1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * Copyright 2015 Freescale Semiconductor, Inc.
4 *
5 * DWC3 controller driver
6 *
7 * Author: Ramneek Mehresh<ramneek.mehresh@freescale.com>
8 */
9
10 #include <common.h>
11 #include <dm.h>
12 #include <fdtdec.h>
13 #include <generic-phy.h>
14 #include <usb.h>
15 #include <dwc3-uboot.h>
16
17 #include "xhci.h"
18 #include <asm/io.h>
19 #include <linux/usb/dwc3.h>
20 #include <linux/usb/otg.h>
21
22 struct xhci_dwc3_platdata {
23 struct phy *usb_phys;
24 int num_phys;
25 };
26
dwc3_set_mode(struct dwc3 * dwc3_reg,u32 mode)27 void dwc3_set_mode(struct dwc3 *dwc3_reg, u32 mode)
28 {
29 clrsetbits_le32(&dwc3_reg->g_ctl,
30 DWC3_GCTL_PRTCAPDIR(DWC3_GCTL_PRTCAP_OTG),
31 DWC3_GCTL_PRTCAPDIR(mode));
32 }
33
dwc3_phy_reset(struct dwc3 * dwc3_reg)34 static void dwc3_phy_reset(struct dwc3 *dwc3_reg)
35 {
36 /* Assert USB3 PHY reset */
37 setbits_le32(&dwc3_reg->g_usb3pipectl[0], DWC3_GUSB3PIPECTL_PHYSOFTRST);
38
39 /* Assert USB2 PHY reset */
40 setbits_le32(&dwc3_reg->g_usb2phycfg, DWC3_GUSB2PHYCFG_PHYSOFTRST);
41
42 mdelay(100);
43
44 /* Clear USB3 PHY reset */
45 clrbits_le32(&dwc3_reg->g_usb3pipectl[0], DWC3_GUSB3PIPECTL_PHYSOFTRST);
46
47 /* Clear USB2 PHY reset */
48 clrbits_le32(&dwc3_reg->g_usb2phycfg, DWC3_GUSB2PHYCFG_PHYSOFTRST);
49 }
50
dwc3_core_soft_reset(struct dwc3 * dwc3_reg)51 void dwc3_core_soft_reset(struct dwc3 *dwc3_reg)
52 {
53 /* Before Resetting PHY, put Core in Reset */
54 setbits_le32(&dwc3_reg->g_ctl, DWC3_GCTL_CORESOFTRESET);
55
56 /* reset USB3 phy - if required */
57 dwc3_phy_reset(dwc3_reg);
58
59 mdelay(100);
60
61 /* After PHYs are stable we can take Core out of reset state */
62 clrbits_le32(&dwc3_reg->g_ctl, DWC3_GCTL_CORESOFTRESET);
63 }
64
dwc3_core_init(struct dwc3 * dwc3_reg)65 int dwc3_core_init(struct dwc3 *dwc3_reg)
66 {
67 u32 reg;
68 u32 revision;
69 unsigned int dwc3_hwparams1;
70
71 revision = readl(&dwc3_reg->g_snpsid);
72 /* This should read as U3 followed by revision number */
73 if ((revision & DWC3_GSNPSID_MASK) != 0x55330000) {
74 puts("this is not a DesignWare USB3 DRD Core\n");
75 return -1;
76 }
77
78 dwc3_core_soft_reset(dwc3_reg);
79
80 dwc3_hwparams1 = readl(&dwc3_reg->g_hwparams1);
81
82 reg = readl(&dwc3_reg->g_ctl);
83 reg &= ~DWC3_GCTL_SCALEDOWN_MASK;
84 reg &= ~DWC3_GCTL_DISSCRAMBLE;
85 switch (DWC3_GHWPARAMS1_EN_PWROPT(dwc3_hwparams1)) {
86 case DWC3_GHWPARAMS1_EN_PWROPT_CLK:
87 reg &= ~DWC3_GCTL_DSBLCLKGTNG;
88 break;
89 default:
90 debug("No power optimization available\n");
91 }
92
93 /*
94 * WORKAROUND: DWC3 revisions <1.90a have a bug
95 * where the device can fail to connect at SuperSpeed
96 * and falls back to high-speed mode which causes
97 * the device to enter a Connect/Disconnect loop
98 */
99 if ((revision & DWC3_REVISION_MASK) < 0x190a)
100 reg |= DWC3_GCTL_U2RSTECN;
101
102 writel(reg, &dwc3_reg->g_ctl);
103
104 return 0;
105 }
106
dwc3_set_fladj(struct dwc3 * dwc3_reg,u32 val)107 void dwc3_set_fladj(struct dwc3 *dwc3_reg, u32 val)
108 {
109 setbits_le32(&dwc3_reg->g_fladj, GFLADJ_30MHZ_REG_SEL |
110 GFLADJ_30MHZ(val));
111 }
112
113 #if CONFIG_IS_ENABLED(DM_USB)
xhci_dwc3_probe(struct udevice * dev)114 static int xhci_dwc3_probe(struct udevice *dev)
115 {
116 struct xhci_hcor *hcor;
117 struct xhci_hccr *hccr;
118 struct dwc3 *dwc3_reg;
119 enum usb_dr_mode dr_mode;
120 struct xhci_dwc3_platdata *plat = dev_get_platdata(dev);
121 int ret;
122
123 hccr = (struct xhci_hccr *)((uintptr_t)dev_read_addr(dev));
124 hcor = (struct xhci_hcor *)((uintptr_t)hccr +
125 HC_LENGTH(xhci_readl(&(hccr)->cr_capbase)));
126
127 ret = dwc3_setup_phy(dev, &plat->usb_phys, &plat->num_phys);
128 if (ret && (ret != -ENOTSUPP))
129 return ret;
130
131 dwc3_reg = (struct dwc3 *)((char *)(hccr) + DWC3_REG_OFFSET);
132
133 dwc3_core_init(dwc3_reg);
134
135 dr_mode = usb_get_dr_mode(dev_of_offset(dev));
136 if (dr_mode == USB_DR_MODE_UNKNOWN)
137 /* by default set dual role mode to HOST */
138 dr_mode = USB_DR_MODE_HOST;
139
140 dwc3_set_mode(dwc3_reg, dr_mode);
141
142 return xhci_register(dev, hccr, hcor);
143 }
144
xhci_dwc3_remove(struct udevice * dev)145 static int xhci_dwc3_remove(struct udevice *dev)
146 {
147 struct xhci_dwc3_platdata *plat = dev_get_platdata(dev);
148
149 dwc3_shutdown_phy(dev, plat->usb_phys, plat->num_phys);
150
151 return xhci_deregister(dev);
152 }
153
154 static const struct udevice_id xhci_dwc3_ids[] = {
155 { .compatible = "snps,dwc3" },
156 { }
157 };
158
159 U_BOOT_DRIVER(xhci_dwc3) = {
160 .name = "xhci-dwc3",
161 .id = UCLASS_USB,
162 .of_match = xhci_dwc3_ids,
163 .probe = xhci_dwc3_probe,
164 .remove = xhci_dwc3_remove,
165 .ops = &xhci_usb_ops,
166 .priv_auto_alloc_size = sizeof(struct xhci_ctrl),
167 .platdata_auto_alloc_size = sizeof(struct xhci_dwc3_platdata),
168 .flags = DM_FLAG_ALLOC_PRIV_DMA,
169 };
170 #endif
171