| /openbmc/openbmc-test-automation/redfish/systems/ |
| H A D | test_thermal_ambient_temperatures.robot | 26 Temperatures ReadingCelsius
39 Get Thermal Records and Verify Temperatures ReadingCelsius
45 [Documentation] Get the thermal records for temperatures.
49 # record_type The thermal record type (e.g. "Temperatures")
|
| /openbmc/linux/Documentation/hwmon/ |
| H A D | tmp103.rst | 23 temperatures to a resolution of 1°C. The TMP103 is specified for
29 The driver provides the common sysfs-interface for temperatures (see
30 Documentation/hwmon/sysfs-interface.rst under Temperatures).
|
| H A D | smsc47m192.rst | 42 Voltages and temperatures are measured by an 8-bit ADC, the resolution
43 of the temperatures is 1 bit per degree C.
49 show voltages in mV and temperatures in units of 0.001 degC.
90 temp[1-3]_max lower and upper alarm thresholds for temperatures
100 All temperatures and offsets are read and written in
|
| H A D | tmp108.rst | 22 can be set when temperatures exceed minimum or maximum values plus or minus a
40 The driver provides the common sysfs-interface for temperatures (see
41 Documentation/hwmon/sysfs-interface.rst under Temperatures).
|
| H A D | lm85.rst | 94 temperatures and five (5) voltages. It has four (4) 16-bit counters for
104 The temperatures measured are one internal diode, and two remote diodes.
114 response to the measured temperatures without further host intervention.
139 optional filter for smoothing temperatures. The ADM1027 has the same
143 measure temperatures with 0.25 degC resolution. They also provide an offset
164 The SMSC EMC6D100 & EMC6D101 monitor external voltages, temperatures, and
210 * Temperatures and Zones
278 the temperatures to compensate for systemic errors in the
|
| H A D | lm83.rst | 36 Using the adm1021 driver for a LM83 should work, but only two temperatures
71 won't have to handle more than two temperatures. Thus, ADM1021 clones
72 are sufficient, and there is no need for a four temperatures sensor
86 is given within a range of 0 to +85 degrees. Remote temperatures are
|
| H A D | adt7462.rst | 22 can also measure 13 voltages or 4 temperatures, or various combinations of the
31 response to the measured temperatures without further host intervention. This
45 The ADT7462 have a 10-bit ADC and can therefore measure temperatures
|
| H A D | k8temp.rst | 30 will auto-detect the sensors and will display only temperatures from
42 Temperatures are measured in degrees Celsius and measurement resolution is
44 temperature is updated once a second. Valid temperatures are from -49 to
|
| H A D | adt7470.rst | 24 external temperatures. It has four (4) 16-bit counters for measuring fan speed.
31 response to the measured temperatures with further host intervention. This
47 The ADT7470 has a 8-bit ADC and is capable of measuring temperatures with 1
|
| H A D | tmp513.rst | 31 temperatures, on-chip temperatures, and system voltage/power/current
34 The temperatures are measured in degrees Celsius with a range of
|
| H A D | nct6775.rst | 105 temperatures. The driver reports up to 10 of the temperatures to the user.
113 Temperatures are measured in degrees Celsius and measurement resolution is
252 points should be set to higher temperatures and higher pwm values to achieve
283 temperatures, and in some cases the reported temperature declines if the actual
|
| H A D | tmp102.rst | 30 The driver provides the common sysfs-interface for temperatures (see
31 Documentation/hwmon/sysfs-interface.rst under Temperatures).
|
| H A D | pc87360.rst | 51 (PC87366) temperatures.
117 step by step and keep an eye on temperatures.
126 Temperatures are reported in degrees Celsius. Each temperature measured has
137 measurement) one. As a consequence, these temperatures are exported as
138 voltages, and converted into temperatures in user-space.
|
| H A D | wm831x.rst | 34 Temperatures are sampled by a 12 bit ADC. Chip and battery temperatures
|
| H A D | da9055.rst | 50 Temperatures are sampled by a 10 bit ADC. Junction temperatures
|
| H A D | tmp401.rst | 64 The driver provides the common sysfs-interface for temperatures (see
65 Documentation/hwmon/sysfs-interface.rst under Temperatures).
|
| H A D | adt7475.rst | 58 temperatures and two (2) or more voltages. It has four (4) 16-bit counters
66 response to the measured temperatures without further host intervention.
115 The ADT747x has a 10-bit ADC and can therefore measure temperatures
|
| H A D | thmc50.rst | 51 until the temperature falls below the Hysteresis value. All temperatures are in
71 The driver provides up to three temperatures:
|
| /openbmc/linux/Documentation/devicetree/bindings/hwmon/ |
| H A D | max6697.txt | 32 Select bit 0 for local temperature, bit 1..7 for remote temperatures.
37 Select bit 0 for local temperature, bit 1..7 for remote temperatures.
45 Only supported for remote temperatures (bit 1..7).
|
| H A D | ti,tmp513.yaml | 17 remote temperatures, on-chip temperatures, and system voltage/power/current
|
| /openbmc/bmcweb/redfish-core/lib/ |
| H A D | thermal.hpp | 77 "Temperatures", temperatureCollections // in requestRoutesThermal()
86 "Temperatures / Voltages"); in requestRoutesThermal()
91 allCollections.emplace("Temperatures", in requestRoutesThermal()
|
| /openbmc/linux/Documentation/devicetree/bindings/thermal/ |
| H A D | nvidia,tegra186-bpmp-thermal.yaml | 15 an interface that is used to read system temperatures, including CPU
16 cluster and GPU temperatures. This binding describes the thermal
|
| H A D | ti,j72xx-thermal.yaml | 15 sensors to measure silicon junction temperatures from different
39 temperatures accurately.
|
| /openbmc/openpower-occ-control/ |
| H A D | README.md | 4 processors. The OCC provides processor and memory temperatures, power readings,
6 Control will be interfacing with the OCC to collect the temperatures and power
|
| /openbmc/linux/Documentation/devicetree/bindings/iio/adc/ |
| H A D | mediatek,mt2701-auxadc.yaml | 15 in some Mediatek SoCs which among other things measures the temperatures
17 used by thermal controller which reads the temperatures from the AUXADC
|