| /openbmc/linux/fs/gfs2/ |
| H A D | aops.c | 318 int cycled; in gfs2_write_cache_jdata() local
327 cycled = 1; in gfs2_write_cache_jdata()
329 cycled = 0; in gfs2_write_cache_jdata()
336 cycled = 1; /* ignore range_cyclic tests */ in gfs2_write_cache_jdata()
363 if (!cycled && !done) { in gfs2_write_cache_jdata()
369 cycled = 1; in gfs2_write_cache_jdata()
|
| /openbmc/phosphor-dbus-interfaces/yaml/xyz/openbmc_project/State/ |
| H A D | Chassis.interface.yaml | 50 Chassis power should be cycled from off to on. There will be a 5
|
| H A D | Host.interface.yaml | 53 Host firmware should be rebooted. Chassis power will be cycled
|
| /openbmc/linux/drivers/media/usb/gspca/m5602/ |
| H A D | m5602_core.c | 205 unfortunately this breaks the camera until it's power cycled */
214 pr_info("Warning: The ALi m5602 webcam probably won't work until it's power cycled\n"); in m5602_dump_bridge()
|
| /openbmc/linux/Documentation/userspace-api/media/v4l/ |
| H A D | userp.rst | 52 cycled, applications can pass different addresses and sizes at each
|
| H A D | dmabuf.rst | 64 descriptor. Although buffers are commonly cycled, applications can pass
|
| /openbmc/linux/arch/arm64/boot/dts/qcom/ |
| H A D | sc7180-trogdor-homestar.dtsi | 95 * The atna33xc20 really likes to be power cycled to keep it from
|
| /openbmc/linux/Documentation/w1/slaves/ |
| H A D | w1_therm.rst | 72 the sensor. Resolution is reset when the sensor gets power-cycled.
|
| /openbmc/openbmc/poky/meta/lib/oeqa/controllers/ |
| H A D | controllerimage.py | 116 ''' Waits until the target device has booted (if we have just power cycled it) '''
|
| /openbmc/linux/drivers/gpu/drm/panel/ |
| H A D | panel-samsung-atna33xc20.c | 156 * cycled yet. This lets us know that "el_on3_off_time" is recent (we in atana33xc20_disable()
|
| /openbmc/linux/drivers/iio/adc/ |
| H A D | ti-ads1100.c | 404 * has been power-cycled, we'll re-write its config register now. in ads1100_runtime_resume()
|
| /openbmc/linux/drivers/net/wireless/ti/wlcore/ |
| H A D | sdio.c | 145 * To guarantee that the SDIO card is power cycled, as required to make in wl12xx_sdio_power_on()
|
| /openbmc/linux/drivers/leds/flash/ |
| H A D | leds-aat1290.c | 190 * To reenter movie mode after a flash event the part must be cycled in aat1290_led_flash_strobe_set()
|
| /openbmc/qemu/docs/system/devices/ |
| H A D | nvme.rst | 26 is power cycled.
|
| /openbmc/linux/Documentation/networking/device_drivers/ethernet/intel/ |
| H A D | e1000e.rst | 240 NOTE: The machine must be power cycled (full off/on) when enabling NVM writes
|
| /openbmc/linux/tools/testing/selftests/pidfd/ |
| H A D | pidfd_test.c | 146 * If users set a higher limit or we have cycled PIDFD_MAX_DEFAULT number of
|
| /openbmc/linux/Documentation/ABI/testing/ |
| H A D | sysfs-bus-thunderbolt | 229 based mailbox before the device is power cycled. Writing
|
| /openbmc/linux/drivers/hwmon/ |
| H A D | drivetemp.c | 294 * freeze until power-cycled under heavy write loads when their temperature is
|
| /openbmc/linux/sound/soc/codecs/ |
| H A D | tda7419.c | 599 * been previously initialized and not power cycled before probe. in tda7419_probe()
|
| /openbmc/linux/drivers/usb/host/ |
| H A D | ehci-fsl.c | 386 * Deal with MPC834X/85XX that need port power to be cycled in ehci_fsl_setup()
|
| /openbmc/linux/drivers/gpu/drm/bridge/ |
| H A D | parade-ps8640.c | 485 * The bridge seems to expect everything to be power cycled at the in ps8640_atomic_post_disable()
|
| /openbmc/linux/drivers/mtd/chips/ |
| H A D | cfi_cmdset_0020.c | 1359 get power cycled */ in cfi_staa_suspend()
1383 /* Go to known state. Chip may have been power cycled */ in cfi_staa_resume()
|
| /openbmc/linux/drivers/net/ethernet/stmicro/stmmac/ |
| H A D | dwmac-qcom-ethqos.c | 714 * cycled. The actual configuration will be adjusted once in ethqos_clks_config()
|
| /openbmc/linux/drivers/scsi/lpfc/ |
| H A D | lpfc_ct.c | 1111 * The driver has cycled through all Nports in the RSCN payload. in lpfc_cmpl_ct_cmd_gid_ft()
1331 * The driver has cycled through all Nports in the RSCN payload. in lpfc_cmpl_ct_cmd_gid_pt()
1478 * The driver has cycled through all Nports in the RSCN payload. in lpfc_cmpl_ct_cmd_gff_id()
|
| /openbmc/linux/sound/usb/ |
| H A D | mixer_scarlett.c | 43 * - automatic re-initialization on connect if device was power-cycled
|