Home
last modified time | relevance | path

Searched +full:vdd_l8_l9_l10_l11_l12_l13_l14 +full:- +full:supply (Results 1 – 6 of 6) sorted by relevance

/openbmc/linux/Documentation/devicetree/bindings/regulator/
H A Dqcom,spmi-regulator.yaml1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/regulator/qcom,spmi-regulator.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Robert Marko <robimarko@gmail.com>
15 - qcom,pm6125-regulators
16 - qcom,pm660-regulators
17 - qcom,pm660l-regulators
18 - qcom,pm8004-regulators
19 - qcom,pm8005-regulators
[all …]
/openbmc/linux/arch/arm64/boot/dts/qcom/
H A Dsda660-inforce-ifc6560.dts1 // SPDX-License-Identifier: BSD-3-Clause
9 /dts-v1/;
18 chassis-type = "embedded"; /* SBC */
26 stdout-path = "serial0:115200n8";
29 gpio-keys {
30 compatible = "gpio-keys";
32 key-volup {
36 debounce-interval = <15>;
41 * Until we hook up type-c detection, we
44 extcon_usb: extcon-usb {
[all …]
H A Dsdm660-xiaomi-lavender.dts1 // SPDX-License-Identifier: GPL-2.0-only
7 /dts-v1/;
12 #include <dt-bindings/input/input.h>
13 #include <dt-bindings/input/gpio-keys.h>
18 chassis-type = "handset";
25 #address-cells = <2>;
26 #size-cells = <2>;
29 stdout-path = "serial0:115200n8";
32 compatible = "simple-framebuffer";
41 vph_pwr: vph-pwr-regulator {
[all …]
H A Dsdm630-sony-xperia-nile.dtsi1 // SPDX-License-Identifier: BSD-3-Clause
10 #include <dt-bindings/gpio/gpio.h>
11 #include <dt-bindings/input/input.h>
12 #include <dt-bindings/input/gpio-keys.h>
13 #include <dt-bindings/leds/common.h>
17 qcom,msm-id = <318 0>;
18 qcom,board-id = <8 1>;
19 qcom,pmic-id = <0x1001b 0x101011a 0x00 0x00 0x1001b 0x201011a 0x00 0x00>;
21 /* This part enables graphical output via bootloader-enabled display */
25 #address-cells = <2>;
[all …]
/openbmc/linux/drivers/regulator/
H A Dqcom_smd-regulator.c1 // SPDX-License-Identifier: GPL-2.0-only
4 * Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
12 #include <linux/soc/qcom/smd-rpm.h>
49 if (vreg->enabled_updated) { in rpm_reg_write_active()
52 req[reqlen].value = cpu_to_le32(vreg->is_enabled); in rpm_reg_write_active()
56 if (vreg->uv_updated && vreg->is_enabled) { in rpm_reg_write_active()
59 req[reqlen].value = cpu_to_le32(vreg->uV); in rpm_reg_write_active()
63 if (vreg->load_updated && vreg->is_enabled) { in rpm_reg_write_active()
66 req[reqlen].value = cpu_to_le32(vreg->load / 1000); in rpm_reg_write_active()
73 ret = qcom_rpm_smd_write(vreg->rpm, QCOM_SMD_RPM_ACTIVE_STATE, in rpm_reg_write_active()
[all …]
H A Dqcom_spmi-regulator.c1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (c) 2012-2015, The Linux Foundation. All rights reserved.
8 #include <linux/devm-helpers.h>
57 * struct spmi_regulator_init_data - spmi-regulator initialization data
365 * struct spmi_voltage_range - regulator set point voltage mapping description
380 * (max_uV - min_uV) % step_uV == 0
381 * (set_point_min_uV - min_uV) % step_uV == 0*
382 * (set_point_max_uV - min_uV) % step_uV == 0*
383 * n_voltages = (set_point_max_uV - set_point_min_uV) / step_uV + 1
440 const char *supply; member
[all …]