| /openbmc/linux/Documentation/devicetree/bindings/regulator/ |
| H A D | rohm,bd71815-regulator.yaml | 57 comments below for bucks/LDOs which support this. 0 means
77 comments below for bucks/LDOs which support this. 0 means
86 comments below for bucks/LDOs which support this. 0 means
92 # Bucks 1 and 2 support giving separate voltages for operational states
95 # state changes. Omitting these properties from bucks 1 and 2 leave
99 # Bucks 3-5 and ldos 1-5 support setting the RUN state voltage here.
109 # that setting non zero voltages for bucks 1/2 will also enable voltage
|
| H A D | samsung,s2mpa01.yaml | 33 # 10 bucks
51 Note: Some bucks share the ramp rate setting i.e. same ramp value
52 will be set for a particular group of bucks so provide the same
|
| H A D | rohm,bd71828-regulator.yaml | 54 bucks which support this. 0 means disabled.
62 bucks which support this. 0 means disabled.
70 bucks which support this. 0 means disabled.
78 bucks which support this. 0 means disabled.
|
| H A D | maxim,max77802.yaml | 31 regulators are:: bucks 2-4 and LDOs 1-35. Also, it only takes effect if the
64 bucks supporting the regulator-mode property (changing mode to Low Power
|
| H A D | rohm,bd71847-regulator.yaml | 62 bucks which support this. 0 means disabled.
70 bucks which support this. 0 means disabled.
78 bucks which support this. 0 means disabled.
|
| H A D | rohm,bd71837-regulator.yaml | 63 bucks which support this. 0 means disabled.
71 bucks which support this. 0 means disabled.
79 bucks which support this. 0 means disabled.
|
| H A D | maxim,max8997.yaml | 104 When GPIO-DVS mode is used for multiple bucks, changing the voltage value
105 of one of the bucks may affect that of another buck, which is the side
134 # 7 bucks
|
| H A D | samsung,s2mps11.yaml | 33 # 10 bucks
|
| H A D | samsung,s2mpu02.yaml | 33 # 7 bucks
|
| H A D | samsung,s2mps15.yaml | 33 # 10 bucks
|
| H A D | samsung,s2mps13.yaml | 33 # 10 bucks
|
| H A D | samsung,s2mps14.yaml | 50 # 5 bucks
|
| H A D | mt6315-regulator.yaml | 14 that contains 4 BUCKs output which can combine with each other
|
| H A D | maxim,max77686.yaml | 54 # 9 bucks
|
| H A D | samsung,s5m8767.yaml | 46 # 8 bucks
|
| /openbmc/u-boot/drivers/power/regulator/ |
| H A D | Kconfig | 33 driver implements get/set api for the various BUCKS and LDOS supported
42 driver implements enable/disable for step-down bucks and LDOs,
60 of regulator. The driver implements get/set api for the various BUCKS.
130 driver implements get/set api for the various BUCKS and LDOs supported
148 common requirements, including all LDOs and BUCKs. This allows many
226 LP87565 series of PMICs have 4 single phase BUCKs that can also
252 driver implements get/set api for the various BUCKS and LDOs supported
|
| /openbmc/linux/Documentation/devicetree/bindings/mfd/ |
| H A D | da9062.txt | 11 da9062-regulator : : LDOs & BUCKs
22 da9062-regulator : : LDOs & BUCKs
54 - regulators : This node defines the settings for the LDOs and BUCKs.
|
| H A D | mediatek,mt6357.yaml | 44 List of MT6357 BUCKs and LDOs regulators.
|
| /openbmc/linux/drivers/regulator/ |
| H A D | max77802-regulator.c | 268 /* BUCKS 1, 6 */
282 /* BUCKs 2-4 */
297 /* BUCKs 5, 7-10 */
352 /* BUCKs 1, 6 */
377 /* BUCKS 2-4 */
424 /* BUCKs 7-10 */
|
| H A D | Kconfig | 283 Say y here to support the BUCKs and LDOs regulators found on
297 Say y here to support the BUCKs and LDOs regulators found on
307 Say y here to support the BUCKs and LDOs regulators found on
317 Say y here to support the BUCKs and LDOs regulators found on
413 21 general purpose LDOs, 3 dedicated LDOs, and 5 BUCKs. All
1285 via I2C bus. S2MPA01 has 10 Bucks and 26 LDO outputs.
1301 via I2C bus. S5M8767A have 9 Bucks and 28 LDOs output and
1537 TPS65219 series of PMICs have 3 single phase BUCKs & 4 LDOs
1547 TPS6594 series of PMICs have 5 BUCKs and 4 LDOs
1549 BUCKs 1,2,3,4 can be used in single phase or multiphase mode.
|
| H A D | da9063-regulator.c | 32 /* BUCKs */
44 /* When two BUCKs are merged, they cannot be reused separately */
110 /* Macros for voltage DC/DC converters (BUCKs) */
251 * Bucks use single mode register field for normal operation
921 "Error while reading BUCKs configuration\n"); in da9063_regulator_probe()
|
| /openbmc/linux/include/linux/mfd/ |
| H A D | 88pm80x.h | 54 #define PM800_MAX_REGULATOR PM800_ID_RG_MAX /* 5 Bucks, 19 LDOs */
55 #define PM800_NUM_BUCK (5) /*5 Bucks */
56 #define PM800_NUM_LDO (19) /*19 Bucks */
|
| /openbmc/linux/include/linux/regulator/ |
| H A D | mt6357-regulator.h | 10 /* Bucks */
|
| /openbmc/u-boot/drivers/power/pmic/ |
| H A D | Kconfig | 176 The S5M8767 PMIC provides a large array of LDOs and BUCKs for use
238 The STPMU1 PMIC provides 4 BUCKs, 6 LDOs, 1 VREF and 2 power switches.
|
| /openbmc/linux/Documentation/devicetree/bindings/usb/ |
| H A D | mediatek,mt6360-tcpc.yaml | 14 regulators (BUCKs/LDOs), and TypeC Port Switch with Power Delivery controller.
|