Searched hist:"0 aacec49" (Results 1 – 2 of 2) sorted by relevance
| /openbmc/linux/drivers/net/ethernet/intel/ice/ |
| H A D | ice_ptp_hw.h | 0aacec49 Wed Aug 23 10:18:14 CDT 2023 Jacob Keller <jacob.e.keller@intel.com> ice: avoid executing commands on other ports when driving sync
The ice hardware has a synchronization mechanism used to drive the
simultaneous application of commands on both PHY ports and the source timer
in the MAC.
When issuing a sync via ice_ptp_exec_tmr_cmd(), the hardware will
simultaneously apply the commands programmed for the main timer and each
PHY port. Neither the main timer command register, nor the PHY port command
registers auto clear on command execution.
During the execution of a timer command intended for a single port on E822
devices, such as those used to configure a PHY during link up, the driver
is not correctly clearing the previous commands.
This results in unintentionally executing the last programmed command on
the main timer and other PHY ports whenever performing reconfiguration on
E822 ports after link up. This results in unintended side effects on other
timers, depending on what command was previously programmed.
To fix this, the driver must ensure that the main timer and all other PHY
ports are properly initialized to perform no action.
The enumeration for timer commands does not include an enumeration value
for doing nothing. Introduce ICE_PTP_NOP for this purpose. When writing a
timer command to hardware, leave the command bits set to zero which
indicates that no operation should be performed on that port.
Modify ice_ptp_one_port_cmd() to always initialize all ports. For all ports
other than the one being configured, write their timer command register to
ICE_PTP_NOP. This ensures that no side effect happens on the timer command.
To fix this for the PHY ports, modify ice_ptp_one_port_cmd() to always
initialize all other ports to ICE_PTP_NOP. This ensures that no side
effects happen on the other ports.
Call ice_ptp_src_cmd() with a command value if ICE_PTP_NOP in
ice_sync_phy_timer_e822() and ice_start_phy_timer_e822().
With both of these changes, the driver should no longer execute a stale
command on the main timer or another PHY port when reconfiguring one of the
PHY ports after link up.
Fixes: 3a7496234d17 ("ice: implement basic E822 PTP support")
Signed-off-by: Siddaraju DH <siddaraju.dh@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| H A D | ice_ptp_hw.c | 0aacec49 Wed Aug 23 10:18:14 CDT 2023 Jacob Keller <jacob.e.keller@intel.com> ice: avoid executing commands on other ports when driving sync
The ice hardware has a synchronization mechanism used to drive the
simultaneous application of commands on both PHY ports and the source timer
in the MAC.
When issuing a sync via ice_ptp_exec_tmr_cmd(), the hardware will
simultaneously apply the commands programmed for the main timer and each
PHY port. Neither the main timer command register, nor the PHY port command
registers auto clear on command execution.
During the execution of a timer command intended for a single port on E822
devices, such as those used to configure a PHY during link up, the driver
is not correctly clearing the previous commands.
This results in unintentionally executing the last programmed command on
the main timer and other PHY ports whenever performing reconfiguration on
E822 ports after link up. This results in unintended side effects on other
timers, depending on what command was previously programmed.
To fix this, the driver must ensure that the main timer and all other PHY
ports are properly initialized to perform no action.
The enumeration for timer commands does not include an enumeration value
for doing nothing. Introduce ICE_PTP_NOP for this purpose. When writing a
timer command to hardware, leave the command bits set to zero which
indicates that no operation should be performed on that port.
Modify ice_ptp_one_port_cmd() to always initialize all ports. For all ports
other than the one being configured, write their timer command register to
ICE_PTP_NOP. This ensures that no side effect happens on the timer command.
To fix this for the PHY ports, modify ice_ptp_one_port_cmd() to always
initialize all other ports to ICE_PTP_NOP. This ensures that no side
effects happen on the other ports.
Call ice_ptp_src_cmd() with a command value if ICE_PTP_NOP in
ice_sync_phy_timer_e822() and ice_start_phy_timer_e822().
With both of these changes, the driver should no longer execute a stale
command on the main timer or another PHY port when reconfiguring one of the
PHY ports after link up.
Fixes: 3a7496234d17 ("ice: implement basic E822 PTP support")
Signed-off-by: Siddaraju DH <siddaraju.dh@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|