1 /*
2 drivers/net/ethernet/dec/tulip/media.c
3
4 Copyright 2000,2001 The Linux Kernel Team
5 Written/copyright 1994-2001 by Donald Becker.
6
7 This software may be used and distributed according to the terms
8 of the GNU General Public License, incorporated herein by reference.
9
10 Please submit bugs to http://bugzilla.kernel.org/ .
11 */
12
13 #include <linux/kernel.h>
14 #include <linux/mii.h>
15 #include <linux/delay.h>
16 #include <linux/pci.h>
17 #include "tulip.h"
18
19
20 /* The maximum data clock rate is 2.5 Mhz. The minimum timing is usually
21 met by back-to-back PCI I/O cycles, but we insert a delay to avoid
22 "overclocking" issues or future 66Mhz PCI. */
23 #define mdio_delay() ioread32(mdio_addr)
24
25 /* Read and write the MII registers using software-generated serial
26 MDIO protocol. It is just different enough from the EEPROM protocol
27 to not share code. The maxium data clock rate is 2.5 Mhz. */
28 #define MDIO_SHIFT_CLK 0x10000
29 #define MDIO_DATA_WRITE0 0x00000
30 #define MDIO_DATA_WRITE1 0x20000
31 #define MDIO_ENB 0x00000 /* Ignore the 0x02000 databook setting. */
32 #define MDIO_ENB_IN 0x40000
33 #define MDIO_DATA_READ 0x80000
34
35 static const unsigned char comet_miireg2offset[32] = {
36 0xB4, 0xB8, 0xBC, 0xC0, 0xC4, 0xC8, 0xCC, 0, 0,0,0,0, 0,0,0,0,
37 0,0xD0,0,0, 0,0,0,0, 0,0,0,0, 0, 0xD4, 0xD8, 0xDC, };
38
39
40 /* MII transceiver control section.
41 Read and write the MII registers using software-generated serial
42 MDIO protocol.
43 See IEEE 802.3-2002.pdf (Section 2, Chapter "22.2.4 Management functions")
44 or DP83840A data sheet for more details.
45 */
46
tulip_mdio_read(struct net_device * dev,int phy_id,int location)47 int tulip_mdio_read(struct net_device *dev, int phy_id, int location)
48 {
49 struct tulip_private *tp = netdev_priv(dev);
50 int i;
51 int read_cmd = (0xf6 << 10) | ((phy_id & 0x1f) << 5) | location;
52 int retval = 0;
53 void __iomem *ioaddr = tp->base_addr;
54 void __iomem *mdio_addr = ioaddr + CSR9;
55 unsigned long flags;
56
57 if (location & ~0x1f)
58 return 0xffff;
59
60 if (tp->chip_id == COMET && phy_id == 30) {
61 if (comet_miireg2offset[location])
62 return ioread32(ioaddr + comet_miireg2offset[location]);
63 return 0xffff;
64 }
65
66 spin_lock_irqsave(&tp->mii_lock, flags);
67 if (tp->chip_id == LC82C168) {
68 iowrite32(0x60020000 + (phy_id<<23) + (location<<18), ioaddr + 0xA0);
69 ioread32(ioaddr + 0xA0);
70 ioread32(ioaddr + 0xA0);
71 for (i = 1000; i >= 0; --i) {
72 barrier();
73 if ( ! ((retval = ioread32(ioaddr + 0xA0)) & 0x80000000))
74 break;
75 }
76 spin_unlock_irqrestore(&tp->mii_lock, flags);
77 return retval & 0xffff;
78 }
79
80 /* Establish sync by sending at least 32 logic ones. */
81 for (i = 32; i >= 0; i--) {
82 iowrite32(MDIO_ENB | MDIO_DATA_WRITE1, mdio_addr);
83 mdio_delay();
84 iowrite32(MDIO_ENB | MDIO_DATA_WRITE1 | MDIO_SHIFT_CLK, mdio_addr);
85 mdio_delay();
86 }
87 /* Shift the read command bits out. */
88 for (i = 15; i >= 0; i--) {
89 int dataval = (read_cmd & (1 << i)) ? MDIO_DATA_WRITE1 : 0;
90
91 iowrite32(MDIO_ENB | dataval, mdio_addr);
92 mdio_delay();
93 iowrite32(MDIO_ENB | dataval | MDIO_SHIFT_CLK, mdio_addr);
94 mdio_delay();
95 }
96 /* Read the two transition, 16 data, and wire-idle bits. */
97 for (i = 19; i > 0; i--) {
98 iowrite32(MDIO_ENB_IN, mdio_addr);
99 mdio_delay();
100 retval = (retval << 1) | ((ioread32(mdio_addr) & MDIO_DATA_READ) ? 1 : 0);
101 iowrite32(MDIO_ENB_IN | MDIO_SHIFT_CLK, mdio_addr);
102 mdio_delay();
103 }
104
105 spin_unlock_irqrestore(&tp->mii_lock, flags);
106 return (retval>>1) & 0xffff;
107 }
108
tulip_mdio_write(struct net_device * dev,int phy_id,int location,int val)109 void tulip_mdio_write(struct net_device *dev, int phy_id, int location, int val)
110 {
111 struct tulip_private *tp = netdev_priv(dev);
112 int i;
113 int cmd = (0x5002 << 16) | ((phy_id & 0x1f) << 23) | (location<<18) | (val & 0xffff);
114 void __iomem *ioaddr = tp->base_addr;
115 void __iomem *mdio_addr = ioaddr + CSR9;
116 unsigned long flags;
117
118 if (location & ~0x1f)
119 return;
120
121 if (tp->chip_id == COMET && phy_id == 30) {
122 if (comet_miireg2offset[location])
123 iowrite32(val, ioaddr + comet_miireg2offset[location]);
124 return;
125 }
126
127 spin_lock_irqsave(&tp->mii_lock, flags);
128 if (tp->chip_id == LC82C168) {
129 iowrite32(cmd, ioaddr + 0xA0);
130 for (i = 1000; i >= 0; --i) {
131 barrier();
132 if ( ! (ioread32(ioaddr + 0xA0) & 0x80000000))
133 break;
134 }
135 spin_unlock_irqrestore(&tp->mii_lock, flags);
136 return;
137 }
138
139 /* Establish sync by sending 32 logic ones. */
140 for (i = 32; i >= 0; i--) {
141 iowrite32(MDIO_ENB | MDIO_DATA_WRITE1, mdio_addr);
142 mdio_delay();
143 iowrite32(MDIO_ENB | MDIO_DATA_WRITE1 | MDIO_SHIFT_CLK, mdio_addr);
144 mdio_delay();
145 }
146 /* Shift the command bits out. */
147 for (i = 31; i >= 0; i--) {
148 int dataval = (cmd & (1 << i)) ? MDIO_DATA_WRITE1 : 0;
149 iowrite32(MDIO_ENB | dataval, mdio_addr);
150 mdio_delay();
151 iowrite32(MDIO_ENB | dataval | MDIO_SHIFT_CLK, mdio_addr);
152 mdio_delay();
153 }
154 /* Clear out extra bits. */
155 for (i = 2; i > 0; i--) {
156 iowrite32(MDIO_ENB_IN, mdio_addr);
157 mdio_delay();
158 iowrite32(MDIO_ENB_IN | MDIO_SHIFT_CLK, mdio_addr);
159 mdio_delay();
160 }
161
162 spin_unlock_irqrestore(&tp->mii_lock, flags);
163 }
164
165
166 /* Set up the transceiver control registers for the selected media type. */
tulip_select_media(struct net_device * dev,int startup)167 void tulip_select_media(struct net_device *dev, int startup)
168 {
169 struct tulip_private *tp = netdev_priv(dev);
170 void __iomem *ioaddr = tp->base_addr;
171 struct mediatable *mtable = tp->mtable;
172 u32 new_csr6;
173 int i;
174
175 if (mtable) {
176 struct medialeaf *mleaf = &mtable->mleaf[tp->cur_index];
177 unsigned char *p = mleaf->leafdata;
178 switch (mleaf->type) {
179 case 0: /* 21140 non-MII xcvr. */
180 if (tulip_debug > 1)
181 netdev_dbg(dev, "Using a 21140 non-MII transceiver with control setting %02x\n",
182 p[1]);
183 dev->if_port = p[0];
184 if (startup)
185 iowrite32(mtable->csr12dir | 0x100, ioaddr + CSR12);
186 iowrite32(p[1], ioaddr + CSR12);
187 new_csr6 = 0x02000000 | ((p[2] & 0x71) << 18);
188 break;
189 case 2: case 4: {
190 u16 setup[5];
191 u32 csr13val, csr14val, csr15dir, csr15val;
192 for (i = 0; i < 5; i++)
193 setup[i] = get_u16(&p[i*2 + 1]);
194
195 dev->if_port = p[0] & MEDIA_MASK;
196 if (tulip_media_cap[dev->if_port] & MediaAlwaysFD)
197 tp->full_duplex = 1;
198
199 if (startup && mtable->has_reset) {
200 struct medialeaf *rleaf = &mtable->mleaf[mtable->has_reset];
201 unsigned char *rst = rleaf->leafdata;
202 if (tulip_debug > 1)
203 netdev_dbg(dev, "Resetting the transceiver\n");
204 for (i = 0; i < rst[0]; i++)
205 iowrite32(get_u16(rst + 1 + (i<<1)) << 16, ioaddr + CSR15);
206 }
207 if (tulip_debug > 1)
208 netdev_dbg(dev, "21143 non-MII %s transceiver control %04x/%04x\n",
209 medianame[dev->if_port],
210 setup[0], setup[1]);
211 if (p[0] & 0x40) { /* SIA (CSR13-15) setup values are provided. */
212 csr13val = setup[0];
213 csr14val = setup[1];
214 csr15dir = (setup[3]<<16) | setup[2];
215 csr15val = (setup[4]<<16) | setup[2];
216 iowrite32(0, ioaddr + CSR13);
217 iowrite32(csr14val, ioaddr + CSR14);
218 iowrite32(csr15dir, ioaddr + CSR15); /* Direction */
219 iowrite32(csr15val, ioaddr + CSR15); /* Data */
220 iowrite32(csr13val, ioaddr + CSR13);
221 } else {
222 csr13val = 1;
223 csr14val = 0;
224 csr15dir = (setup[0]<<16) | 0x0008;
225 csr15val = (setup[1]<<16) | 0x0008;
226 if (dev->if_port <= 4)
227 csr14val = t21142_csr14[dev->if_port];
228 if (startup) {
229 iowrite32(0, ioaddr + CSR13);
230 iowrite32(csr14val, ioaddr + CSR14);
231 }
232 iowrite32(csr15dir, ioaddr + CSR15); /* Direction */
233 iowrite32(csr15val, ioaddr + CSR15); /* Data */
234 if (startup) iowrite32(csr13val, ioaddr + CSR13);
235 }
236 if (tulip_debug > 1)
237 netdev_dbg(dev, "Setting CSR15 to %08x/%08x\n",
238 csr15dir, csr15val);
239 if (mleaf->type == 4)
240 new_csr6 = 0x82020000 | ((setup[2] & 0x71) << 18);
241 else
242 new_csr6 = 0x82420000;
243 break;
244 }
245 case 1: case 3: {
246 int phy_num = p[0];
247 int init_length = p[1];
248 u16 *misc_info, tmp_info;
249
250 dev->if_port = 11;
251 new_csr6 = 0x020E0000;
252 if (mleaf->type == 3) { /* 21142 */
253 u16 *init_sequence = (u16*)(p+2);
254 u16 *reset_sequence = &((u16*)(p+3))[init_length];
255 int reset_length = p[2 + init_length*2];
256 misc_info = reset_sequence + reset_length;
257 if (startup) {
258 int timeout = 10; /* max 1 ms */
259 for (i = 0; i < reset_length; i++)
260 iowrite32(get_u16(&reset_sequence[i]) << 16, ioaddr + CSR15);
261
262 /* flush posted writes */
263 ioread32(ioaddr + CSR15);
264
265 /* Sect 3.10.3 in DP83840A.pdf (p39) */
266 udelay(500);
267
268 /* Section 4.2 in DP83840A.pdf (p43) */
269 /* and IEEE 802.3 "22.2.4.1.1 Reset" */
270 while (timeout-- &&
271 (tulip_mdio_read (dev, phy_num, MII_BMCR) & BMCR_RESET))
272 udelay(100);
273 }
274 for (i = 0; i < init_length; i++)
275 iowrite32(get_u16(&init_sequence[i]) << 16, ioaddr + CSR15);
276
277 ioread32(ioaddr + CSR15); /* flush posted writes */
278 } else {
279 u8 *init_sequence = p + 2;
280 u8 *reset_sequence = p + 3 + init_length;
281 int reset_length = p[2 + init_length];
282 misc_info = (u16*)(reset_sequence + reset_length);
283 if (startup) {
284 int timeout = 10; /* max 1 ms */
285 iowrite32(mtable->csr12dir | 0x100, ioaddr + CSR12);
286 for (i = 0; i < reset_length; i++)
287 iowrite32(reset_sequence[i], ioaddr + CSR12);
288
289 /* flush posted writes */
290 ioread32(ioaddr + CSR12);
291
292 /* Sect 3.10.3 in DP83840A.pdf (p39) */
293 udelay(500);
294
295 /* Section 4.2 in DP83840A.pdf (p43) */
296 /* and IEEE 802.3 "22.2.4.1.1 Reset" */
297 while (timeout-- &&
298 (tulip_mdio_read (dev, phy_num, MII_BMCR) & BMCR_RESET))
299 udelay(100);
300 }
301 for (i = 0; i < init_length; i++)
302 iowrite32(init_sequence[i], ioaddr + CSR12);
303
304 ioread32(ioaddr + CSR12); /* flush posted writes */
305 }
306
307 tmp_info = get_u16(&misc_info[1]);
308 if (tmp_info)
309 tp->advertising[phy_num] = tmp_info | 1;
310 if (tmp_info && startup < 2) {
311 if (tp->mii_advertise == 0)
312 tp->mii_advertise = tp->advertising[phy_num];
313 if (tulip_debug > 1)
314 netdev_dbg(dev, " Advertising %04x on MII %d\n",
315 tp->mii_advertise,
316 tp->phys[phy_num]);
317 tulip_mdio_write(dev, tp->phys[phy_num], 4, tp->mii_advertise);
318 }
319 break;
320 }
321 case 5: case 6: {
322 new_csr6 = 0; /* FIXME */
323
324 if (startup && mtable->has_reset) {
325 struct medialeaf *rleaf = &mtable->mleaf[mtable->has_reset];
326 unsigned char *rst = rleaf->leafdata;
327 if (tulip_debug > 1)
328 netdev_dbg(dev, "Resetting the transceiver\n");
329 for (i = 0; i < rst[0]; i++)
330 iowrite32(get_u16(rst + 1 + (i<<1)) << 16, ioaddr + CSR15);
331 }
332
333 break;
334 }
335 default:
336 netdev_dbg(dev, " Invalid media table selection %d\n",
337 mleaf->type);
338 new_csr6 = 0x020E0000;
339 }
340 if (tulip_debug > 1)
341 netdev_dbg(dev, "Using media type %s, CSR12 is %02x\n",
342 medianame[dev->if_port],
343 ioread32(ioaddr + CSR12) & 0xff);
344 } else if (tp->chip_id == LC82C168) {
345 if (startup && ! tp->medialock)
346 dev->if_port = tp->mii_cnt ? 11 : 0;
347 if (tulip_debug > 1)
348 netdev_dbg(dev, "PNIC PHY status is %3.3x, media %s\n",
349 ioread32(ioaddr + 0xB8),
350 medianame[dev->if_port]);
351 if (tp->mii_cnt) {
352 new_csr6 = 0x810C0000;
353 iowrite32(0x0001, ioaddr + CSR15);
354 iowrite32(0x0201B07A, ioaddr + 0xB8);
355 } else if (startup) {
356 /* Start with 10mbps to do autonegotiation. */
357 iowrite32(0x32, ioaddr + CSR12);
358 new_csr6 = 0x00420000;
359 iowrite32(0x0001B078, ioaddr + 0xB8);
360 iowrite32(0x0201B078, ioaddr + 0xB8);
361 } else if (dev->if_port == 3 || dev->if_port == 5) {
362 iowrite32(0x33, ioaddr + CSR12);
363 new_csr6 = 0x01860000;
364 /* Trigger autonegotiation. */
365 iowrite32(0x0001F868, ioaddr + 0xB8);
366 } else {
367 iowrite32(0x32, ioaddr + CSR12);
368 new_csr6 = 0x00420000;
369 iowrite32(0x1F078, ioaddr + 0xB8);
370 }
371 } else { /* Unknown chip type with no media table. */
372 if (tp->default_port == 0)
373 dev->if_port = tp->mii_cnt ? 11 : 3;
374 if (tulip_media_cap[dev->if_port] & MediaIsMII) {
375 new_csr6 = 0x020E0000;
376 } else if (tulip_media_cap[dev->if_port] & MediaIsFx) {
377 new_csr6 = 0x02860000;
378 } else
379 new_csr6 = 0x03860000;
380 if (tulip_debug > 1)
381 netdev_dbg(dev, "No media description table, assuming %s transceiver, CSR12 %02x\n",
382 medianame[dev->if_port],
383 ioread32(ioaddr + CSR12));
384 }
385
386 tp->csr6 = new_csr6 | (tp->csr6 & 0xfdff) | (tp->full_duplex ? 0x0200 : 0);
387
388 mdelay(1);
389 }
390
391 /*
392 Check the MII negotiated duplex and change the CSR6 setting if
393 required.
394 Return 0 if everything is OK.
395 Return < 0 if the transceiver is missing or has no link beat.
396 */
tulip_check_duplex(struct net_device * dev)397 int tulip_check_duplex(struct net_device *dev)
398 {
399 struct tulip_private *tp = netdev_priv(dev);
400 unsigned int bmsr, lpa, negotiated, new_csr6;
401
402 bmsr = tulip_mdio_read(dev, tp->phys[0], MII_BMSR);
403 lpa = tulip_mdio_read(dev, tp->phys[0], MII_LPA);
404 if (tulip_debug > 1)
405 dev_info(&dev->dev, "MII status %04x, Link partner report %04x\n",
406 bmsr, lpa);
407 if (bmsr == 0xffff)
408 return -2;
409 if ((bmsr & BMSR_LSTATUS) == 0) {
410 int new_bmsr = tulip_mdio_read(dev, tp->phys[0], MII_BMSR);
411 if ((new_bmsr & BMSR_LSTATUS) == 0) {
412 if (tulip_debug > 1)
413 dev_info(&dev->dev,
414 "No link beat on the MII interface, status %04x\n",
415 new_bmsr);
416 return -1;
417 }
418 }
419 negotiated = lpa & tp->advertising[0];
420 tp->full_duplex = mii_duplex(tp->full_duplex_lock, negotiated);
421
422 new_csr6 = tp->csr6;
423
424 if (negotiated & LPA_100) new_csr6 &= ~TxThreshold;
425 else new_csr6 |= TxThreshold;
426 if (tp->full_duplex) new_csr6 |= FullDuplex;
427 else new_csr6 &= ~FullDuplex;
428
429 if (new_csr6 != tp->csr6) {
430 tp->csr6 = new_csr6;
431 tulip_restart_rxtx(tp);
432
433 if (tulip_debug > 0)
434 dev_info(&dev->dev,
435 "Setting %s-duplex based on MII#%d link partner capability of %04x\n",
436 tp->full_duplex ? "full" : "half",
437 tp->phys[0], lpa);
438 return 1;
439 }
440
441 return 0;
442 }
443
tulip_find_mii(struct net_device * dev,int board_idx)444 void tulip_find_mii(struct net_device *dev, int board_idx)
445 {
446 struct tulip_private *tp = netdev_priv(dev);
447 int phyn, phy_idx = 0;
448 int mii_reg0;
449 int mii_advert;
450 unsigned int to_advert, new_bmcr, ane_switch;
451
452 /* Find the connected MII xcvrs.
453 Doing this in open() would allow detecting external xcvrs later,
454 but takes much time. */
455 for (phyn = 1; phyn <= 32 && phy_idx < ARRAY_SIZE(tp->phys); phyn++) {
456 int phy = phyn & 0x1f;
457 int mii_status = tulip_mdio_read (dev, phy, MII_BMSR);
458 if ((mii_status & 0x8301) == 0x8001 ||
459 ((mii_status & BMSR_100BASE4) == 0 &&
460 (mii_status & 0x7800) != 0)) {
461 /* preserve Becker logic, gain indentation level */
462 } else {
463 continue;
464 }
465
466 mii_reg0 = tulip_mdio_read (dev, phy, MII_BMCR);
467 mii_advert = tulip_mdio_read (dev, phy, MII_ADVERTISE);
468 ane_switch = 0;
469
470 /* if not advertising at all, gen an
471 * advertising value from the capability
472 * bits in BMSR
473 */
474 if ((mii_advert & ADVERTISE_ALL) == 0) {
475 unsigned int tmpadv = tulip_mdio_read (dev, phy, MII_BMSR);
476 mii_advert = ((tmpadv >> 6) & 0x3e0) | 1;
477 }
478
479 if (tp->mii_advertise) {
480 tp->advertising[phy_idx] =
481 to_advert = tp->mii_advertise;
482 } else if (tp->advertising[phy_idx]) {
483 to_advert = tp->advertising[phy_idx];
484 } else {
485 tp->advertising[phy_idx] =
486 tp->mii_advertise =
487 to_advert = mii_advert;
488 }
489
490 tp->phys[phy_idx++] = phy;
491
492 pr_info("tulip%d: MII transceiver #%d config %04x status %04x advertising %04x\n",
493 board_idx, phy, mii_reg0, mii_status, mii_advert);
494
495 /* Fixup for DLink with miswired PHY. */
496 if (mii_advert != to_advert) {
497 pr_debug("tulip%d: Advertising %04x on PHY %d, previously advertising %04x\n",
498 board_idx, to_advert, phy, mii_advert);
499 tulip_mdio_write (dev, phy, 4, to_advert);
500 }
501
502 /* Enable autonegotiation: some boards default to off. */
503 if (tp->default_port == 0) {
504 new_bmcr = mii_reg0 | BMCR_ANENABLE;
505 if (new_bmcr != mii_reg0) {
506 new_bmcr |= BMCR_ANRESTART;
507 ane_switch = 1;
508 }
509 }
510 /* ...or disable nway, if forcing media */
511 else {
512 new_bmcr = mii_reg0 & ~BMCR_ANENABLE;
513 if (new_bmcr != mii_reg0)
514 ane_switch = 1;
515 }
516
517 /* clear out bits we never want at this point */
518 new_bmcr &= ~(BMCR_CTST | BMCR_FULLDPLX | BMCR_ISOLATE |
519 BMCR_PDOWN | BMCR_SPEED100 | BMCR_LOOPBACK |
520 BMCR_RESET);
521
522 if (tp->full_duplex)
523 new_bmcr |= BMCR_FULLDPLX;
524 if (tulip_media_cap[tp->default_port] & MediaIs100)
525 new_bmcr |= BMCR_SPEED100;
526
527 if (new_bmcr != mii_reg0) {
528 /* some phys need the ANE switch to
529 * happen before forced media settings
530 * will "take." However, we write the
531 * same value twice in order not to
532 * confuse the sane phys.
533 */
534 if (ane_switch) {
535 tulip_mdio_write (dev, phy, MII_BMCR, new_bmcr);
536 udelay (10);
537 }
538 tulip_mdio_write (dev, phy, MII_BMCR, new_bmcr);
539 }
540 }
541 tp->mii_cnt = phy_idx;
542 if (tp->mtable && tp->mtable->has_mii && phy_idx == 0) {
543 pr_info("tulip%d: ***WARNING***: No MII transceiver found!\n",
544 board_idx);
545 tp->phys[0] = 1;
546 }
547 }
548