Searched hist:"23402 bdd" (Results 1 – 3 of 3) sorted by relevance
| /openbmc/linux/drivers/net/ethernet/freescale/ |
| H A D | gianfar_ethtool.c | 23402bdd Mon Aug 12 05:53:26 CDT 2013 Claudiu Manoil <claudiu.manoil@freescale.com> gianfar: Add flow control support
eTSEC has Rx and Tx flow control capabilities that may be enabled
through MACCFG1[Rx_Flow, Tx_Flow] bits. These bits must not be set
however when eTSEC is operated in Half-Duplex mode. Unfortunately,
the driver currently sets these bits unconditionally.
This patch adds the proper handling of the PAUSE frame capability
register bits by implementing the ethtool -A interface. When pause
autoneg is enabled, the controller uses the phy's capability to
negotiate PAUSE frame settings with the link partner and reconfigures
its Rx_Flow and Tx_Flow settings to match the capabilities of the
link partner. If pause autoneg is off, the PAUSE frame generation
may be forced manually (ethtool -A). Flow control is disabled by
default now.
This implementation is inspired by the tg3 driver.
Signed-off-by: Lutz Jaenicke <ljaenicke@innominate.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
23402bdd Mon Aug 12 05:53:26 CDT 2013 Claudiu Manoil <claudiu.manoil@freescale.com> gianfar: Add flow control support
eTSEC has Rx and Tx flow control capabilities that may be enabled
through MACCFG1[Rx_Flow, Tx_Flow] bits. These bits must not be set
however when eTSEC is operated in Half-Duplex mode. Unfortunately,
the driver currently sets these bits unconditionally.
This patch adds the proper handling of the PAUSE frame capability
register bits by implementing the ethtool -A interface. When pause
autoneg is enabled, the controller uses the phy's capability to
negotiate PAUSE frame settings with the link partner and reconfigures
its Rx_Flow and Tx_Flow settings to match the capabilities of the
link partner. If pause autoneg is off, the PAUSE frame generation
may be forced manually (ethtool -A). Flow control is disabled by
default now.
This implementation is inspired by the tg3 driver.
Signed-off-by: Lutz Jaenicke <ljaenicke@innominate.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| H A D | gianfar.h | 23402bdd Mon Aug 12 05:53:26 CDT 2013 Claudiu Manoil <claudiu.manoil@freescale.com> gianfar: Add flow control support
eTSEC has Rx and Tx flow control capabilities that may be enabled
through MACCFG1[Rx_Flow, Tx_Flow] bits. These bits must not be set
however when eTSEC is operated in Half-Duplex mode. Unfortunately,
the driver currently sets these bits unconditionally.
This patch adds the proper handling of the PAUSE frame capability
register bits by implementing the ethtool -A interface. When pause
autoneg is enabled, the controller uses the phy's capability to
negotiate PAUSE frame settings with the link partner and reconfigures
its Rx_Flow and Tx_Flow settings to match the capabilities of the
link partner. If pause autoneg is off, the PAUSE frame generation
may be forced manually (ethtool -A). Flow control is disabled by
default now.
This implementation is inspired by the tg3 driver.
Signed-off-by: Lutz Jaenicke <ljaenicke@innominate.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
23402bdd Mon Aug 12 05:53:26 CDT 2013 Claudiu Manoil <claudiu.manoil@freescale.com> gianfar: Add flow control support
eTSEC has Rx and Tx flow control capabilities that may be enabled
through MACCFG1[Rx_Flow, Tx_Flow] bits. These bits must not be set
however when eTSEC is operated in Half-Duplex mode. Unfortunately,
the driver currently sets these bits unconditionally.
This patch adds the proper handling of the PAUSE frame capability
register bits by implementing the ethtool -A interface. When pause
autoneg is enabled, the controller uses the phy's capability to
negotiate PAUSE frame settings with the link partner and reconfigures
its Rx_Flow and Tx_Flow settings to match the capabilities of the
link partner. If pause autoneg is off, the PAUSE frame generation
may be forced manually (ethtool -A). Flow control is disabled by
default now.
This implementation is inspired by the tg3 driver.
Signed-off-by: Lutz Jaenicke <ljaenicke@innominate.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| H A D | gianfar.c | 23402bdd Mon Aug 12 05:53:26 CDT 2013 Claudiu Manoil <claudiu.manoil@freescale.com> gianfar: Add flow control support
eTSEC has Rx and Tx flow control capabilities that may be enabled
through MACCFG1[Rx_Flow, Tx_Flow] bits. These bits must not be set
however when eTSEC is operated in Half-Duplex mode. Unfortunately,
the driver currently sets these bits unconditionally.
This patch adds the proper handling of the PAUSE frame capability
register bits by implementing the ethtool -A interface. When pause
autoneg is enabled, the controller uses the phy's capability to
negotiate PAUSE frame settings with the link partner and reconfigures
its Rx_Flow and Tx_Flow settings to match the capabilities of the
link partner. If pause autoneg is off, the PAUSE frame generation
may be forced manually (ethtool -A). Flow control is disabled by
default now.
This implementation is inspired by the tg3 driver.
Signed-off-by: Lutz Jaenicke <ljaenicke@innominate.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
23402bdd Mon Aug 12 05:53:26 CDT 2013 Claudiu Manoil <claudiu.manoil@freescale.com> gianfar: Add flow control support
eTSEC has Rx and Tx flow control capabilities that may be enabled
through MACCFG1[Rx_Flow, Tx_Flow] bits. These bits must not be set
however when eTSEC is operated in Half-Duplex mode. Unfortunately,
the driver currently sets these bits unconditionally.
This patch adds the proper handling of the PAUSE frame capability
register bits by implementing the ethtool -A interface. When pause
autoneg is enabled, the controller uses the phy's capability to
negotiate PAUSE frame settings with the link partner and reconfigures
its Rx_Flow and Tx_Flow settings to match the capabilities of the
link partner. If pause autoneg is off, the PAUSE frame generation
may be forced manually (ethtool -A). Flow control is disabled by
default now.
This implementation is inspired by the tg3 driver.
Signed-off-by: Lutz Jaenicke <ljaenicke@innominate.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|