Home
last modified time | relevance | path

Searched +full:vdd_l1_l2 +full:- +full:supply (Results 1 – 4 of 4) sorted by relevance

/openbmc/linux/Documentation/devicetree/bindings/regulator/
H A Dqcom,spmi-regulator.yaml1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/regulator/qcom,spmi-regulator.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Robert Marko <robimarko@gmail.com>
15 - qcom,pm6125-regulators
16 - qcom,pm660-regulators
17 - qcom,pm660l-regulators
18 - qcom,pm8004-regulators
19 - qcom,pm8005-regulators
[all …]
/openbmc/linux/arch/arm64/boot/dts/qcom/
H A Dqcs404-evb.dtsi1 // SPDX-License-Identifier: GPL-2.0
6 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
19 stdout-path = "serial0";
22 vph_pwr: vph-pwr-regulator {
23 compatible = "regulator-fixed";
24 regulator-name = "vph_pwr";
25 regulator-always-on;
26 regulator-boot-on;
[all …]
/openbmc/linux/drivers/regulator/
H A Dqcom_smd-regulator.c1 // SPDX-License-Identifier: GPL-2.0-only
4 * Copyright (c) 2012-2013, The Linux Foundation. All rights reserved.
12 #include <linux/soc/qcom/smd-rpm.h>
49 if (vreg->enabled_updated) { in rpm_reg_write_active()
52 req[reqlen].value = cpu_to_le32(vreg->is_enabled); in rpm_reg_write_active()
56 if (vreg->uv_updated && vreg->is_enabled) { in rpm_reg_write_active()
59 req[reqlen].value = cpu_to_le32(vreg->uV); in rpm_reg_write_active()
63 if (vreg->load_updated && vreg->is_enabled) { in rpm_reg_write_active()
66 req[reqlen].value = cpu_to_le32(vreg->load / 1000); in rpm_reg_write_active()
73 ret = qcom_rpm_smd_write(vreg->rpm, QCOM_SMD_RPM_ACTIVE_STATE, in rpm_reg_write_active()
[all …]
H A Dqcom_spmi-regulator.c1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (c) 2012-2015, The Linux Foundation. All rights reserved.
8 #include <linux/devm-helpers.h>
57 * struct spmi_regulator_init_data - spmi-regulator initialization data
365 * struct spmi_voltage_range - regulator set point voltage mapping description
380 * (max_uV - min_uV) % step_uV == 0
381 * (set_point_min_uV - min_uV) % step_uV == 0*
382 * (set_point_max_uV - min_uV) % step_uV == 0*
383 * n_voltages = (set_point_max_uV - set_point_min_uV) / step_uV + 1
440 const char *supply; member
[all …]