1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * linux/drivers/mmc/host/pxa.c - PXA MMCI driver
4 *
5 * Copyright (C) 2003 Russell King, All Rights Reserved.
6 *
7 * This hardware is really sick:
8 * - No way to clear interrupts.
9 * - Have to turn off the clock whenever we touch the device.
10 * - Doesn't tell you how many data blocks were transferred.
11 * Yuck!
12 *
13 * 1 and 3 byte data transfers not supported
14 * max block length up to 1023
15 */
16 #include <linux/module.h>
17 #include <linux/init.h>
18 #include <linux/ioport.h>
19 #include <linux/platform_device.h>
20 #include <linux/delay.h>
21 #include <linux/interrupt.h>
22 #include <linux/dmaengine.h>
23 #include <linux/dma-mapping.h>
24 #include <linux/clk.h>
25 #include <linux/err.h>
26 #include <linux/mmc/host.h>
27 #include <linux/mmc/slot-gpio.h>
28 #include <linux/io.h>
29 #include <linux/regulator/consumer.h>
30 #include <linux/gpio/consumer.h>
31 #include <linux/gfp.h>
32 #include <linux/of.h>
33 #include <linux/soc/pxa/cpu.h>
34
35 #include <linux/sizes.h>
36
37 #include <linux/platform_data/mmc-pxamci.h>
38
39 #include "pxamci.h"
40
41 #define DRIVER_NAME "pxa2xx-mci"
42
43 #define NR_SG 1
44 #define CLKRT_OFF (~0)
45
46 #define mmc_has_26MHz() (cpu_is_pxa300() || cpu_is_pxa310() \
47 || cpu_is_pxa935())
48
49 struct pxamci_host {
50 struct mmc_host *mmc;
51 spinlock_t lock;
52 struct resource *res;
53 void __iomem *base;
54 struct clk *clk;
55 unsigned long clkrate;
56 unsigned int clkrt;
57 unsigned int cmdat;
58 unsigned int imask;
59 unsigned int power_mode;
60 unsigned long detect_delay_ms;
61 bool use_ro_gpio;
62 struct gpio_desc *power;
63 struct pxamci_platform_data *pdata;
64
65 struct mmc_request *mrq;
66 struct mmc_command *cmd;
67 struct mmc_data *data;
68
69 struct dma_chan *dma_chan_rx;
70 struct dma_chan *dma_chan_tx;
71 dma_cookie_t dma_cookie;
72 unsigned int dma_len;
73 unsigned int dma_dir;
74 };
75
pxamci_init_ocr(struct pxamci_host * host)76 static int pxamci_init_ocr(struct pxamci_host *host)
77 {
78 struct mmc_host *mmc = host->mmc;
79 int ret;
80
81 ret = mmc_regulator_get_supply(mmc);
82 if (ret < 0)
83 return ret;
84
85 if (IS_ERR(mmc->supply.vmmc)) {
86 /* fall-back to platform data */
87 mmc->ocr_avail = host->pdata ?
88 host->pdata->ocr_mask :
89 MMC_VDD_32_33 | MMC_VDD_33_34;
90 }
91
92 return 0;
93 }
94
pxamci_set_power(struct pxamci_host * host,unsigned char power_mode,unsigned int vdd)95 static inline int pxamci_set_power(struct pxamci_host *host,
96 unsigned char power_mode,
97 unsigned int vdd)
98 {
99 struct mmc_host *mmc = host->mmc;
100 struct regulator *supply = mmc->supply.vmmc;
101
102 if (!IS_ERR(supply))
103 return mmc_regulator_set_ocr(mmc, supply, vdd);
104
105 if (host->power) {
106 bool on = !!((1 << vdd) & host->pdata->ocr_mask);
107 gpiod_set_value(host->power, on);
108 }
109
110 if (host->pdata && host->pdata->setpower)
111 return host->pdata->setpower(mmc_dev(host->mmc), vdd);
112
113 return 0;
114 }
115
pxamci_stop_clock(struct pxamci_host * host)116 static void pxamci_stop_clock(struct pxamci_host *host)
117 {
118 if (readl(host->base + MMC_STAT) & STAT_CLK_EN) {
119 unsigned long timeout = 10000;
120 unsigned int v;
121
122 writel(STOP_CLOCK, host->base + MMC_STRPCL);
123
124 do {
125 v = readl(host->base + MMC_STAT);
126 if (!(v & STAT_CLK_EN))
127 break;
128 udelay(1);
129 } while (timeout--);
130
131 if (v & STAT_CLK_EN)
132 dev_err(mmc_dev(host->mmc), "unable to stop clock\n");
133 }
134 }
135
pxamci_enable_irq(struct pxamci_host * host,unsigned int mask)136 static void pxamci_enable_irq(struct pxamci_host *host, unsigned int mask)
137 {
138 unsigned long flags;
139
140 spin_lock_irqsave(&host->lock, flags);
141 host->imask &= ~mask;
142 writel(host->imask, host->base + MMC_I_MASK);
143 spin_unlock_irqrestore(&host->lock, flags);
144 }
145
pxamci_disable_irq(struct pxamci_host * host,unsigned int mask)146 static void pxamci_disable_irq(struct pxamci_host *host, unsigned int mask)
147 {
148 unsigned long flags;
149
150 spin_lock_irqsave(&host->lock, flags);
151 host->imask |= mask;
152 writel(host->imask, host->base + MMC_I_MASK);
153 spin_unlock_irqrestore(&host->lock, flags);
154 }
155
156 static void pxamci_dma_irq(void *param);
157
pxamci_setup_data(struct pxamci_host * host,struct mmc_data * data)158 static void pxamci_setup_data(struct pxamci_host *host, struct mmc_data *data)
159 {
160 struct dma_async_tx_descriptor *tx;
161 enum dma_transfer_direction direction;
162 struct dma_slave_config config;
163 struct dma_chan *chan;
164 unsigned int nob = data->blocks;
165 unsigned long long clks;
166 unsigned int timeout;
167 int ret;
168
169 host->data = data;
170
171 writel(nob, host->base + MMC_NOB);
172 writel(data->blksz, host->base + MMC_BLKLEN);
173
174 clks = (unsigned long long)data->timeout_ns * host->clkrate;
175 do_div(clks, 1000000000UL);
176 timeout = (unsigned int)clks + (data->timeout_clks << host->clkrt);
177 writel((timeout + 255) / 256, host->base + MMC_RDTO);
178
179 memset(&config, 0, sizeof(config));
180 config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
181 config.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
182 config.src_addr = host->res->start + MMC_RXFIFO;
183 config.dst_addr = host->res->start + MMC_TXFIFO;
184 config.src_maxburst = 32;
185 config.dst_maxburst = 32;
186
187 if (data->flags & MMC_DATA_READ) {
188 host->dma_dir = DMA_FROM_DEVICE;
189 direction = DMA_DEV_TO_MEM;
190 chan = host->dma_chan_rx;
191 } else {
192 host->dma_dir = DMA_TO_DEVICE;
193 direction = DMA_MEM_TO_DEV;
194 chan = host->dma_chan_tx;
195 }
196
197 config.direction = direction;
198
199 ret = dmaengine_slave_config(chan, &config);
200 if (ret < 0) {
201 dev_err(mmc_dev(host->mmc), "dma slave config failed\n");
202 return;
203 }
204
205 host->dma_len = dma_map_sg(chan->device->dev, data->sg, data->sg_len,
206 host->dma_dir);
207
208 tx = dmaengine_prep_slave_sg(chan, data->sg, host->dma_len, direction,
209 DMA_PREP_INTERRUPT);
210 if (!tx) {
211 dev_err(mmc_dev(host->mmc), "prep_slave_sg() failed\n");
212 return;
213 }
214
215 if (!(data->flags & MMC_DATA_READ)) {
216 tx->callback = pxamci_dma_irq;
217 tx->callback_param = host;
218 }
219
220 host->dma_cookie = dmaengine_submit(tx);
221
222 /*
223 * workaround for erratum #91:
224 * only start DMA now if we are doing a read,
225 * otherwise we wait until CMD/RESP has finished
226 * before starting DMA.
227 */
228 if (!cpu_is_pxa27x() || data->flags & MMC_DATA_READ)
229 dma_async_issue_pending(chan);
230 }
231
pxamci_start_cmd(struct pxamci_host * host,struct mmc_command * cmd,unsigned int cmdat)232 static void pxamci_start_cmd(struct pxamci_host *host, struct mmc_command *cmd, unsigned int cmdat)
233 {
234 WARN_ON(host->cmd != NULL);
235 host->cmd = cmd;
236
237 if (cmd->flags & MMC_RSP_BUSY)
238 cmdat |= CMDAT_BUSY;
239
240 #define RSP_TYPE(x) ((x) & ~(MMC_RSP_BUSY|MMC_RSP_OPCODE))
241 switch (RSP_TYPE(mmc_resp_type(cmd))) {
242 case RSP_TYPE(MMC_RSP_R1): /* r1, r1b, r6, r7 */
243 cmdat |= CMDAT_RESP_SHORT;
244 break;
245 case RSP_TYPE(MMC_RSP_R3):
246 cmdat |= CMDAT_RESP_R3;
247 break;
248 case RSP_TYPE(MMC_RSP_R2):
249 cmdat |= CMDAT_RESP_R2;
250 break;
251 default:
252 break;
253 }
254
255 writel(cmd->opcode, host->base + MMC_CMD);
256 writel(cmd->arg >> 16, host->base + MMC_ARGH);
257 writel(cmd->arg & 0xffff, host->base + MMC_ARGL);
258 writel(cmdat, host->base + MMC_CMDAT);
259 writel(host->clkrt, host->base + MMC_CLKRT);
260
261 writel(START_CLOCK, host->base + MMC_STRPCL);
262
263 pxamci_enable_irq(host, END_CMD_RES);
264 }
265
pxamci_finish_request(struct pxamci_host * host,struct mmc_request * mrq)266 static void pxamci_finish_request(struct pxamci_host *host, struct mmc_request *mrq)
267 {
268 host->mrq = NULL;
269 host->cmd = NULL;
270 host->data = NULL;
271 mmc_request_done(host->mmc, mrq);
272 }
273
pxamci_cmd_done(struct pxamci_host * host,unsigned int stat)274 static int pxamci_cmd_done(struct pxamci_host *host, unsigned int stat)
275 {
276 struct mmc_command *cmd = host->cmd;
277 int i;
278 u32 v;
279
280 if (!cmd)
281 return 0;
282
283 host->cmd = NULL;
284
285 /*
286 * Did I mention this is Sick. We always need to
287 * discard the upper 8 bits of the first 16-bit word.
288 */
289 v = readl(host->base + MMC_RES) & 0xffff;
290 for (i = 0; i < 4; i++) {
291 u32 w1 = readl(host->base + MMC_RES) & 0xffff;
292 u32 w2 = readl(host->base + MMC_RES) & 0xffff;
293 cmd->resp[i] = v << 24 | w1 << 8 | w2 >> 8;
294 v = w2;
295 }
296
297 if (stat & STAT_TIME_OUT_RESPONSE) {
298 cmd->error = -ETIMEDOUT;
299 } else if (stat & STAT_RES_CRC_ERR && cmd->flags & MMC_RSP_CRC) {
300 /*
301 * workaround for erratum #42:
302 * Intel PXA27x Family Processor Specification Update Rev 001
303 * A bogus CRC error can appear if the msb of a 136 bit
304 * response is a one.
305 */
306 if (cpu_is_pxa27x() &&
307 (cmd->flags & MMC_RSP_136 && cmd->resp[0] & 0x80000000))
308 pr_debug("ignoring CRC from command %d - *risky*\n", cmd->opcode);
309 else
310 cmd->error = -EILSEQ;
311 }
312
313 pxamci_disable_irq(host, END_CMD_RES);
314 if (host->data && !cmd->error) {
315 pxamci_enable_irq(host, DATA_TRAN_DONE);
316 /*
317 * workaround for erratum #91, if doing write
318 * enable DMA late
319 */
320 if (cpu_is_pxa27x() && host->data->flags & MMC_DATA_WRITE)
321 dma_async_issue_pending(host->dma_chan_tx);
322 } else {
323 pxamci_finish_request(host, host->mrq);
324 }
325
326 return 1;
327 }
328
pxamci_data_done(struct pxamci_host * host,unsigned int stat)329 static int pxamci_data_done(struct pxamci_host *host, unsigned int stat)
330 {
331 struct mmc_data *data = host->data;
332 struct dma_chan *chan;
333
334 if (!data)
335 return 0;
336
337 if (data->flags & MMC_DATA_READ)
338 chan = host->dma_chan_rx;
339 else
340 chan = host->dma_chan_tx;
341 dma_unmap_sg(chan->device->dev,
342 data->sg, data->sg_len, host->dma_dir);
343
344 if (stat & STAT_READ_TIME_OUT)
345 data->error = -ETIMEDOUT;
346 else if (stat & (STAT_CRC_READ_ERROR|STAT_CRC_WRITE_ERROR))
347 data->error = -EILSEQ;
348
349 /*
350 * There appears to be a hardware design bug here. There seems to
351 * be no way to find out how much data was transferred to the card.
352 * This means that if there was an error on any block, we mark all
353 * data blocks as being in error.
354 */
355 if (!data->error)
356 data->bytes_xfered = data->blocks * data->blksz;
357 else
358 data->bytes_xfered = 0;
359
360 pxamci_disable_irq(host, DATA_TRAN_DONE);
361
362 host->data = NULL;
363 if (host->mrq->stop) {
364 pxamci_stop_clock(host);
365 pxamci_start_cmd(host, host->mrq->stop, host->cmdat);
366 } else {
367 pxamci_finish_request(host, host->mrq);
368 }
369
370 return 1;
371 }
372
pxamci_irq(int irq,void * devid)373 static irqreturn_t pxamci_irq(int irq, void *devid)
374 {
375 struct pxamci_host *host = devid;
376 unsigned int ireg;
377 int handled = 0;
378
379 ireg = readl(host->base + MMC_I_REG) & ~readl(host->base + MMC_I_MASK);
380
381 if (ireg) {
382 unsigned stat = readl(host->base + MMC_STAT);
383
384 pr_debug("PXAMCI: irq %08x stat %08x\n", ireg, stat);
385
386 if (ireg & END_CMD_RES)
387 handled |= pxamci_cmd_done(host, stat);
388 if (ireg & DATA_TRAN_DONE)
389 handled |= pxamci_data_done(host, stat);
390 if (ireg & SDIO_INT) {
391 mmc_signal_sdio_irq(host->mmc);
392 handled = 1;
393 }
394 }
395
396 return IRQ_RETVAL(handled);
397 }
398
pxamci_request(struct mmc_host * mmc,struct mmc_request * mrq)399 static void pxamci_request(struct mmc_host *mmc, struct mmc_request *mrq)
400 {
401 struct pxamci_host *host = mmc_priv(mmc);
402 unsigned int cmdat;
403
404 WARN_ON(host->mrq != NULL);
405
406 host->mrq = mrq;
407
408 pxamci_stop_clock(host);
409
410 cmdat = host->cmdat;
411 host->cmdat &= ~CMDAT_INIT;
412
413 if (mrq->data) {
414 pxamci_setup_data(host, mrq->data);
415
416 cmdat &= ~CMDAT_BUSY;
417 cmdat |= CMDAT_DATAEN | CMDAT_DMAEN;
418 if (mrq->data->flags & MMC_DATA_WRITE)
419 cmdat |= CMDAT_WRITE;
420 }
421
422 pxamci_start_cmd(host, mrq->cmd, cmdat);
423 }
424
pxamci_get_ro(struct mmc_host * mmc)425 static int pxamci_get_ro(struct mmc_host *mmc)
426 {
427 struct pxamci_host *host = mmc_priv(mmc);
428
429 if (host->use_ro_gpio)
430 return mmc_gpio_get_ro(mmc);
431 if (host->pdata && host->pdata->get_ro)
432 return !!host->pdata->get_ro(mmc_dev(mmc));
433 /*
434 * Board doesn't support read only detection; let the mmc core
435 * decide what to do.
436 */
437 return -ENOSYS;
438 }
439
pxamci_set_ios(struct mmc_host * mmc,struct mmc_ios * ios)440 static void pxamci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
441 {
442 struct pxamci_host *host = mmc_priv(mmc);
443
444 if (ios->clock) {
445 unsigned long rate = host->clkrate;
446 unsigned int clk = rate / ios->clock;
447
448 if (host->clkrt == CLKRT_OFF)
449 clk_prepare_enable(host->clk);
450
451 if (ios->clock == 26000000) {
452 /* to support 26MHz */
453 host->clkrt = 7;
454 } else {
455 /* to handle (19.5MHz, 26MHz) */
456 if (!clk)
457 clk = 1;
458
459 /*
460 * clk might result in a lower divisor than we
461 * desire. check for that condition and adjust
462 * as appropriate.
463 */
464 if (rate / clk > ios->clock)
465 clk <<= 1;
466 host->clkrt = fls(clk) - 1;
467 }
468
469 /*
470 * we write clkrt on the next command
471 */
472 } else {
473 pxamci_stop_clock(host);
474 if (host->clkrt != CLKRT_OFF) {
475 host->clkrt = CLKRT_OFF;
476 clk_disable_unprepare(host->clk);
477 }
478 }
479
480 if (host->power_mode != ios->power_mode) {
481 int ret;
482
483 host->power_mode = ios->power_mode;
484
485 ret = pxamci_set_power(host, ios->power_mode, ios->vdd);
486 if (ret) {
487 dev_err(mmc_dev(mmc), "unable to set power\n");
488 /*
489 * The .set_ios() function in the mmc_host_ops
490 * struct return void, and failing to set the
491 * power should be rare so we print an error and
492 * return here.
493 */
494 return;
495 }
496
497 if (ios->power_mode == MMC_POWER_ON)
498 host->cmdat |= CMDAT_INIT;
499 }
500
501 if (ios->bus_width == MMC_BUS_WIDTH_4)
502 host->cmdat |= CMDAT_SD_4DAT;
503 else
504 host->cmdat &= ~CMDAT_SD_4DAT;
505
506 dev_dbg(mmc_dev(mmc), "PXAMCI: clkrt = %x cmdat = %x\n",
507 host->clkrt, host->cmdat);
508 }
509
pxamci_enable_sdio_irq(struct mmc_host * host,int enable)510 static void pxamci_enable_sdio_irq(struct mmc_host *host, int enable)
511 {
512 struct pxamci_host *pxa_host = mmc_priv(host);
513
514 if (enable)
515 pxamci_enable_irq(pxa_host, SDIO_INT);
516 else
517 pxamci_disable_irq(pxa_host, SDIO_INT);
518 }
519
520 static const struct mmc_host_ops pxamci_ops = {
521 .request = pxamci_request,
522 .get_cd = mmc_gpio_get_cd,
523 .get_ro = pxamci_get_ro,
524 .set_ios = pxamci_set_ios,
525 .enable_sdio_irq = pxamci_enable_sdio_irq,
526 };
527
pxamci_dma_irq(void * param)528 static void pxamci_dma_irq(void *param)
529 {
530 struct pxamci_host *host = param;
531 struct dma_tx_state state;
532 enum dma_status status;
533 struct dma_chan *chan;
534 unsigned long flags;
535
536 spin_lock_irqsave(&host->lock, flags);
537
538 if (!host->data)
539 goto out_unlock;
540
541 if (host->data->flags & MMC_DATA_READ)
542 chan = host->dma_chan_rx;
543 else
544 chan = host->dma_chan_tx;
545
546 status = dmaengine_tx_status(chan, host->dma_cookie, &state);
547
548 if (likely(status == DMA_COMPLETE)) {
549 writel(BUF_PART_FULL, host->base + MMC_PRTBUF);
550 } else {
551 pr_err("%s: DMA error on %s channel\n", mmc_hostname(host->mmc),
552 host->data->flags & MMC_DATA_READ ? "rx" : "tx");
553 host->data->error = -EIO;
554 pxamci_data_done(host, 0);
555 }
556
557 out_unlock:
558 spin_unlock_irqrestore(&host->lock, flags);
559 }
560
pxamci_detect_irq(int irq,void * devid)561 static irqreturn_t pxamci_detect_irq(int irq, void *devid)
562 {
563 struct pxamci_host *host = mmc_priv(devid);
564
565 mmc_detect_change(devid, msecs_to_jiffies(host->detect_delay_ms));
566 return IRQ_HANDLED;
567 }
568
569 #ifdef CONFIG_OF
570 static const struct of_device_id pxa_mmc_dt_ids[] = {
571 { .compatible = "marvell,pxa-mmc" },
572 { }
573 };
574
575 MODULE_DEVICE_TABLE(of, pxa_mmc_dt_ids);
576
pxamci_of_init(struct platform_device * pdev,struct mmc_host * mmc)577 static int pxamci_of_init(struct platform_device *pdev,
578 struct mmc_host *mmc)
579 {
580 struct device_node *np = pdev->dev.of_node;
581 struct pxamci_host *host = mmc_priv(mmc);
582 u32 tmp;
583 int ret;
584
585 if (!np)
586 return 0;
587
588 /* pxa-mmc specific */
589 if (of_property_read_u32(np, "pxa-mmc,detect-delay-ms", &tmp) == 0)
590 host->detect_delay_ms = tmp;
591
592 ret = mmc_of_parse(mmc);
593 if (ret < 0)
594 return ret;
595
596 return 0;
597 }
598 #else
pxamci_of_init(struct platform_device * pdev,struct mmc_host * mmc)599 static int pxamci_of_init(struct platform_device *pdev,
600 struct mmc_host *mmc)
601 {
602 return 0;
603 }
604 #endif
605
pxamci_probe(struct platform_device * pdev)606 static int pxamci_probe(struct platform_device *pdev)
607 {
608 struct mmc_host *mmc;
609 struct pxamci_host *host = NULL;
610 struct device *dev = &pdev->dev;
611 struct resource *r;
612 int ret, irq;
613
614 irq = platform_get_irq(pdev, 0);
615 if (irq < 0)
616 return irq;
617
618 mmc = mmc_alloc_host(sizeof(struct pxamci_host), dev);
619 if (!mmc) {
620 ret = -ENOMEM;
621 goto out;
622 }
623
624 mmc->ops = &pxamci_ops;
625
626 /*
627 * We can do SG-DMA, but we don't because we never know how much
628 * data we successfully wrote to the card.
629 */
630 mmc->max_segs = NR_SG;
631
632 /*
633 * Our hardware DMA can handle a maximum of one page per SG entry.
634 */
635 mmc->max_seg_size = PAGE_SIZE;
636
637 /*
638 * Block length register is only 10 bits before PXA27x.
639 */
640 mmc->max_blk_size = cpu_is_pxa25x() ? 1023 : 2048;
641
642 /*
643 * Block count register is 16 bits.
644 */
645 mmc->max_blk_count = 65535;
646
647 ret = pxamci_of_init(pdev, mmc);
648 if (ret)
649 goto out;
650
651 host = mmc_priv(mmc);
652 host->mmc = mmc;
653 host->pdata = pdev->dev.platform_data;
654 host->clkrt = CLKRT_OFF;
655
656 host->clk = devm_clk_get(dev, NULL);
657 if (IS_ERR(host->clk)) {
658 ret = PTR_ERR(host->clk);
659 host->clk = NULL;
660 goto out;
661 }
662
663 host->clkrate = clk_get_rate(host->clk);
664
665 /*
666 * Calculate minimum clock rate, rounding up.
667 */
668 mmc->f_min = (host->clkrate + 63) / 64;
669 mmc->f_max = (mmc_has_26MHz()) ? 26000000 : host->clkrate;
670
671 ret = pxamci_init_ocr(host);
672 if (ret < 0)
673 goto out;
674
675 mmc->caps = 0;
676 host->cmdat = 0;
677 if (!cpu_is_pxa25x()) {
678 mmc->caps |= MMC_CAP_4_BIT_DATA | MMC_CAP_SDIO_IRQ;
679 host->cmdat |= CMDAT_SDIO_INT_EN;
680 if (mmc_has_26MHz())
681 mmc->caps |= MMC_CAP_MMC_HIGHSPEED |
682 MMC_CAP_SD_HIGHSPEED;
683 }
684
685 spin_lock_init(&host->lock);
686 host->imask = MMC_I_MASK_ALL;
687
688 host->base = devm_platform_get_and_ioremap_resource(pdev, 0, &r);
689 if (IS_ERR(host->base)) {
690 ret = PTR_ERR(host->base);
691 goto out;
692 }
693 host->res = r;
694
695 /*
696 * Ensure that the host controller is shut down, and setup
697 * with our defaults.
698 */
699 pxamci_stop_clock(host);
700 writel(0, host->base + MMC_SPI);
701 writel(64, host->base + MMC_RESTO);
702 writel(host->imask, host->base + MMC_I_MASK);
703
704 ret = devm_request_irq(dev, irq, pxamci_irq, 0,
705 DRIVER_NAME, host);
706 if (ret)
707 goto out;
708
709 platform_set_drvdata(pdev, mmc);
710
711 host->dma_chan_rx = dma_request_chan(dev, "rx");
712 if (IS_ERR(host->dma_chan_rx)) {
713 dev_err(dev, "unable to request rx dma channel\n");
714 ret = PTR_ERR(host->dma_chan_rx);
715 host->dma_chan_rx = NULL;
716 goto out;
717 }
718
719 host->dma_chan_tx = dma_request_chan(dev, "tx");
720 if (IS_ERR(host->dma_chan_tx)) {
721 dev_err(dev, "unable to request tx dma channel\n");
722 ret = PTR_ERR(host->dma_chan_tx);
723 host->dma_chan_tx = NULL;
724 goto out;
725 }
726
727 if (host->pdata) {
728 host->detect_delay_ms = host->pdata->detect_delay_ms;
729
730 host->power = devm_gpiod_get_optional(dev, "power", GPIOD_OUT_LOW);
731 if (IS_ERR(host->power)) {
732 ret = PTR_ERR(host->power);
733 dev_err(dev, "Failed requesting gpio_power\n");
734 goto out;
735 }
736
737 /* FIXME: should we pass detection delay to debounce? */
738 ret = mmc_gpiod_request_cd(mmc, "cd", 0, false, 0);
739 if (ret && ret != -ENOENT) {
740 dev_err(dev, "Failed requesting gpio_cd\n");
741 goto out;
742 }
743
744 if (!host->pdata->gpio_card_ro_invert)
745 mmc->caps2 |= MMC_CAP2_RO_ACTIVE_HIGH;
746
747 ret = mmc_gpiod_request_ro(mmc, "wp", 0, 0);
748 if (ret && ret != -ENOENT) {
749 dev_err(dev, "Failed requesting gpio_ro\n");
750 goto out;
751 }
752 if (!ret)
753 host->use_ro_gpio = true;
754
755 if (host->pdata->init)
756 host->pdata->init(dev, pxamci_detect_irq, mmc);
757
758 if (host->power && host->pdata->setpower)
759 dev_warn(dev, "gpio_power and setpower() both defined\n");
760 if (host->use_ro_gpio && host->pdata->get_ro)
761 dev_warn(dev, "gpio_ro and get_ro() both defined\n");
762 }
763
764 ret = mmc_add_host(mmc);
765 if (ret) {
766 if (host->pdata && host->pdata->exit)
767 host->pdata->exit(dev, mmc);
768 goto out;
769 }
770
771 return 0;
772
773 out:
774 if (host) {
775 if (host->dma_chan_rx)
776 dma_release_channel(host->dma_chan_rx);
777 if (host->dma_chan_tx)
778 dma_release_channel(host->dma_chan_tx);
779 }
780 if (mmc)
781 mmc_free_host(mmc);
782 return ret;
783 }
784
pxamci_remove(struct platform_device * pdev)785 static void pxamci_remove(struct platform_device *pdev)
786 {
787 struct mmc_host *mmc = platform_get_drvdata(pdev);
788
789 if (mmc) {
790 struct pxamci_host *host = mmc_priv(mmc);
791
792 mmc_remove_host(mmc);
793
794 if (host->pdata && host->pdata->exit)
795 host->pdata->exit(&pdev->dev, mmc);
796
797 pxamci_stop_clock(host);
798 writel(TXFIFO_WR_REQ|RXFIFO_RD_REQ|CLK_IS_OFF|STOP_CMD|
799 END_CMD_RES|PRG_DONE|DATA_TRAN_DONE,
800 host->base + MMC_I_MASK);
801
802 dmaengine_terminate_all(host->dma_chan_rx);
803 dmaengine_terminate_all(host->dma_chan_tx);
804 dma_release_channel(host->dma_chan_rx);
805 dma_release_channel(host->dma_chan_tx);
806
807 mmc_free_host(mmc);
808 }
809 }
810
811 static struct platform_driver pxamci_driver = {
812 .probe = pxamci_probe,
813 .remove_new = pxamci_remove,
814 .driver = {
815 .name = DRIVER_NAME,
816 .probe_type = PROBE_PREFER_ASYNCHRONOUS,
817 .of_match_table = of_match_ptr(pxa_mmc_dt_ids),
818 },
819 };
820
821 module_platform_driver(pxamci_driver);
822
823 MODULE_DESCRIPTION("PXA Multimedia Card Interface Driver");
824 MODULE_LICENSE("GPL");
825 MODULE_ALIAS("platform:pxa2xx-mci");
826