Searched hist:"6 cb57c67" (Results 1 – 2 of 2) sorted by relevance
| /openbmc/linux/drivers/clk/meson/ |
| H A D | meson8b.h | 6cb57c67 Sun Dec 02 15:42:20 CST 2018 Martin Blumenstingl <martin.blumenstingl@googlemail.com> clk: meson: meson8b: add the read-only video clock trees
Add all clocks to give us the final video clocks within the Meson8,
Meson8b and Meson8m2 SoCs. The final video clocks are:
- cts_enct
- cts_encl
- cts_encp
- cts_enci
- cts_vdac0
- hdmi_tx_pixel
- hdmi_sys
Add multiple clocks in between which are needed to implement these
clocks:
- Opposed to GXBB there is no pre-multiplier for the PLL input. The
assumption here is that the multiplier is required to achieve the HDMI
2.0 clock rates (which are up to twice the rate of the HDMI 1.4
rates).
- The main PLL is called "HDMI PLL" or "HPLL" in the datasheet. Rename
our existing "vid_pll_dco" to "hdmi_pll_dco". The actual VID_PLL clock
also exists further down the tree.
- Rename the existing "vid_pll" clock (which is the OD divider at
HHI_VID_PLL_CNTL[17:16]) to "hdmi_pll_lvds_out" to match the naming
from the datasheet.
- Add the second OD divider called "hdmi_pll_hdmi_out" at
HHI_VID_PLL_CNTL[19:18].
- Add the "vid_pll_in_sel" which can choose between "hdmi_pll_dco" and
another parent. However, the second parent is not use on Amlogic's
3.10 kernel for HDMI or CVBS output so just leave a TODO in the code.
- Add the "vid_pll_in_en" which is located after "vid_pll_in_sel"
according to the datasheet.
- Add "vid_pll_pre_div" which is used for divide-by-5 and divide-by-6 in
Amlogic's 3.10 kernel sources.
- Add "vid_pll_post_div" which divides the output of "vid_pll_pre_div"
further down. The Amlogic 3.10 kernel configures this as divide-by-2
with "vid_pll_pre_div" being configured as divide-by-5 to achieve a
total divider of 10.
- Add the real "vid_pll" clock which selects between "vid_pll_pre_div",
"vid_pll_post_div" and a third "vid_pll_pre_div_mult7_div2" (which is
"vid_pll_pre_div" divided by 3.5). The latter is not supported yet
because it's not used in Amlogic's 3.10 kernel. The "vid_pll" clock
rate can also be measured by clkmsr to check whether this
implementation is correct.
- Add "vid_pll_final_div" which is a post-divider for "vid_pll" and it's
used as input for "vclk" and "vclk2"
- Add the two symmetric "vclk" and "vclk" clock trees, each with a
divide-by-1, divide-by-2, divide-by-4, divide-by-6 and divide-by-12
clock and a divider for each clock.
- Add the "cts_enct", "cts_encp" and "hdmi_tx_pixel" clocks which each
have their own gate and can select between any of the five "vclk"
dividers.
- Add the "cts_encl" and "cts_vdac0" clocks which each have their own
gate and can select between any of the five "vclk2" dividers.
The "hdmi_sys" clock is a different than these video clocks. It takes
"xtal" as input (there are three more but unknown parents). Add this
clock as well as it's used by the HDMI controller. Amlogic's 3.10 kernel
always configures this as "xtal divided by 1", so we can ignore the
other parents for now.
This was tested on Meson8b and Meson8m2 boards by comparing the common
clock framework output with the clock measurer output. The following
video modes were first set in u-boot (by running "video dev open $mode")
before booting Linux:
4K2K30HZ (only supported by Meson8m2, not tested on Meson8b):
- vid_pll: 297000000Hz
- cts_encp: 297000000Hz
- hdmi_tx_pixel: 297000000Hz
1080P:
- vid_pll: 148500000Hz
- cts_encp: 148500000Hz
- hdmi_tx_pixel: 148500000Hz
720P:
- vid_pll: 148500000Hz
- cts_encp: 148500000Hz
- hdmi_tx_pixel: 74250000Hz
480P:
- vid_pll: 216000000Hz
- cts_encp: 54000000Hz
- hdmi_tx_pixel: 27000000Hz
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181202214220.7715-4-martin.blumenstingl@googlemail.com
6cb57c67 Sun Dec 02 15:42:20 CST 2018 Martin Blumenstingl <martin.blumenstingl@googlemail.com> clk: meson: meson8b: add the read-only video clock trees
Add all clocks to give us the final video clocks within the Meson8,
Meson8b and Meson8m2 SoCs. The final video clocks are:
- cts_enct
- cts_encl
- cts_encp
- cts_enci
- cts_vdac0
- hdmi_tx_pixel
- hdmi_sys
Add multiple clocks in between which are needed to implement these
clocks:
- Opposed to GXBB there is no pre-multiplier for the PLL input. The
assumption here is that the multiplier is required to achieve the HDMI
2.0 clock rates (which are up to twice the rate of the HDMI 1.4
rates).
- The main PLL is called "HDMI PLL" or "HPLL" in the datasheet. Rename
our existing "vid_pll_dco" to "hdmi_pll_dco". The actual VID_PLL clock
also exists further down the tree.
- Rename the existing "vid_pll" clock (which is the OD divider at
HHI_VID_PLL_CNTL[17:16]) to "hdmi_pll_lvds_out" to match the naming
from the datasheet.
- Add the second OD divider called "hdmi_pll_hdmi_out" at
HHI_VID_PLL_CNTL[19:18].
- Add the "vid_pll_in_sel" which can choose between "hdmi_pll_dco" and
another parent. However, the second parent is not use on Amlogic's
3.10 kernel for HDMI or CVBS output so just leave a TODO in the code.
- Add the "vid_pll_in_en" which is located after "vid_pll_in_sel"
according to the datasheet.
- Add "vid_pll_pre_div" which is used for divide-by-5 and divide-by-6 in
Amlogic's 3.10 kernel sources.
- Add "vid_pll_post_div" which divides the output of "vid_pll_pre_div"
further down. The Amlogic 3.10 kernel configures this as divide-by-2
with "vid_pll_pre_div" being configured as divide-by-5 to achieve a
total divider of 10.
- Add the real "vid_pll" clock which selects between "vid_pll_pre_div",
"vid_pll_post_div" and a third "vid_pll_pre_div_mult7_div2" (which is
"vid_pll_pre_div" divided by 3.5). The latter is not supported yet
because it's not used in Amlogic's 3.10 kernel. The "vid_pll" clock
rate can also be measured by clkmsr to check whether this
implementation is correct.
- Add "vid_pll_final_div" which is a post-divider for "vid_pll" and it's
used as input for "vclk" and "vclk2"
- Add the two symmetric "vclk" and "vclk" clock trees, each with a
divide-by-1, divide-by-2, divide-by-4, divide-by-6 and divide-by-12
clock and a divider for each clock.
- Add the "cts_enct", "cts_encp" and "hdmi_tx_pixel" clocks which each
have their own gate and can select between any of the five "vclk"
dividers.
- Add the "cts_encl" and "cts_vdac0" clocks which each have their own
gate and can select between any of the five "vclk2" dividers.
The "hdmi_sys" clock is a different than these video clocks. It takes
"xtal" as input (there are three more but unknown parents). Add this
clock as well as it's used by the HDMI controller. Amlogic's 3.10 kernel
always configures this as "xtal divided by 1", so we can ignore the
other parents for now.
This was tested on Meson8b and Meson8m2 boards by comparing the common
clock framework output with the clock measurer output. The following
video modes were first set in u-boot (by running "video dev open $mode")
before booting Linux:
4K2K30HZ (only supported by Meson8m2, not tested on Meson8b):
- vid_pll: 297000000Hz
- cts_encp: 297000000Hz
- hdmi_tx_pixel: 297000000Hz
1080P:
- vid_pll: 148500000Hz
- cts_encp: 148500000Hz
- hdmi_tx_pixel: 148500000Hz
720P:
- vid_pll: 148500000Hz
- cts_encp: 148500000Hz
- hdmi_tx_pixel: 74250000Hz
480P:
- vid_pll: 216000000Hz
- cts_encp: 54000000Hz
- hdmi_tx_pixel: 27000000Hz
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181202214220.7715-4-martin.blumenstingl@googlemail.com
|
| H A D | meson8b.c | 6cb57c67 Sun Dec 02 15:42:20 CST 2018 Martin Blumenstingl <martin.blumenstingl@googlemail.com> clk: meson: meson8b: add the read-only video clock trees
Add all clocks to give us the final video clocks within the Meson8,
Meson8b and Meson8m2 SoCs. The final video clocks are:
- cts_enct
- cts_encl
- cts_encp
- cts_enci
- cts_vdac0
- hdmi_tx_pixel
- hdmi_sys
Add multiple clocks in between which are needed to implement these
clocks:
- Opposed to GXBB there is no pre-multiplier for the PLL input. The
assumption here is that the multiplier is required to achieve the HDMI
2.0 clock rates (which are up to twice the rate of the HDMI 1.4
rates).
- The main PLL is called "HDMI PLL" or "HPLL" in the datasheet. Rename
our existing "vid_pll_dco" to "hdmi_pll_dco". The actual VID_PLL clock
also exists further down the tree.
- Rename the existing "vid_pll" clock (which is the OD divider at
HHI_VID_PLL_CNTL[17:16]) to "hdmi_pll_lvds_out" to match the naming
from the datasheet.
- Add the second OD divider called "hdmi_pll_hdmi_out" at
HHI_VID_PLL_CNTL[19:18].
- Add the "vid_pll_in_sel" which can choose between "hdmi_pll_dco" and
another parent. However, the second parent is not use on Amlogic's
3.10 kernel for HDMI or CVBS output so just leave a TODO in the code.
- Add the "vid_pll_in_en" which is located after "vid_pll_in_sel"
according to the datasheet.
- Add "vid_pll_pre_div" which is used for divide-by-5 and divide-by-6 in
Amlogic's 3.10 kernel sources.
- Add "vid_pll_post_div" which divides the output of "vid_pll_pre_div"
further down. The Amlogic 3.10 kernel configures this as divide-by-2
with "vid_pll_pre_div" being configured as divide-by-5 to achieve a
total divider of 10.
- Add the real "vid_pll" clock which selects between "vid_pll_pre_div",
"vid_pll_post_div" and a third "vid_pll_pre_div_mult7_div2" (which is
"vid_pll_pre_div" divided by 3.5). The latter is not supported yet
because it's not used in Amlogic's 3.10 kernel. The "vid_pll" clock
rate can also be measured by clkmsr to check whether this
implementation is correct.
- Add "vid_pll_final_div" which is a post-divider for "vid_pll" and it's
used as input for "vclk" and "vclk2"
- Add the two symmetric "vclk" and "vclk" clock trees, each with a
divide-by-1, divide-by-2, divide-by-4, divide-by-6 and divide-by-12
clock and a divider for each clock.
- Add the "cts_enct", "cts_encp" and "hdmi_tx_pixel" clocks which each
have their own gate and can select between any of the five "vclk"
dividers.
- Add the "cts_encl" and "cts_vdac0" clocks which each have their own
gate and can select between any of the five "vclk2" dividers.
The "hdmi_sys" clock is a different than these video clocks. It takes
"xtal" as input (there are three more but unknown parents). Add this
clock as well as it's used by the HDMI controller. Amlogic's 3.10 kernel
always configures this as "xtal divided by 1", so we can ignore the
other parents for now.
This was tested on Meson8b and Meson8m2 boards by comparing the common
clock framework output with the clock measurer output. The following
video modes were first set in u-boot (by running "video dev open $mode")
before booting Linux:
4K2K30HZ (only supported by Meson8m2, not tested on Meson8b):
- vid_pll: 297000000Hz
- cts_encp: 297000000Hz
- hdmi_tx_pixel: 297000000Hz
1080P:
- vid_pll: 148500000Hz
- cts_encp: 148500000Hz
- hdmi_tx_pixel: 148500000Hz
720P:
- vid_pll: 148500000Hz
- cts_encp: 148500000Hz
- hdmi_tx_pixel: 74250000Hz
480P:
- vid_pll: 216000000Hz
- cts_encp: 54000000Hz
- hdmi_tx_pixel: 27000000Hz
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181202214220.7715-4-martin.blumenstingl@googlemail.com
6cb57c67 Sun Dec 02 15:42:20 CST 2018 Martin Blumenstingl <martin.blumenstingl@googlemail.com> clk: meson: meson8b: add the read-only video clock trees
Add all clocks to give us the final video clocks within the Meson8,
Meson8b and Meson8m2 SoCs. The final video clocks are:
- cts_enct
- cts_encl
- cts_encp
- cts_enci
- cts_vdac0
- hdmi_tx_pixel
- hdmi_sys
Add multiple clocks in between which are needed to implement these
clocks:
- Opposed to GXBB there is no pre-multiplier for the PLL input. The
assumption here is that the multiplier is required to achieve the HDMI
2.0 clock rates (which are up to twice the rate of the HDMI 1.4
rates).
- The main PLL is called "HDMI PLL" or "HPLL" in the datasheet. Rename
our existing "vid_pll_dco" to "hdmi_pll_dco". The actual VID_PLL clock
also exists further down the tree.
- Rename the existing "vid_pll" clock (which is the OD divider at
HHI_VID_PLL_CNTL[17:16]) to "hdmi_pll_lvds_out" to match the naming
from the datasheet.
- Add the second OD divider called "hdmi_pll_hdmi_out" at
HHI_VID_PLL_CNTL[19:18].
- Add the "vid_pll_in_sel" which can choose between "hdmi_pll_dco" and
another parent. However, the second parent is not use on Amlogic's
3.10 kernel for HDMI or CVBS output so just leave a TODO in the code.
- Add the "vid_pll_in_en" which is located after "vid_pll_in_sel"
according to the datasheet.
- Add "vid_pll_pre_div" which is used for divide-by-5 and divide-by-6 in
Amlogic's 3.10 kernel sources.
- Add "vid_pll_post_div" which divides the output of "vid_pll_pre_div"
further down. The Amlogic 3.10 kernel configures this as divide-by-2
with "vid_pll_pre_div" being configured as divide-by-5 to achieve a
total divider of 10.
- Add the real "vid_pll" clock which selects between "vid_pll_pre_div",
"vid_pll_post_div" and a third "vid_pll_pre_div_mult7_div2" (which is
"vid_pll_pre_div" divided by 3.5). The latter is not supported yet
because it's not used in Amlogic's 3.10 kernel. The "vid_pll" clock
rate can also be measured by clkmsr to check whether this
implementation is correct.
- Add "vid_pll_final_div" which is a post-divider for "vid_pll" and it's
used as input for "vclk" and "vclk2"
- Add the two symmetric "vclk" and "vclk" clock trees, each with a
divide-by-1, divide-by-2, divide-by-4, divide-by-6 and divide-by-12
clock and a divider for each clock.
- Add the "cts_enct", "cts_encp" and "hdmi_tx_pixel" clocks which each
have their own gate and can select between any of the five "vclk"
dividers.
- Add the "cts_encl" and "cts_vdac0" clocks which each have their own
gate and can select between any of the five "vclk2" dividers.
The "hdmi_sys" clock is a different than these video clocks. It takes
"xtal" as input (there are three more but unknown parents). Add this
clock as well as it's used by the HDMI controller. Amlogic's 3.10 kernel
always configures this as "xtal divided by 1", so we can ignore the
other parents for now.
This was tested on Meson8b and Meson8m2 boards by comparing the common
clock framework output with the clock measurer output. The following
video modes were first set in u-boot (by running "video dev open $mode")
before booting Linux:
4K2K30HZ (only supported by Meson8m2, not tested on Meson8b):
- vid_pll: 297000000Hz
- cts_encp: 297000000Hz
- hdmi_tx_pixel: 297000000Hz
1080P:
- vid_pll: 148500000Hz
- cts_encp: 148500000Hz
- hdmi_tx_pixel: 148500000Hz
720P:
- vid_pll: 148500000Hz
- cts_encp: 148500000Hz
- hdmi_tx_pixel: 74250000Hz
480P:
- vid_pll: 216000000Hz
- cts_encp: 54000000Hz
- hdmi_tx_pixel: 27000000Hz
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lkml.kernel.org/r/20181202214220.7715-4-martin.blumenstingl@googlemail.com
|