Searched hist:a3a41d2f (Results 1 – 3 of 3) sorted by relevance
| /openbmc/linux/drivers/net/ethernet/ti/ |
| H A D | davinci_cpdma.h | a3a41d2f Thu Mar 15 15:15:50 CDT 2018 Grygorii Strashko <grygorii.strashko@ti.com> net: ethernet: ti: cpsw: enable vlan rx vlan offload
In VLAN_AWARE mode CPSW can insert VLAN header encapsulation word on Host
port 0 egress (RX) before the packet data if RX_VLAN_ENCAP bit is set in
CPSW_CONTROL register. VLAN header encapsulation word has following format:
HDR_PKT_Priority bits 29-31 - Header Packet VLAN prio (Highest prio: 7)
HDR_PKT_CFI bits 28 - Header Packet VLAN CFI bit.
HDR_PKT_Vid bits 27-16 - Header Packet VLAN ID
PKT_Type bits 8-9 - Packet Type. Indicates whether the packet is
VLAN-tagged, priority-tagged, or non-tagged.
00: VLAN-tagged packet
01: Reserved
10: Priority-tagged packet
11: Non-tagged packet
This feature can be used to implement TX VLAN offload in case of
VLAN-tagged packets and to insert VLAN tag in case Non-tagged packet was
received on port with PVID set. As per documentation, CPSW never modifies
packet data on Host egress (RX) and as result, without this feature
enabled, Host port will not be able to receive properly packets which
entered switch non-tagged through external Port with PVID set (when
non-tagged packet forwarded from external Port with PVID set to another
external Port - packet will be VLAN tagged properly).
Implementation details:
- on RX driver will check CPDMA status bit RX_VLAN_ENCAP BIT(19) in CPPI
descriptor to identify when VLAN header encapsulation word is present.
- PKT_Type = 0x01 or 0x02 then ignore VLAN header encapsulation word and
pass packet as is;
- if HDR_PKT_Vid = 0 then ignore VLAN header encapsulation word and pass
packet as is;
- In dual mac mode traffic is separated between ports using default port
vlans, which are not be visible to Host and so should not be reported.
Hence, check for default port vlans in dual mac mode and ignore VLAN header
encapsulation word;
- otherwise fill SKB with VLAN info using __vlan_hwaccel_put_tag();
- PKT_Type = 0x00 (VLAN-tagged) then strip out VLAN header from SKB.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
a3a41d2f Thu Mar 15 15:15:50 CDT 2018 Grygorii Strashko <grygorii.strashko@ti.com> net: ethernet: ti: cpsw: enable vlan rx vlan offload
In VLAN_AWARE mode CPSW can insert VLAN header encapsulation word on Host
port 0 egress (RX) before the packet data if RX_VLAN_ENCAP bit is set in
CPSW_CONTROL register. VLAN header encapsulation word has following format:
HDR_PKT_Priority bits 29-31 - Header Packet VLAN prio (Highest prio: 7)
HDR_PKT_CFI bits 28 - Header Packet VLAN CFI bit.
HDR_PKT_Vid bits 27-16 - Header Packet VLAN ID
PKT_Type bits 8-9 - Packet Type. Indicates whether the packet is
VLAN-tagged, priority-tagged, or non-tagged.
00: VLAN-tagged packet
01: Reserved
10: Priority-tagged packet
11: Non-tagged packet
This feature can be used to implement TX VLAN offload in case of
VLAN-tagged packets and to insert VLAN tag in case Non-tagged packet was
received on port with PVID set. As per documentation, CPSW never modifies
packet data on Host egress (RX) and as result, without this feature
enabled, Host port will not be able to receive properly packets which
entered switch non-tagged through external Port with PVID set (when
non-tagged packet forwarded from external Port with PVID set to another
external Port - packet will be VLAN tagged properly).
Implementation details:
- on RX driver will check CPDMA status bit RX_VLAN_ENCAP BIT(19) in CPPI
descriptor to identify when VLAN header encapsulation word is present.
- PKT_Type = 0x01 or 0x02 then ignore VLAN header encapsulation word and
pass packet as is;
- if HDR_PKT_Vid = 0 then ignore VLAN header encapsulation word and pass
packet as is;
- In dual mac mode traffic is separated between ports using default port
vlans, which are not be visible to Host and so should not be reported.
Hence, check for default port vlans in dual mac mode and ignore VLAN header
encapsulation word;
- otherwise fill SKB with VLAN info using __vlan_hwaccel_put_tag();
- PKT_Type = 0x00 (VLAN-tagged) then strip out VLAN header from SKB.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| H A D | davinci_cpdma.c | a3a41d2f Thu Mar 15 15:15:50 CDT 2018 Grygorii Strashko <grygorii.strashko@ti.com> net: ethernet: ti: cpsw: enable vlan rx vlan offload
In VLAN_AWARE mode CPSW can insert VLAN header encapsulation word on Host
port 0 egress (RX) before the packet data if RX_VLAN_ENCAP bit is set in
CPSW_CONTROL register. VLAN header encapsulation word has following format:
HDR_PKT_Priority bits 29-31 - Header Packet VLAN prio (Highest prio: 7)
HDR_PKT_CFI bits 28 - Header Packet VLAN CFI bit.
HDR_PKT_Vid bits 27-16 - Header Packet VLAN ID
PKT_Type bits 8-9 - Packet Type. Indicates whether the packet is
VLAN-tagged, priority-tagged, or non-tagged.
00: VLAN-tagged packet
01: Reserved
10: Priority-tagged packet
11: Non-tagged packet
This feature can be used to implement TX VLAN offload in case of
VLAN-tagged packets and to insert VLAN tag in case Non-tagged packet was
received on port with PVID set. As per documentation, CPSW never modifies
packet data on Host egress (RX) and as result, without this feature
enabled, Host port will not be able to receive properly packets which
entered switch non-tagged through external Port with PVID set (when
non-tagged packet forwarded from external Port with PVID set to another
external Port - packet will be VLAN tagged properly).
Implementation details:
- on RX driver will check CPDMA status bit RX_VLAN_ENCAP BIT(19) in CPPI
descriptor to identify when VLAN header encapsulation word is present.
- PKT_Type = 0x01 or 0x02 then ignore VLAN header encapsulation word and
pass packet as is;
- if HDR_PKT_Vid = 0 then ignore VLAN header encapsulation word and pass
packet as is;
- In dual mac mode traffic is separated between ports using default port
vlans, which are not be visible to Host and so should not be reported.
Hence, check for default port vlans in dual mac mode and ignore VLAN header
encapsulation word;
- otherwise fill SKB with VLAN info using __vlan_hwaccel_put_tag();
- PKT_Type = 0x00 (VLAN-tagged) then strip out VLAN header from SKB.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
a3a41d2f Thu Mar 15 15:15:50 CDT 2018 Grygorii Strashko <grygorii.strashko@ti.com> net: ethernet: ti: cpsw: enable vlan rx vlan offload
In VLAN_AWARE mode CPSW can insert VLAN header encapsulation word on Host
port 0 egress (RX) before the packet data if RX_VLAN_ENCAP bit is set in
CPSW_CONTROL register. VLAN header encapsulation word has following format:
HDR_PKT_Priority bits 29-31 - Header Packet VLAN prio (Highest prio: 7)
HDR_PKT_CFI bits 28 - Header Packet VLAN CFI bit.
HDR_PKT_Vid bits 27-16 - Header Packet VLAN ID
PKT_Type bits 8-9 - Packet Type. Indicates whether the packet is
VLAN-tagged, priority-tagged, or non-tagged.
00: VLAN-tagged packet
01: Reserved
10: Priority-tagged packet
11: Non-tagged packet
This feature can be used to implement TX VLAN offload in case of
VLAN-tagged packets and to insert VLAN tag in case Non-tagged packet was
received on port with PVID set. As per documentation, CPSW never modifies
packet data on Host egress (RX) and as result, without this feature
enabled, Host port will not be able to receive properly packets which
entered switch non-tagged through external Port with PVID set (when
non-tagged packet forwarded from external Port with PVID set to another
external Port - packet will be VLAN tagged properly).
Implementation details:
- on RX driver will check CPDMA status bit RX_VLAN_ENCAP BIT(19) in CPPI
descriptor to identify when VLAN header encapsulation word is present.
- PKT_Type = 0x01 or 0x02 then ignore VLAN header encapsulation word and
pass packet as is;
- if HDR_PKT_Vid = 0 then ignore VLAN header encapsulation word and pass
packet as is;
- In dual mac mode traffic is separated between ports using default port
vlans, which are not be visible to Host and so should not be reported.
Hence, check for default port vlans in dual mac mode and ignore VLAN header
encapsulation word;
- otherwise fill SKB with VLAN info using __vlan_hwaccel_put_tag();
- PKT_Type = 0x00 (VLAN-tagged) then strip out VLAN header from SKB.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| H A D | cpsw.c | a3a41d2f Thu Mar 15 15:15:50 CDT 2018 Grygorii Strashko <grygorii.strashko@ti.com> net: ethernet: ti: cpsw: enable vlan rx vlan offload
In VLAN_AWARE mode CPSW can insert VLAN header encapsulation word on Host
port 0 egress (RX) before the packet data if RX_VLAN_ENCAP bit is set in
CPSW_CONTROL register. VLAN header encapsulation word has following format:
HDR_PKT_Priority bits 29-31 - Header Packet VLAN prio (Highest prio: 7)
HDR_PKT_CFI bits 28 - Header Packet VLAN CFI bit.
HDR_PKT_Vid bits 27-16 - Header Packet VLAN ID
PKT_Type bits 8-9 - Packet Type. Indicates whether the packet is
VLAN-tagged, priority-tagged, or non-tagged.
00: VLAN-tagged packet
01: Reserved
10: Priority-tagged packet
11: Non-tagged packet
This feature can be used to implement TX VLAN offload in case of
VLAN-tagged packets and to insert VLAN tag in case Non-tagged packet was
received on port with PVID set. As per documentation, CPSW never modifies
packet data on Host egress (RX) and as result, without this feature
enabled, Host port will not be able to receive properly packets which
entered switch non-tagged through external Port with PVID set (when
non-tagged packet forwarded from external Port with PVID set to another
external Port - packet will be VLAN tagged properly).
Implementation details:
- on RX driver will check CPDMA status bit RX_VLAN_ENCAP BIT(19) in CPPI
descriptor to identify when VLAN header encapsulation word is present.
- PKT_Type = 0x01 or 0x02 then ignore VLAN header encapsulation word and
pass packet as is;
- if HDR_PKT_Vid = 0 then ignore VLAN header encapsulation word and pass
packet as is;
- In dual mac mode traffic is separated between ports using default port
vlans, which are not be visible to Host and so should not be reported.
Hence, check for default port vlans in dual mac mode and ignore VLAN header
encapsulation word;
- otherwise fill SKB with VLAN info using __vlan_hwaccel_put_tag();
- PKT_Type = 0x00 (VLAN-tagged) then strip out VLAN header from SKB.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
a3a41d2f Thu Mar 15 15:15:50 CDT 2018 Grygorii Strashko <grygorii.strashko@ti.com> net: ethernet: ti: cpsw: enable vlan rx vlan offload
In VLAN_AWARE mode CPSW can insert VLAN header encapsulation word on Host
port 0 egress (RX) before the packet data if RX_VLAN_ENCAP bit is set in
CPSW_CONTROL register. VLAN header encapsulation word has following format:
HDR_PKT_Priority bits 29-31 - Header Packet VLAN prio (Highest prio: 7)
HDR_PKT_CFI bits 28 - Header Packet VLAN CFI bit.
HDR_PKT_Vid bits 27-16 - Header Packet VLAN ID
PKT_Type bits 8-9 - Packet Type. Indicates whether the packet is
VLAN-tagged, priority-tagged, or non-tagged.
00: VLAN-tagged packet
01: Reserved
10: Priority-tagged packet
11: Non-tagged packet
This feature can be used to implement TX VLAN offload in case of
VLAN-tagged packets and to insert VLAN tag in case Non-tagged packet was
received on port with PVID set. As per documentation, CPSW never modifies
packet data on Host egress (RX) and as result, without this feature
enabled, Host port will not be able to receive properly packets which
entered switch non-tagged through external Port with PVID set (when
non-tagged packet forwarded from external Port with PVID set to another
external Port - packet will be VLAN tagged properly).
Implementation details:
- on RX driver will check CPDMA status bit RX_VLAN_ENCAP BIT(19) in CPPI
descriptor to identify when VLAN header encapsulation word is present.
- PKT_Type = 0x01 or 0x02 then ignore VLAN header encapsulation word and
pass packet as is;
- if HDR_PKT_Vid = 0 then ignore VLAN header encapsulation word and pass
packet as is;
- In dual mac mode traffic is separated between ports using default port
vlans, which are not be visible to Host and so should not be reported.
Hence, check for default port vlans in dual mac mode and ignore VLAN header
encapsulation word;
- otherwise fill SKB with VLAN info using __vlan_hwaccel_put_tag();
- PKT_Type = 0x00 (VLAN-tagged) then strip out VLAN header from SKB.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|