| /openbmc/linux/drivers/usb/phy/ |
| H A D | phy-fsl-usb.c | 116 /* Charge vbus for vbus pulsing in SRP */
169 * data-line pulsing in SRP
204 /* Start SRP pulsing by data-line pulsing, followed with v-bus pulsing. */
247 * residual voltage of vbus pulsing and A device pull up in b_vbus_pulse_end()
|
| H A D | phy-fsl-usb.h | 271 #define TB_VBUS_PLS (30) /* time to keep vbus pulsing asserted */
|
| /openbmc/linux/Documentation/devicetree/bindings/leds/ |
| H A D | ti,tca6507.yaml | 14 7 separate lines either by holding them low, or by pulsing them with modulated
|
| /openbmc/linux/arch/arm/mach-lpc32xx/ |
| H A D | serial.c | 139 /* Disable IrDA pulsing support on UART6 */ in lpc32xx_serial_init()
|
| /openbmc/linux/drivers/usb/chipidea/ |
| H A D | otg_fsm.c | 539 * Start SRP pulsing by data-line pulsing,
540 * no v-bus pulsing followed
|
| /openbmc/linux/drivers/iio/dac/ |
| H A D | ti-dac7612.c | 141 * event can change the value of all DACs by pulsing down the LOADDACs in dac7612_probe()
|
| /openbmc/linux/drivers/leds/ |
| H A D | leds-spi-byte.c | 20 * * Mode: 01 -> pulsing pattern (min -> max -> min) with an interval. From
|
| H A D | leds-tca6507.c | 6 * separate lines either by holding them low, or by pulsing them
|
| /openbmc/linux/drivers/input/misc/ |
| H A D | powermate.c | 24 * intensity, or to a rhythmic pulsing. Several patterns and speeds are available.
261 …bits 8-16: 9 bits: pulsing speed modifier (0 ... 510); 0-254 = slower, 255 = standard, 256-510 = … in powermate_input_event()
|
| /openbmc/linux/include/linux/usb/ |
| H A D | otg-fsm.h | 109 * @data_pulse: TRUE when the B-device is performing data line pulsing
|
| /openbmc/linux/arch/arm/boot/dts/amlogic/ |
| H A D | meson8b-ec100.dts | 83 * "breathing"/pulsing effect until the power is fully
|
| /openbmc/linux/drivers/net/phy/ |
| H A D | intel-xway.c | 126 /* Pulsing Configuration */
|
| /openbmc/linux/drivers/net/ethernet/aquantia/atlantic/ |
| H A D | aq_ptp.c | 371 "Enable GPIO %d pulsing, start time %llu, period %u\n", in aq_ptp_hw_pin_conf()
375 "Disable GPIO %d pulsing, start time %llu, period %u\n", in aq_ptp_hw_pin_conf()
|
| /openbmc/u-boot/test/py/ |
| H A D | README.md | 248 to flash, pulsing the board's reset signal is likely all this script need do.
|
| /openbmc/qemu/hw/nvme/ |
| H A D | trace-events | 3 pci_nvme_irq_pin(void) "pulsing IRQ pin"
|
| /openbmc/linux/Documentation/driver-api/ |
| H A D | generic-counter.rst | 156 In this example, the Signal is a source input line with a pulsing
|
| /openbmc/u-boot/drivers/usb/host/ |
| H A D | dwc2.h | 785 #undef CONFIG_DWC2_TS_DLINE /* External DLine pulsing */
|
| H A D | dwc2.c | 345 /* Set external TS Dline pulsing */ in dwc_otg_core_init()
|
| /openbmc/linux/drivers/pmdomain/imx/ |
| H A D | imx8mp-blk-ctrl.c | 430 * power domain is powered down. To ensure the proper reset pulsing, in imx8mp_hdmi_power_notifier()
|
| /openbmc/qemu/hw/input/ |
| H A D | pckbd.c | 326 * The only useful version of this command is pulsing bit 0, in kbd_write_command()
|
| /openbmc/linux/drivers/comedi/drivers/ |
| H A D | s626.c | 1389 /* Start ADC by pulsing GPIO1. */ in s626_reset_adc()
1516 /* Start ADC by pulsing GPIO1 low */ in s626_ai_insn_read()
|
| /openbmc/linux/drivers/usb/dwc2/ |
| H A D | core.h | 332 * @ts_dline: Enable Term Select Dline pulsing
|
| /openbmc/qemu/hw/intc/ |
| H A D | armv7m_nvic.c | 957 * Pulsing the IRQ will always run the handler in set_irq_level()
|
| /openbmc/linux/drivers/gpu/drm/bridge/synopsys/ |
| H A D | dw-hdmi.c | 298 * other than pulsing the SDA line. in dw_hdmi_i2c_unwedge()
|
| /openbmc/linux/drivers/media/pci/bt8xx/ |
| H A D | bttv-cards.c | 4369 * connection prior to establish a new one, pulsing the STROBE pin.
|