| /openbmc/qemu/include/hw/sensor/ |
| H A D | tmp105.h | 47 * The TMP105 initially looks for a temperature rising above T_high;
49 * temperature falling below T_low. This flag is false when initially
|
| /openbmc/phosphor-power/phosphor-regulators/src/ |
| H A D | presence_service.cpp | 27 // Initially assume hardware is not present in isPresent()
67 // Initially assume exception is not one of the expected types in isExpectedException()
|
| /openbmc/linux/Documentation/ABI/testing/ |
| H A D | sysfs-bus-counter | 94 The output signal is initially low, and will remain low
100 The output signal is initially high. The output signal
109 The output signal is initially high. When the counter
116 The output signal is initially high.
135 The output signal is initially high. When the count
141 The output signal is initially high. Counting is started
|
| /openbmc/linux/include/linux/ |
| H A D | jump_label.h | 32 * define a "key" that is initially false via "DEFINE_STATIC_KEY_FALSE(key)",
35 * Similarly, we can define an initially true key via
39 * initially true or false can be using in both static_branch_unlikely()
47 * initially false key that is used in an "if (static_branch_unlikely(&key))"
96 * bit 0 => 1 if key is initially true
97 * 0 if initially false
|
| /openbmc/phosphor-power/phosphor-regulators/test/ |
| H A D | id_map_tests.cpp | 47 // Verify device is not initially in map in TEST()
95 // Verify rail is not initially in map in TEST()
137 // Verify rule is not initially in map in TEST()
|
| /openbmc/qemu/docs/system/devices/ |
| H A D | nvme.rst | 129 not attached to any controllers initially. A shared namespace with this set
141 will cause NSID 1 will be a shared namespace that is initially attached to both
144 attached to any controller initially (due to ``detached=on``) or to hotplugged
161 Buffer support (i.e, the CMB is initially disabled and must be explicitly
|
| /openbmc/phosphor-power/phosphor-power-sequencer/src/ |
| H A D | services.cpp | 62 // Initially assume hardware is not present in isPresent()
125 // Initially assume exception is not one of the expected types in isExpectedException()
|
| /openbmc/qemu/hw/s390x/ |
| H A D | tod-kvm.c | 65 * is the point where we want to stop the initially running TOD to fire in kvm_s390_tod_set()
151 * The TOD is initially running (value stored in KVM). Avoid needless in kvm_s390_tod_init()
|
| /openbmc/openbmc/meta-ibm/conf/machine/ |
| H A D | huygens.conf | 5 # Focus Huygens initially on a multi-BMC setup for integrating
|
| /openbmc/openbmc/meta-openembedded/meta-python/recipes-devtools/python/ |
| H A D | python3-et-xmlfile_2.0.0.bb | 3 to be developed that will work with both libraries. It was developed initially for \
|
| H A D | python3-openpyxl_3.1.5.bb | 4 was initially based on PHPExcel."
|
| /openbmc/phosphor-power/phosphor-regulators/docs/config_file/ |
| H A D | set_device.md | 7 Many actions read from or write to a device. Initially this is the
|
| /openbmc/linux/drivers/usb/storage/ |
| H A D | unusual_uas.h | 39 * Initially Reported-by: Julian Groß <julian.g@posteo.de>
157 * Initially Reported-by: Takeo Nakayama <javhera@gmx.com>
|
| /openbmc/linux/drivers/usb/cdns3/ |
| H A D | drd.h | 164 * 100 - Controller initially configured as Device
168 * 100 - Controller initially configured as Device.
|
| /openbmc/linux/tools/perf/Documentation/ |
| H A D | perf-test.txt | 15 This command does assorted sanity tests, initially through linked routines but
|
| /openbmc/linux/drivers/soc/loongson/ |
| H A D | Kconfig | 16 SoCs. Initially only reading SVR and registering soc device are
|
| /openbmc/linux/arch/arm/plat-orion/ |
| H A D | irq.c | 28 * Mask all interrupts initially. in orion_irq_init()
|
| /openbmc/linux/drivers/android/ |
| H A D | Kconfig | 24 Each binderfs mount initially only contains a binder-control device.
|
| /openbmc/linux/tools/testing/selftests/net/ |
| H A D | tcp_fastopen_backup_key.sh | 28 # initially present an old TFO cookie
|
| /openbmc/u-boot/doc/ |
| H A D | README.fsl-trustzone-components | 24 - Supports 8 fully programmable address regions, initially inactive at reset,
|
| /openbmc/u-boot/arch/x86/cpu/quark/ |
| H A D | mrc.c | 79 /* initially expect success */ in mrc_adjust_params()
96 /* initially no memory */ in mrc_adjust_params()
|
| /openbmc/linux/fs/jfs/ |
| H A D | jfs_extent.c | 111 /* allocate the disk blocks for the extent. initially, extBalloc() in extAlloc()
272 * initially, we will try to allocate disk blocks for the
308 /* get the number of blocks to initially attempt to allocate. in extBalloc()
|
| /openbmc/openbmc/poky/meta-poky/conf/templates/default/ |
| H A D | local.conf.sample | 8 # initially. There's also site.conf.sample which contains examples of site specific
90 # The default value is fine for general Yocto project use, at least initially.
234 # initially but it will then speed up the builds by not having to build things if they are
|
| /openbmc/linux/security/smack/ |
| H A D | Kconfig | 25 of access initially with the bringup mode set on the
|
| /openbmc/linux/Documentation/devicetree/bindings/power/reset/ |
| H A D | gpio-poweroff.yaml | 31 Initially configure the GPIO line as an input. Only reconfigure
|