| /openbmc/linux/drivers/pcmcia/ |
| H A D | bcm63xx_pcmcia.c | 128 /* VS1 grounded, VS2 float */
131 /* VS1 grounded, VS2 grounded */
137 /* VS1 grounded, VS2 tied to CD2 */
140 /* VS1 tied to CD2, VS2 grounded */
143 /* VS1 float, VS2 grounded */
155 /* VS2 grounded, VS1 is tied to CD1, CD2 is grounded */
|
| /openbmc/linux/Documentation/ABI/testing/ |
| H A D | sysfs-bus-iio-sx9324 | 10 + grounded (GD),
|
| /openbmc/linux/drivers/net/wireless/microchip/wilc1000/ |
| H A D | Kconfig | 22 To use this interface, pin9 (SDIO_SPI_CFG) must be grounded. Select
|
| /openbmc/linux/drivers/iio/accel/ |
| H A D | adxl345_i2c.c | 8 * 0x53 (ALT ADDRESS pin grounded)
|
| /openbmc/linux/Documentation/devicetree/bindings/mfd/ |
| H A D | rohm,bd9576-pmic.yaml | 50 the ddr-sel pin low or high. Set this property if ddr-sel is grounded.
|
| /openbmc/linux/Documentation/spi/ |
| H A D | spi-lm70llp.rst | 69 and not grounded by the host via D7), the transistor conducts and switches
|
| /openbmc/linux/arch/arm/boot/dts/ti/omap/ |
| H A D | dra62x-j5eco-evm.dts | 131 /* USB0_ID pin state: SW10[1] = 0 cable detection, SW10[1] = 1 ID grounded */
|
| /openbmc/linux/arch/arm64/boot/dts/ti/ |
| H A D | k3-j721s2-som-p0.dtsi | 47 /* standby pin has been grounded by default */
|
| /openbmc/linux/drivers/gpu/drm/amd/display/dc/gpio/ |
| H A D | hw_gpio.c | 111 * So (A) is grounded, output is driven by (EN = 0) in dal_hw_gpio_set_value()
|
| /openbmc/linux/Documentation/devicetree/bindings/iio/proximity/ |
| H A D | semtech,sx9324.yaml | 50 3 : grounded.
|
| /openbmc/linux/include/linux/usb/ |
| H A D | phy.h | 30 USB_EVENT_ID, /* id was grounded */
|
| /openbmc/linux/drivers/phy/ti/ |
| H A D | phy-omap-control.c | 138 * omap_control_usb_host_mode - set AVALID, VBUSVALID and ID pin in grounded
|
| /openbmc/linux/arch/arm/boot/dts/st/ |
| H A D | ste-hrefv60plus.dtsi | 253 * (presumably pins are unconnected therefore grounded here,
|
| /openbmc/u-boot/arch/arm/dts/ |
| H A D | tegra30-cardhu.dts | 33 /* AVDD_PEXA and VDD_PEXA inputs are grounded on Cardhu. */
|
| /openbmc/u-boot/board/inversepath/usbarmory/ |
| H A D | usbarmory.c | 125 /* Grounded pads */ in setup_iomux_unused_boot()
|
| /openbmc/linux/drivers/pwm/ |
| H A D | pwm-meson.c | 352 * The last 2 are grounded
|
| /openbmc/linux/drivers/usb/musb/ |
| H A D | tusb6010.c | 408 /* REVISIT writeup of WID implies that if WID set and ID is grounded, in tusb_allow_idle()
585 /* If ID pin is grounded, we want to be a_idle */ in tusb_musb_set_vbus()
|
| H A D | da8xx.c | 175 * grounded and we're now in the A-Default state machine. in otg_timer()
|
| /openbmc/linux/arch/arm/boot/dts/nvidia/ |
| H A D | tegra30-cardhu.dtsi | 53 /* AVDD_PEXA and VDD_PEXA inputs are grounded on Cardhu. */
|
| /openbmc/u-boot/drivers/usb/musb-new/ |
| H A D | musb_core.c | 616 * this silicon doesn't report ID-no-longer-grounded. in musb_stage0_irq()
932 * (a) ID-grounded irq, host mode; in musb_start()
2052 * (We expect the ID pin to be forcibly grounded!!) in musb_init_controller()
|
| /openbmc/linux/drivers/auxdisplay/ |
| H A D | panel.c | 1134 /* 1 for each grounded input */ in phys_scan_contacts()
1137 /* grounded inputs are signals 40-44 */ in phys_scan_contacts()
|
| /openbmc/qemu/hw/misc/ |
| H A D | npcm7xx_clk.c | 127 /* The PLL is grounded if it is not locked yet. */ in npcm7xx_clk_update_pll()
|
| /openbmc/linux/drivers/comedi/drivers/ |
| H A D | jr3_pci.h | 576 * without a hardware problem. If the sensor is well grounded, this
|
| /openbmc/linux/drivers/iio/proximity/ |
| H A D | sx9324.c | 805 /* TODO(gwendal): PHx use chip default or all grounded? */
|
| /openbmc/qemu/include/hw/ |
| H A D | qdev-core.h | 598 * is active when the voltage on the pin is low (or grounded).
|