Home
last modified time | relevance | path

Searched full:currents (Results 1 – 25 of 60) sorted by relevance

123

/openbmc/linux/include/linux/
H A Dentry-common.h67 * @regs: Pointer to currents pt_regs
105 * @regs: Pointer to currents pt_regs
123 * @regs: Pointer to currents pt_regs
148 * @regs: Pointer to currents pt_regs
198 * @regs: Pointer to currents pt_regs
218 * @regs: Pointer to currents pt_regs
255 * @regs: Pointer to currents pt_regs
283 * @regs: Pointer to currents pt_regs
298 * @regs: Pointer to currents pt_regs
329 * @regs: Pointer to currents pt_regs
[all …]
/openbmc/linux/Documentation/sphinx/templates/
H A Dkernel-toc.html14 let currents = document.getElementsByClassName("current")
15 sbar.scrollTop = currents[currents.length - 1].offsetTop;
/openbmc/linux/Documentation/devicetree/bindings/iio/adc/
H A Dadi,ad7192.yaml75 adi,burnout-currents-enable:
78 path are enabled. When BURN = 0, the burnout currents are disabled.
79 The burnout currents can be enabled only when the buffer is active
127 adi,burnout-currents-enable;
/openbmc/linux/Documentation/hwmon/
H A Dtmp513.rst56 The driver exports the shunt currents values via the following sysFs files:
84 The bus power and bus currents range and resolution depends on the calibration
H A Dmc34vr500.rst20 monitors the temperature, input voltage and output currents and provides
H A Dvexpress.rst32 providing information about power lines voltages and currents, board
H A Dadm1275.rst82 or current scaling. Reported voltages, currents, and power are raw measurements,
/openbmc/u-boot/drivers/power/
H A Daxp209.c113 * great inrush currents. To prevent this, boards can enable a certain in axp_set_aldo3()
131 * high inrush currents, the voltage slope should be increased. in axp_set_aldo3()
/openbmc/linux/Documentation/devicetree/bindings/power/supply/
H A Dx-powers,axp20x-battery-power-supply.yaml11 currents of the battery by reading ADC channels from the ADC.
/openbmc/linux/include/linux/power/
H A Dbq2415x_charger.h13 * voltages and currents which can be also later configured via sysfs. If
/openbmc/linux/Documentation/devicetree/bindings/leds/
H A Dqcom,pm8058-led.yaml19 Hardware-wise the different LEDs support slightly different output currents.
H A Dleds-lm3532.txt7 method allows for different LED currents in each current sink thus allowing
/openbmc/bmcweb/redfish-core/schema/dmtf/json-schema/
H A DBatteryMetrics.v1_0_4.json135 "description": "The output currents (A) for this battery.",
140 …"longDescription": "This property shall contain the output currents, in ampere units, for this bat…
H A DPowerSupplyMetrics.v1_1_2.json225 "description": "The output currents (A) for this power supply.",
230 …"longDescription": "This property shall contain the output currents, in ampere units, for this pow…
/openbmc/linux/Documentation/sound/soc/
H A Doverview.rst24 power via changing codec oversampling rates, bias currents, etc.
/openbmc/linux/Documentation/devicetree/bindings/regulator/
H A Dgpio-regulator.yaml56 description: Selection of available voltages/currents provided by this
/openbmc/linux/drivers/regulator/
H A Dbd71815-regulator.c475 #define BD71815_LED_REG(_name, _id, csel, mask, ereg, emsk, currents) \ argument
481 .n_current_limits = ARRAY_SIZE(currents), \
486 .curr_table = currents, \
/openbmc/linux/Documentation/leds/
H A Dleds-lm3556.rst22 from 93.75 mA to 1500 mA.The Flash currents are adjusted via the CURRENT
/openbmc/bmcweb/redfish-core/schema/dmtf/csdl/
H A DBatteryMetrics_v1.xml96 <Annotation Term="OData.Description" String="The output currents (A) for this battery."/>
97 …="OData.LongDescription" String="This property shall contain the output currents, in ampere units,…
H A DPowerSupplyMetrics_v1.xml116 … <Annotation Term="OData.Description" String="The output currents (A) for this power supply."/>
117 …="OData.LongDescription" String="This property shall contain the output currents, in ampere units,…
/openbmc/linux/drivers/hwmon/pmbus/
H A Ducd9200.c149 * READ_IOUT will return the sum of currents of all phases of a rail, in ucd9200_probe()
/openbmc/linux/drivers/hwmon/
H A Dltc4151.c140 /* Currents (via sense resistor) */
/openbmc/linux/Documentation/devicetree/bindings/mfd/
H A Drohm,bd71828-pmic.yaml57 BD71827 and BD71828 have SAR ADC for measuring charging currents.
H A Drohm,bd71815-pmic.yaml57 BD71827 and BD71828 have SAR ADC for measuring charging currents.
/openbmc/linux/Documentation/driver-api/
H A Dregulator.rst99 interface for this. Both take ranges of voltages and currents, supporting

123