| /openbmc/linux/fs/xfs/ |
| H A D | xfs_pwork.h | 37 /* Have we been told to abort? */
45 /* Have we been told to abort? */
|
| /openbmc/linux/drivers/usb/serial/ |
| H A D | wishbone-serial.c | 25 * Etherbone must be told that a new stream has begun before data arrives.
27 * Similarly, when the stream ends, Etherbone must be told so that the cycle
|
| /openbmc/qemu/docs/ |
| H A D | memory-hotplug.txt | 12 In order to be able to hotplug memory, QEMU has to be told how many
80 In order to be able to hot unplug pc-dimm device, QEMU has to be told the ids
|
| /openbmc/linux/sound/hda/ |
| H A D | Kconfig | 61 to using the old SST driver, unless told otherwise through the
|
| /openbmc/linux/Documentation/admin-guide/nfs/ |
| H A D | nfsd-admin-interfaces.rst | 14 Before doing that, NFSD can be told which sockets to listen on by
|
| /openbmc/phosphor-logging/extensions/openpower-pels/ |
| H A D | host_notifier.cpp | 38 // Subscribe to be told about new PELs. in HostNotifier()
43 // Subscribe to be told about deleted PELs. in HostNotifier()
53 // Subscribe to be told about host state changes. in HostNotifier()
|
| H A D | pel_rules.cpp | 21 // Always report, unless specifically told not to in check()
|
| /openbmc/qemu/docs/system/ |
| H A D | target-i386-desc.rst.inc | 51 must be told to not have parallel ports to have working GUS.
|
| /openbmc/linux/arch/arm/mach-omap2/ |
| H A D | clockdomain.h | 111 * @wkdep_srcs: Clockdomains that can be told to wake this powerdomain up
112 * @sleepdep_srcs: Clockdomains that can be told to keep this clkdm from inact
|
| /openbmc/witherspoon-pfault-analysis/power-sequencer/ |
| H A D | pgood_monitor.hpp | 22 * power sequencer device is told to kick off a power on.
|
| /openbmc/openbmc/meta-phosphor/recipes-phosphor/initrdscripts/files/ |
| H A D | obmc-shutdown.sh | 90 # Execute the command systemd told us to ...
|
| /openbmc/linux/include/scsi/ |
| H A D | scsi_status.h | 50 DID_ABORT = 0x05, /* Told to abort for some other reason */
|
| /openbmc/linux/drivers/usb/storage/ |
| H A D | unusual_datafab.h | 21 * I'm told they exist but so far nobody has come forward to say that
|
| /openbmc/phosphor-power/power-sequencer/ |
| H A D | pgood_monitor.hpp | 22 * power sequencer device is told to kick off a power on.
|
| /openbmc/linux/drivers/parport/ |
| H A D | probe.c | 199 printk(KERN_DEBUG "%s: Device ID was %zd bytes while device told it would be %d bytes\n", in parport_read_device_id()
210 …printk(KERN_DEBUG "%s: Device ID reading stopped before device told data not available. Current id… in parport_read_device_id()
|
| /openbmc/openbmc/meta-phosphor/recipes-phosphor/power/ |
| H A D | phosphor-power_git.bb | 47 # should only build when told to.
|
| /openbmc/u-boot/doc/ |
| H A D | README.qemu-arm | 48 told to use a 64-bit CPU or it will boot in 32-bit mode.
|
| /openbmc/linux/Documentation/input/devices/ |
| H A D | bcm5974.rst | 44 with the HID driver, which, if not told otherwise, will find the standard
|
| /openbmc/u-boot/arch/arm/cpu/pxa/ |
| H A D | cpuinfo.c | 75 /* PXA26x is a sick special case as it can't be told apart from PXA25x :-( */ in pxa25x_get_revision()
|
| /openbmc/qemu/hw/net/ |
| H A D | e1000x_common.h | 73 * told us to strip it off the packet. */ in e1000x_fcs_len()
|
| /openbmc/qemu/docs/tools/ |
| H A D | qemu-trace-stap.rst | 82 unless told to only monitor a specific process.
|
| /openbmc/phosphor-pid-control/ |
| H A D | ipmi.md | 25 automatic or manual. When manual, the daemon will effectively wait to be told to
|
| /openbmc/linux/Documentation/fb/ |
| H A D | sh7760fb.rst | 48 The LCDC must explicitly be told about the type of LCD panel
|
| /openbmc/linux/arch/sparc/include/asm/ |
| H A D | switch_to_32.h | 51 * holding certain values, gcc is told that they are clobbered.
|
| /openbmc/linux/Documentation/block/ |
| H A D | writeback_cache_control.rst | 80 to be told to pass through the REQ_FUA bit using::
|