) and one file for the baseboard (tqma6_ mba6). The modules can be boot from eMMC (on USDHC3) and SPI flash. The following features are supported: - MMC: eMMC on module (on USDHC3) and SD-card (on MBa6x mainboard) - Ethernet: RGMII using micrel KSZ9031 phy on MBa6x mainboard for TQMa6<x> module. The phy needs special configurations for the pad skew registers to adjust for the signal routing. Also support for standard ethernet commands and uppdate via tftp. - SPI: ECSPI1 with bootable serial flash on module and two additional chip selects on MBa6x - I2C: This patch adds support for the I2C busses on the TQMa6<x> modules (I2C3) and MBa6x baseboards (I2C1). The LM75 temperature sensors on TQMa6<x> and MBa6x are also configured. - USB: high speed host 1 on MBa6x and support for USB storage - PMIC: support for pfuze 100 on TQMa6<x> Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
|
H A D | tqma6q.cfg | cb07d74e Fri Jul 18 09:52:44 CDT 2014 Markus Niebel <Markus.Niebel@tq-group.com> Add TQ Systems TQMa6 board support This patch adds the changes to boards.cfg and the board directory under board/tqc. TQMa6 is a family of modules based on Freescale i.MX6. It consists of TQMa6Q (i.MX6 Quad), TQMa6D (i.MX6 Dual) featuring eMMC, and 1 GiB DDR3 TQMa6S (i.MX6 Solo) featuring eMMC and 512 MiB DDR3 The modules need a baseboard. Initially the MBa6x starterkit mainboard is supported. To easy support for other mainboards the functionality is splitted in one file for the module (tqma6.c) and one file for the baseboard (tqma6_ mba6). The modules can be boot from eMMC (on USDHC3) and SPI flash. The following features are supported: - MMC: eMMC on module (on USDHC3) and SD-card (on MBa6x mainboard) - Ethernet: RGMII using micrel KSZ9031 phy on MBa6x mainboard for TQMa6<x> module. The phy needs special configurations for the pad skew registers to adjust for the signal routing. Also support for standard ethernet commands and uppdate via tftp. - SPI: ECSPI1 with bootable serial flash on module and two additional chip selects on MBa6x - I2C: This patch adds support for the I2C busses on the TQMa6<x> modules (I2C3) and MBa6x baseboards (I2C1). The LM75 temperature sensors on TQMa6<x> and MBa6x are also configured. - USB: high speed host 1 on MBa6x and support for USB storage - PMIC: support for pfuze 100 on TQMa6<x> Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
|
H A D | tqma6s.cfg | cb07d74e Fri Jul 18 09:52:44 CDT 2014 Markus Niebel <Markus.Niebel@tq-group.com> Add TQ Systems TQMa6 board support This patch adds the changes to boards.cfg and the board directory under board/tqc. TQMa6 is a family of modules based on Freescale i.MX6. It consists of TQMa6Q (i.MX6 Quad), TQMa6D (i.MX6 Dual) featuring eMMC, and 1 GiB DDR3 TQMa6S (i.MX6 Solo) featuring eMMC and 512 MiB DDR3 The modules need a baseboard. Initially the MBa6x starterkit mainboard is supported. To easy support for other mainboards the functionality is splitted in one file for the module (tqma6.c) and one file for the baseboard (tqma6_ mba6). The modules can be boot from eMMC (on USDHC3) and SPI flash. The following features are supported: - MMC: eMMC on module (on USDHC3) and SD-card (on MBa6x mainboard) - Ethernet: RGMII using micrel KSZ9031 phy on MBa6x mainboard for TQMa6<x> module. The phy needs special configurations for the pad skew registers to adjust for the signal routing. Also support for standard ethernet commands and uppdate via tftp. - SPI: ECSPI1 with bootable serial flash on module and two additional chip selects on MBa6x - I2C: This patch adds support for the I2C busses on the TQMa6<x> modules (I2C3) and MBa6x baseboards (I2C1). The LM75 temperature sensors on TQMa6<x> and MBa6x are also configured. - USB: high speed host 1 on MBa6x and support for USB storage - PMIC: support for pfuze 100 on TQMa6<x> Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
|
H A D | clocks.cfg | cb07d74e Fri Jul 18 09:52:44 CDT 2014 Markus Niebel <Markus.Niebel@tq-group.com> Add TQ Systems TQMa6 board support This patch adds the changes to boards.cfg and the board directory under board/tqc. TQMa6 is a family of modules based on Freescale i.MX6. It consists of TQMa6Q (i.MX6 Quad), TQMa6D (i.MX6 Dual) featuring eMMC, and 1 GiB DDR3 TQMa6S (i.MX6 Solo) featuring eMMC and 512 MiB DDR3 The modules need a baseboard. Initially the MBa6x starterkit mainboard is supported. To easy support for other mainboards the functionality is splitted in one file for the module (tqma6.c) and one file for the baseboard (tqma6_ mba6). The modules can be boot from eMMC (on USDHC3) and SPI flash. The following features are supported: - MMC: eMMC on module (on USDHC3) and SD-card (on MBa6x mainboard) - Ethernet: RGMII using micrel KSZ9031 phy on MBa6x mainboard for TQMa6<x> module. The phy needs special configurations for the pad skew registers to adjust for the signal routing. Also support for standard ethernet commands and uppdate via tftp. - SPI: ECSPI1 with bootable serial flash on module and two additional chip selects on MBa6x - I2C: This patch adds support for the I2C busses on the TQMa6<x> modules (I2C3) and MBa6x baseboards (I2C1). The LM75 temperature sensors on TQMa6<x> and MBa6x are also configured. - USB: high speed host 1 on MBa6x and support for USB storage - PMIC: support for pfuze 100 on TQMa6<x> Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
|
H A D | Makefile | cb07d74e Fri Jul 18 09:52:44 CDT 2014 Markus Niebel <Markus.Niebel@tq-group.com> Add TQ Systems TQMa6 board support This patch adds the changes to boards.cfg and the board directory under board/tqc. TQMa6 is a family of modules based on Freescale i.MX6. It consists of TQMa6Q (i.MX6 Quad), TQMa6D (i.MX6 Dual) featuring eMMC, and 1 GiB DDR3 TQMa6S (i.MX6 Solo) featuring eMMC and 512 MiB DDR3 The modules need a baseboard. Initially the MBa6x starterkit mainboard is supported. To easy support for other mainboards the functionality is splitted in one file for the module (tqma6.c) and one file for the baseboard (tqma6_ mba6). The modules can be boot from eMMC (on USDHC3) and SPI flash. The following features are supported: - MMC: eMMC on module (on USDHC3) and SD-card (on MBa6x mainboard) - Ethernet: RGMII using micrel KSZ9031 phy on MBa6x mainboard for TQMa6<x> module. The phy needs special configurations for the pad skew registers to adjust for the signal routing. Also support for standard ethernet commands and uppdate via tftp. - SPI: ECSPI1 with bootable serial flash on module and two additional chip selects on MBa6x - I2C: This patch adds support for the I2C busses on the TQMa6<x> modules (I2C3) and MBa6x baseboards (I2C1). The LM75 temperature sensors on TQMa6<x> and MBa6x are also configured. - USB: high speed host 1 on MBa6x and support for USB storage - PMIC: support for pfuze 100 on TQMa6<x> Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
|
H A D | tqma6_bb.h | cb07d74e Fri Jul 18 09:52:44 CDT 2014 Markus Niebel <Markus.Niebel@tq-group.com> Add TQ Systems TQMa6 board support This patch adds the changes to boards.cfg and the board directory under board/tqc. TQMa6 is a family of modules based on Freescale i.MX6. It consists of TQMa6Q (i.MX6 Quad), TQMa6D (i.MX6 Dual) featuring eMMC, and 1 GiB DDR3 TQMa6S (i.MX6 Solo) featuring eMMC and 512 MiB DDR3 The modules need a baseboard. Initially the MBa6x starterkit mainboard is supported. To easy support for other mainboards the functionality is splitted in one file for the module (tqma6.c) and one file for the baseboard (tqma6_ mba6). The modules can be boot from eMMC (on USDHC3) and SPI flash. The following features are supported: - MMC: eMMC on module (on USDHC3) and SD-card (on MBa6x mainboard) - Ethernet: RGMII using micrel KSZ9031 phy on MBa6x mainboard for TQMa6<x> module. The phy needs special configurations for the pad skew registers to adjust for the signal routing. Also support for standard ethernet commands and uppdate via tftp. - SPI: ECSPI1 with bootable serial flash on module and two additional chip selects on MBa6x - I2C: This patch adds support for the I2C busses on the TQMa6<x> modules (I2C3) and MBa6x baseboards (I2C1). The LM75 temperature sensors on TQMa6<x> and MBa6x are also configured. - USB: high speed host 1 on MBa6x and support for USB storage - PMIC: support for pfuze 100 on TQMa6<x> Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
|
H A D | Kconfig | a1263632 Sun Aug 31 10:47:55 CDT 2014 Masahiro Yamada <yamada.m@jp.panasonic.com> mx6: tqma6: get board support back to Kconfig build system The QS Systems TQMa6 board support was added by commit cb07d74e and lost by commit e82abaeb. Commit e82abaeb merged the IMX branch based on pre-Kconfig and the mainline based on post-Kconfig, simply deleting the boards.cfg file. As a result, some boards added just before the merge were lost. This commit adds Kconfig, defconfig, MAINTAINERS for TQMa6 board to work on the Kconfig infrastructure. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Markus Niebel <Markus.Niebel@tq-group.com> Cc: Stefano Babic <sbabic@denx.de>
|
H A D | tqma6_mba6.c | cb07d74e Fri Jul 18 09:52:44 CDT 2014 Markus Niebel <Markus.Niebel@tq-group.com> Add TQ Systems TQMa6 board support This patch adds the changes to boards.cfg and the board directory under board/tqc. TQMa6 is a family of modules based on Freescale i.MX6. It consists of TQMa6Q (i.MX6 Quad), TQMa6D (i.MX6 Dual) featuring eMMC, and 1 GiB DDR3 TQMa6S (i.MX6 Solo) featuring eMMC and 512 MiB DDR3 The modules need a baseboard. Initially the MBa6x starterkit mainboard is supported. To easy support for other mainboards the functionality is splitted in one file for the module (tqma6.c) and one file for the baseboard (tqma6_ mba6). The modules can be boot from eMMC (on USDHC3) and SPI flash. The following features are supported: - MMC: eMMC on module (on USDHC3) and SD-card (on MBa6x mainboard) - Ethernet: RGMII using micrel KSZ9031 phy on MBa6x mainboard for TQMa6<x> module. The phy needs special configurations for the pad skew registers to adjust for the signal routing. Also support for standard ethernet commands and uppdate via tftp. - SPI: ECSPI1 with bootable serial flash on module and two additional chip selects on MBa6x - I2C: This patch adds support for the I2C busses on the TQMa6<x> modules (I2C3) and MBa6x baseboards (I2C1). The LM75 temperature sensors on TQMa6<x> and MBa6x are also configured. - USB: high speed host 1 on MBa6x and support for USB storage - PMIC: support for pfuze 100 on TQMa6<x> Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
|
H A D | tqma6.c | cb07d74e Fri Jul 18 09:52:44 CDT 2014 Markus Niebel <Markus.Niebel@tq-group.com> Add TQ Systems TQMa6 board support This patch adds the changes to boards.cfg and the board directory under board/tqc. TQMa6 is a family of modules based on Freescale i.MX6. It consists of TQMa6Q (i.MX6 Quad), TQMa6D (i.MX6 Dual) featuring eMMC, and 1 GiB DDR3 TQMa6S (i.MX6 Solo) featuring eMMC and 512 MiB DDR3 The modules need a baseboard. Initially the MBa6x starterkit mainboard is supported. To easy support for other mainboards the functionality is splitted in one file for the module (tqma6.c) and one file for the baseboard (tqma6_ mba6). The modules can be boot from eMMC (on USDHC3) and SPI flash. The following features are supported: - MMC: eMMC on module (on USDHC3) and SD-card (on MBa6x mainboard) - Ethernet: RGMII using micrel KSZ9031 phy on MBa6x mainboard for TQMa6<x> module. The phy needs special configurations for the pad skew registers to adjust for the signal routing. Also support for standard ethernet commands and uppdate via tftp. - SPI: ECSPI1 with bootable serial flash on module and two additional chip selects on MBa6x - I2C: This patch adds support for the I2C busses on the TQMa6<x> modules (I2C3) and MBa6x baseboards (I2C1). The LM75 temperature sensors on TQMa6<x> and MBa6x are also configured. - USB: high speed host 1 on MBa6x and support for USB storage - PMIC: support for pfuze 100 on TQMa6<x> Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
|
/openbmc/u-boot/configs/ |
H A D | tqma6q_mba6_spi_defconfig | a1263632 Sun Aug 31 10:47:55 CDT 2014 Masahiro Yamada <yamada.m@jp.panasonic.com> mx6: tqma6: get board support back to Kconfig build system The QS Systems TQMa6 board support was added by commit cb07d74e and lost by commit e82abaeb. Commit e82abaeb merged the IMX branch based on pre-Kconfig and the mainline based on post-Kconfig, simply deleting the boards.cfg file. As a result, some boards added just before the merge were lost. This commit adds Kconfig, defconfig, MAINTAINERS for TQMa6 board to work on the Kconfig infrastructure. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Markus Niebel <Markus.Niebel@tq-group.com> Cc: Stefano Babic <sbabic@denx.de>
|
H A D | tqma6s_mba6_mmc_defconfig | a1263632 Sun Aug 31 10:47:55 CDT 2014 Masahiro Yamada <yamada.m@jp.panasonic.com> mx6: tqma6: get board support back to Kconfig build system The QS Systems TQMa6 board support was added by commit cb07d74e and lost by commit e82abaeb. Commit e82abaeb merged the IMX branch based on pre-Kconfig and the mainline based on post-Kconfig, simply deleting the boards.cfg file. As a result, some boards added just before the merge were lost. This commit adds Kconfig, defconfig, MAINTAINERS for TQMa6 board to work on the Kconfig infrastructure. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Markus Niebel <Markus.Niebel@tq-group.com> Cc: Stefano Babic <sbabic@denx.de>
|
H A D | tqma6s_mba6_spi_defconfig | a1263632 Sun Aug 31 10:47:55 CDT 2014 Masahiro Yamada <yamada.m@jp.panasonic.com> mx6: tqma6: get board support back to Kconfig build system The QS Systems TQMa6 board support was added by commit cb07d74e and lost by commit e82abaeb. Commit e82abaeb merged the IMX branch based on pre-Kconfig and the mainline based on post-Kconfig, simply deleting the boards.cfg file. As a result, some boards added just before the merge were lost. This commit adds Kconfig, defconfig, MAINTAINERS for TQMa6 board to work on the Kconfig infrastructure. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Markus Niebel <Markus.Niebel@tq-group.com> Cc: Stefano Babic <sbabic@denx.de>
|
H A D | tqma6q_mba6_mmc_defconfig | a1263632 Sun Aug 31 10:47:55 CDT 2014 Masahiro Yamada <yamada.m@jp.panasonic.com> mx6: tqma6: get board support back to Kconfig build system The QS Systems TQMa6 board support was added by commit cb07d74e and lost by commit e82abaeb. Commit e82abaeb merged the IMX branch based on pre-Kconfig and the mainline based on post-Kconfig, simply deleting the boards.cfg file. As a result, some boards added just before the merge were lost. This commit adds Kconfig, defconfig, MAINTAINERS for TQMa6 board to work on the Kconfig infrastructure. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Markus Niebel <Markus.Niebel@tq-group.com> Cc: Stefano Babic <sbabic@denx.de>
|
/openbmc/u-boot/include/configs/ |
H A D | tqma6.h | cb07d74e Fri Jul 18 09:52:44 CDT 2014 Markus Niebel <Markus.Niebel@tq-group.com> Add TQ Systems TQMa6 board support This patch adds the changes to boards.cfg and the board directory under board/tqc. TQMa6 is a family of modules based on Freescale i.MX6. It consists of TQMa6Q (i.MX6 Quad), TQMa6D (i.MX6 Dual) featuring eMMC, and 1 GiB DDR3 TQMa6S (i.MX6 Solo) featuring eMMC and 512 MiB DDR3 The modules need a baseboard. Initially the MBa6x starterkit mainboard is supported. To easy support for other mainboards the functionality is splitted in one file for the module (tqma6.c) and one file for the baseboard (tqma6_ mba6). The modules can be boot from eMMC (on USDHC3) and SPI flash. The following features are supported: - MMC: eMMC on module (on USDHC3) and SD-card (on MBa6x mainboard) - Ethernet: RGMII using micrel KSZ9031 phy on MBa6x mainboard for TQMa6<x> module. The phy needs special configurations for the pad skew registers to adjust for the signal routing. Also support for standard ethernet commands and uppdate via tftp. - SPI: ECSPI1 with bootable serial flash on module and two additional chip selects on MBa6x - I2C: This patch adds support for the I2C busses on the TQMa6<x> modules (I2C3) and MBa6x baseboards (I2C1). The LM75 temperature sensors on TQMa6<x> and MBa6x are also configured. - USB: high speed host 1 on MBa6x and support for USB storage - PMIC: support for pfuze 100 on TQMa6<x> Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
|
/openbmc/u-boot/arch/arm/ |
H A D | Kconfig | a1263632 Sun Aug 31 10:47:55 CDT 2014 Masahiro Yamada <yamada.m@jp.panasonic.com> mx6: tqma6: get board support back to Kconfig build system The QS Systems TQMa6 board support was added by commit cb07d74e and lost by commit e82abaeb. Commit e82abaeb merged the IMX branch based on pre-Kconfig and the mainline based on post-Kconfig, simply deleting the boards.cfg file. As a result, some boards added just before the merge were lost. This commit adds Kconfig, defconfig, MAINTAINERS for TQMa6 board to work on the Kconfig infrastructure. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Markus Niebel <Markus.Niebel@tq-group.com> Cc: Stefano Babic <sbabic@denx.de>
|