| /openbmc/linux/arch/arm64/boot/dts/qcom/ |
| H A D | sc7280-herobrine-wifi-sku.dtsi | 3 * Google Herobrine dts fragment for WIFI SKUs
8 /* WIFI SKUs save 256M by not having modem/mba/rmtfs memory regions defined. */
|
| H A D | sc7280-herobrine-pro-sku.dtsi | 3 * Google Herobrine dts fragment for PRO SKUs
|
| H A D | sc7280-herobrine-nvme-sku.dtsi | 3 * Google Herobrine dts fragment for NVMe SKUs
|
| H A D | sc7180-trogdor-lte-sku.dtsi | 3 * Google Trogdor dts fragment for LTE SKUs
|
| H A D | sc7280-herobrine-lte-sku.dtsi | 3 * Google Herobrine dts fragment for LTE SKUs
|
| H A D | sc7180-trogdor.dtsi | 889 /* This gets overridden for SKUs with LTE support. */
|
| /openbmc/qemu/hw/xen/ |
| H A D | xen_pt_graphics.c | 301 * the different PCH DIDs likely map to different PCH SKUs. We do the
302 * same thing for the GPU. For PCH, the different SKUs are going to be
305 * consistent across all SKUs in a given family (eg LPT). But just same
|
| /openbmc/linux/drivers/gpu/drm/amd/amdgpu/ |
| H A D | amdgpu_fru_eeprom.c | 62 /* D161 and D163 are the VG20 server SKUs */ in is_fru_eeprom_supported()
74 /* All Aldebaran SKUs have an FRU */ in is_fru_eeprom_supported()
|
| H A D | sdma_v4_0.c | 540 * Server SKUs take a different hysteresis setting from other SKUs. in sdma_v4_0_setup_ulv()
|
| /openbmc/u-boot/arch/arm/include/asm/arch-tegra/ |
| H A D | tegra.h | 63 /* These are the available SKUs (product types) for Tegra */
|
| /openbmc/linux/arch/x86/kernel/cpu/resctrl/ |
| H A D | core.c | 121 * the MSRs won't #GP fault because only the following SKUs support
188 * There are no Intel SKUs as of now to support non-linear delay. in rdt_get_mb_table()
314 * There are currently no SKUs which support non linear delay values.
|
| H A D | ctrlmondata.c | 36 * Only linear delay values is supported for current Intel SKUs. in bw_validate()
|
| /openbmc/linux/Documentation/devicetree/bindings/display/panel/ |
| H A D | panel-edp.yaml | 17 board, either for second-sourcing purposes or to support multiple SKUs
|
| /openbmc/linux/drivers/net/wireless/realtek/rtlwifi/ |
| H A D | regd.c | 196 *on these channels. This is only done for specific regulatory SKUs in _rtl_reg_apply_active_scan_flags()
|
| /openbmc/linux/arch/arm/boot/dts/nxp/imx/ |
| H A D | imx7-colibri.dtsi | 375 /* NAND on such SKUs */
629 /* eMMC on 1GB (eMMC) SKUs */
|
| /openbmc/linux/drivers/net/wireless/ath/ |
| H A D | regd.c | 368 * regulatory SKUs.
|
| /openbmc/linux/arch/arm64/boot/dts/ti/ |
| H A D | k3-am62-verdin.dtsi | 536 /* On-module Wi-Fi on WB SKUs, module-specific SDIO otherwise */
640 /* Bluetooth on WB SKUs, module-specific UART otherwise */
|
| /openbmc/linux/drivers/gpu/drm/i915/ |
| H A D | intel_clock_gating.c | 83 * GEN8_HDCUNIT_CLOCK_GATE_DISABLE_HDCREQ applies on 3x6 GT SKUs only. in bxt_init_clock_gating()
|
| /openbmc/linux/Documentation/accel/qaic/ |
| H A D | aic100.rst | 34 uses the standard Qualcomm VID (0x17cb). All AIC100 SKUs use the same
|
| /openbmc/u-boot/drivers/video/ |
| H A D | ivybridge_igd.c | 430 * Unfortunately it does not work reliably on all SKUs so in gma_pm_init_pre_vbios()
|
| /openbmc/linux/drivers/gpu/drm/i915/display/ |
| H A D | intel_display_device.c | 611 * code making a mess on SKUs where the PHY is missing.
|
| /openbmc/linux/drivers/usb/serial/ |
| H A D | sierra.c | 93 /* Dummy interface present on some SKUs should be ignored */ in sierra_calc_num_ports()
|
| /openbmc/linux/arch/arm64/boot/dts/freescale/ |
| H A D | imx8mp-verdin.dtsi | 815 /* Verdin UART_4, used for Bluetooth on Wi-Fi/Bluetooth SKUs */
|
| /openbmc/openbmc/poky/documentation/dev-manual/ |
| H A D | start.rst | 536 Hyper-V. Not all SKUs of Windows can install Hyper-V. As an alternative,
|
| /openbmc/linux/drivers/gpu/drm/amd/display/dc/dcn32/ |
| H A D | dcn32_resource.c | 2720 * DCN32 and DCN321 SKUs may have different sizes for MALL in dcn32_calc_num_avail_chans_for_mall()
2729 * Calculating the MALL sizes for all available SKUs, we in dcn32_calc_num_avail_chans_for_mall()
|