Searched hist:"9 bcf15f7" (Results 1 – 1 of 1) sorted by relevance
| /openbmc/linux/drivers/iio/adc/ |
| H A D | axp288_adc.c | 9bcf15f7 Sat Jan 05 12:36:18 CST 2019 Hans de Goede <hdegoede@redhat.com> iio: adc: axp288: Fix TS-pin handling
Prior to this commit there were 3 issues with our handling of the TS-pin:
1) There are 2 ways how the firmware can disable monitoring of the TS-pin
for designs which do not have a temperature-sensor for the battery:
a) Clearing bit 0 of the AXP20X_ADC_EN1 register
b) Setting bit 2 of the AXP288_ADC_TS_PIN_CTRL monitoring
Prior to this commit we were unconditionally setting both bits to the
value used on devices with a TS. This causes the temperature protection to
kick in on devices without a TS, such as the Jumper ezbook v2, causing
them to not charge under Linux.
This commit fixes this by using regmap_update_bits when updating these 2
registers, leaving the 2 mentioned bits alone.
The next 2 problems are related to our handling of the current-source
for the TS-pin. The current-source used for the battery temp-sensor (TS)
is shared with the GPADC. For proper fuel-gauge and charger operation the
TS current-source needs to be permanently on. But to read the GPADC we
need to temporary switch the TS current-source to ondemand, so that the
GPADC can use it, otherwise we will always read an all 0 value.
2) Problem 2 is we were writing hardcoded values to the ADC TS pin-ctrl
register, overwriting various other unrelated bits. Specifically we were
overwriting the current-source setting for the TS and GPIO0 pins, forcing
it to 80ųA independent of its original setting. On a Chuwi Vi10 tablet
this was causing us to get a too high adc value (due to a too high
current-source) resulting in the following errors being logged:
ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.SXP1._TMP, AE_ERROR
This commit fixes this by using regmap_update_bits to change only the
relevant bits.
3) After reading the GPADC channel we were unconditionally enabling the
TS current-source even on devices where the TS-pin is not used and the
current-source thus was off before axp288_adc_read_raw call.
This commit fixes this by making axp288_adc_set_ts a nop on devices where
the ADC is not enabled for the TS-pin.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1610545
Fixes: 3091141d7803 ("iio: adc: axp288: Fix the GPADC pin ...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
9bcf15f7 Sat Jan 05 12:36:18 CST 2019 Hans de Goede <hdegoede@redhat.com> iio: adc: axp288: Fix TS-pin handling
Prior to this commit there were 3 issues with our handling of the TS-pin:
1) There are 2 ways how the firmware can disable monitoring of the TS-pin
for designs which do not have a temperature-sensor for the battery:
a) Clearing bit 0 of the AXP20X_ADC_EN1 register
b) Setting bit 2 of the AXP288_ADC_TS_PIN_CTRL monitoring
Prior to this commit we were unconditionally setting both bits to the
value used on devices with a TS. This causes the temperature protection to
kick in on devices without a TS, such as the Jumper ezbook v2, causing
them to not charge under Linux.
This commit fixes this by using regmap_update_bits when updating these 2
registers, leaving the 2 mentioned bits alone.
The next 2 problems are related to our handling of the current-source
for the TS-pin. The current-source used for the battery temp-sensor (TS)
is shared with the GPADC. For proper fuel-gauge and charger operation the
TS current-source needs to be permanently on. But to read the GPADC we
need to temporary switch the TS current-source to ondemand, so that the
GPADC can use it, otherwise we will always read an all 0 value.
2) Problem 2 is we were writing hardcoded values to the ADC TS pin-ctrl
register, overwriting various other unrelated bits. Specifically we were
overwriting the current-source setting for the TS and GPIO0 pins, forcing
it to 80ųA independent of its original setting. On a Chuwi Vi10 tablet
this was causing us to get a too high adc value (due to a too high
current-source) resulting in the following errors being logged:
ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.SXP1._TMP, AE_ERROR
This commit fixes this by using regmap_update_bits to change only the
relevant bits.
3) After reading the GPADC channel we were unconditionally enabling the
TS current-source even on devices where the TS-pin is not used and the
current-source thus was off before axp288_adc_read_raw call.
This commit fixes this by making axp288_adc_set_ts a nop on devices where
the ADC is not enabled for the TS-pin.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1610545
Fixes: 3091141d7803 ("iio: adc: axp288: Fix the GPADC pin ...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|