Searched hist:"3 e5f3bcd" (Results 1 – 3 of 3) sorted by relevance
| /openbmc/qemu/migration/ |
| H A D | trace-events | 3e5f3bcd Mon Oct 30 11:33:46 CDT 2023 Peter Xu <peterx@redhat.com> migration: Add tracepoints for downtime checkpoints
This patch is inspired by Joao Martin's patch here:
https://lore.kernel.org/r/20230926161841.98464-1-joao.m.martins@oracle.com
Add tracepoints for major downtime checkpoints on both src and dst. They
share the same tracepoint with a string showing its stage.
Besides the checkpoints in the previous patch, this patch also added
destination checkpoints.
On src, we have these checkpoints added:
- src-downtime-start: right before vm stops on src
- src-vm-stopped: after vm is fully stopped
- src-iterable-saved: after all iterables saved (END sections)
- src-non-iterable-saved: after all non-iterable saved (FULL sections)
- src-downtime-stop: migration fully completed
On dst, we have these checkpoints added:
- dst-precopy-loadvm-completes: after loadvm all done for precopy
- dst-precopy-bh-*: record BH steps to resume VM for precopy
- dst-postcopy-bh-*: record BH steps to resume VM for postcopy
On dst side, we don't have a good way to trace total time consumed by
iterable or non-iterable for now. We can mark it by 1st time receiving a
FULL / END section, but rather than that let's just rely on the other
tracepoints added for vmstates to back up the information.
With this patch, one can enable "vmstate_downtime*" tracepoints and it'll
enable all tracepoints for downtime measurements necessary.
Drop loadvm_postcopy_handle_run_bh() tracepoint alongside, because they
service the same purpose, which was only for postcopy. We then have
unified prefix for all downtime relevant tracepoints.
Co-developed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20231030163346.765724-6-peterx@redhat.com>
|
| H A D | savevm.c | 3e5f3bcd Mon Oct 30 11:33:46 CDT 2023 Peter Xu <peterx@redhat.com> migration: Add tracepoints for downtime checkpoints
This patch is inspired by Joao Martin's patch here:
https://lore.kernel.org/r/20230926161841.98464-1-joao.m.martins@oracle.com
Add tracepoints for major downtime checkpoints on both src and dst. They
share the same tracepoint with a string showing its stage.
Besides the checkpoints in the previous patch, this patch also added
destination checkpoints.
On src, we have these checkpoints added:
- src-downtime-start: right before vm stops on src
- src-vm-stopped: after vm is fully stopped
- src-iterable-saved: after all iterables saved (END sections)
- src-non-iterable-saved: after all non-iterable saved (FULL sections)
- src-downtime-stop: migration fully completed
On dst, we have these checkpoints added:
- dst-precopy-loadvm-completes: after loadvm all done for precopy
- dst-precopy-bh-*: record BH steps to resume VM for precopy
- dst-postcopy-bh-*: record BH steps to resume VM for postcopy
On dst side, we don't have a good way to trace total time consumed by
iterable or non-iterable for now. We can mark it by 1st time receiving a
FULL / END section, but rather than that let's just rely on the other
tracepoints added for vmstates to back up the information.
With this patch, one can enable "vmstate_downtime*" tracepoints and it'll
enable all tracepoints for downtime measurements necessary.
Drop loadvm_postcopy_handle_run_bh() tracepoint alongside, because they
service the same purpose, which was only for postcopy. We then have
unified prefix for all downtime relevant tracepoints.
Co-developed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20231030163346.765724-6-peterx@redhat.com>
|
| H A D | migration.c | 3e5f3bcd Mon Oct 30 11:33:46 CDT 2023 Peter Xu <peterx@redhat.com> migration: Add tracepoints for downtime checkpoints
This patch is inspired by Joao Martin's patch here:
https://lore.kernel.org/r/20230926161841.98464-1-joao.m.martins@oracle.com
Add tracepoints for major downtime checkpoints on both src and dst. They
share the same tracepoint with a string showing its stage.
Besides the checkpoints in the previous patch, this patch also added
destination checkpoints.
On src, we have these checkpoints added:
- src-downtime-start: right before vm stops on src
- src-vm-stopped: after vm is fully stopped
- src-iterable-saved: after all iterables saved (END sections)
- src-non-iterable-saved: after all non-iterable saved (FULL sections)
- src-downtime-stop: migration fully completed
On dst, we have these checkpoints added:
- dst-precopy-loadvm-completes: after loadvm all done for precopy
- dst-precopy-bh-*: record BH steps to resume VM for precopy
- dst-postcopy-bh-*: record BH steps to resume VM for postcopy
On dst side, we don't have a good way to trace total time consumed by
iterable or non-iterable for now. We can mark it by 1st time receiving a
FULL / END section, but rather than that let's just rely on the other
tracepoints added for vmstates to back up the information.
With this patch, one can enable "vmstate_downtime*" tracepoints and it'll
enable all tracepoints for downtime measurements necessary.
Drop loadvm_postcopy_handle_run_bh() tracepoint alongside, because they
service the same purpose, which was only for postcopy. We then have
unified prefix for all downtime relevant tracepoints.
Co-developed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Message-ID: <20231030163346.765724-6-peterx@redhat.com>
|