1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * IMI RDACM21 GMSL Camera Driver
4 *
5 * Copyright (C) 2017-2020 Jacopo Mondi
6 * Copyright (C) 2017-2019 Kieran Bingham
7 * Copyright (C) 2017-2019 Laurent Pinchart
8 * Copyright (C) 2017-2019 Niklas Söderlund
9 * Copyright (C) 2016 Renesas Electronics Corporation
10 * Copyright (C) 2015 Cogent Embedded, Inc.
11 */
12
13 #include <linux/delay.h>
14 #include <linux/fwnode.h>
15 #include <linux/init.h>
16 #include <linux/i2c.h>
17 #include <linux/module.h>
18 #include <linux/slab.h>
19 #include <linux/videodev2.h>
20
21 #include <media/v4l2-async.h>
22 #include <media/v4l2-ctrls.h>
23 #include <media/v4l2-subdev.h>
24 #include "max9271.h"
25
26 #define MAX9271_RESET_CYCLES 10
27
28 #define OV490_I2C_ADDRESS 0x24
29
30 #define OV490_PAGE_HIGH_REG 0xfffd
31 #define OV490_PAGE_LOW_REG 0xfffe
32
33 /*
34 * The SCCB slave handling is undocumented; the registers naming scheme is
35 * totally arbitrary.
36 */
37 #define OV490_SCCB_SLAVE_WRITE 0x00
38 #define OV490_SCCB_SLAVE_READ 0x01
39 #define OV490_SCCB_SLAVE0_DIR 0x80195000
40 #define OV490_SCCB_SLAVE0_ADDR_HIGH 0x80195001
41 #define OV490_SCCB_SLAVE0_ADDR_LOW 0x80195002
42
43 #define OV490_DVP_CTRL3 0x80286009
44
45 #define OV490_ODS_CTRL_FRAME_OUTPUT_EN 0x0c
46 #define OV490_ODS_CTRL 0x8029d000
47
48 #define OV490_HOST_CMD 0x808000c0
49 #define OV490_HOST_CMD_TRIGGER 0xc1
50
51 #define OV490_ID_VAL 0x0490
52 #define OV490_ID(_p, _v) ((((_p) & 0xff) << 8) | ((_v) & 0xff))
53 #define OV490_PID 0x8080300a
54 #define OV490_VER 0x8080300b
55 #define OV490_PID_TIMEOUT 20
56 #define OV490_OUTPUT_EN_TIMEOUT 300
57
58 #define OV490_GPIO0 BIT(0)
59 #define OV490_SPWDN0 BIT(0)
60 #define OV490_GPIO_SEL0 0x80800050
61 #define OV490_GPIO_SEL1 0x80800051
62 #define OV490_GPIO_DIRECTION0 0x80800054
63 #define OV490_GPIO_DIRECTION1 0x80800055
64 #define OV490_GPIO_OUTPUT_VALUE0 0x80800058
65 #define OV490_GPIO_OUTPUT_VALUE1 0x80800059
66
67 #define OV490_ISP_HSIZE_LOW 0x80820060
68 #define OV490_ISP_HSIZE_HIGH 0x80820061
69 #define OV490_ISP_VSIZE_LOW 0x80820062
70 #define OV490_ISP_VSIZE_HIGH 0x80820063
71
72 #define OV10640_PID_TIMEOUT 20
73 #define OV10640_ID_HIGH 0xa6
74 #define OV10640_CHIP_ID 0x300a
75 #define OV10640_PIXEL_RATE 55000000
76
77 struct rdacm21_device {
78 struct device *dev;
79 struct max9271_device serializer;
80 struct i2c_client *isp;
81 struct v4l2_subdev sd;
82 struct media_pad pad;
83 struct v4l2_mbus_framefmt fmt;
84 struct v4l2_ctrl_handler ctrls;
85 u32 addrs[2];
86 u16 last_page;
87 };
88
sd_to_rdacm21(struct v4l2_subdev * sd)89 static inline struct rdacm21_device *sd_to_rdacm21(struct v4l2_subdev *sd)
90 {
91 return container_of(sd, struct rdacm21_device, sd);
92 }
93
94 static const struct ov490_reg {
95 u16 reg;
96 u8 val;
97 } ov490_regs_wizard[] = {
98 {0xfffd, 0x80},
99 {0xfffe, 0x82},
100 {0x0071, 0x11},
101 {0x0075, 0x11},
102 {0xfffe, 0x29},
103 {0x6010, 0x01},
104 /*
105 * OV490 EMB line disable in YUV and RAW data,
106 * NOTE: EMB line is still used in ISP and sensor
107 */
108 {0xe000, 0x14},
109 {0xfffe, 0x28},
110 {0x6000, 0x04},
111 {0x6004, 0x00},
112 /*
113 * PCLK polarity - useless due to silicon bug.
114 * Use 0x808000bb register instead.
115 */
116 {0x6008, 0x00},
117 {0xfffe, 0x80},
118 {0x0091, 0x00},
119 /* bit[3]=0 - PCLK polarity workaround. */
120 {0x00bb, 0x1d},
121 /* Ov490 FSIN: app_fsin_from_fsync */
122 {0xfffe, 0x85},
123 {0x0008, 0x00},
124 {0x0009, 0x01},
125 /* FSIN0 source. */
126 {0x000A, 0x05},
127 {0x000B, 0x00},
128 /* FSIN0 delay. */
129 {0x0030, 0x02},
130 {0x0031, 0x00},
131 {0x0032, 0x00},
132 {0x0033, 0x00},
133 /* FSIN1 delay. */
134 {0x0038, 0x02},
135 {0x0039, 0x00},
136 {0x003A, 0x00},
137 {0x003B, 0x00},
138 /* FSIN0 length. */
139 {0x0070, 0x2C},
140 {0x0071, 0x01},
141 {0x0072, 0x00},
142 {0x0073, 0x00},
143 /* FSIN1 length. */
144 {0x0074, 0x64},
145 {0x0075, 0x00},
146 {0x0076, 0x00},
147 {0x0077, 0x00},
148 {0x0000, 0x14},
149 {0x0001, 0x00},
150 {0x0002, 0x00},
151 {0x0003, 0x00},
152 /*
153 * Load fsin0,load fsin1,load other,
154 * It will be cleared automatically.
155 */
156 {0x0004, 0x32},
157 {0x0005, 0x00},
158 {0x0006, 0x00},
159 {0x0007, 0x00},
160 {0xfffe, 0x80},
161 /* Sensor FSIN. */
162 {0x0081, 0x00},
163 /* ov10640 FSIN enable */
164 {0xfffe, 0x19},
165 {0x5000, 0x00},
166 {0x5001, 0x30},
167 {0x5002, 0x8c},
168 {0x5003, 0xb2},
169 {0xfffe, 0x80},
170 {0x00c0, 0xc1},
171 /* ov10640 HFLIP=1 by default */
172 {0xfffe, 0x19},
173 {0x5000, 0x01},
174 {0x5001, 0x00},
175 {0xfffe, 0x80},
176 {0x00c0, 0xdc},
177 };
178
ov490_read(struct rdacm21_device * dev,u16 reg,u8 * val)179 static int ov490_read(struct rdacm21_device *dev, u16 reg, u8 *val)
180 {
181 u8 buf[2] = { reg >> 8, reg };
182 int ret;
183
184 ret = i2c_master_send(dev->isp, buf, 2);
185 if (ret == 2)
186 ret = i2c_master_recv(dev->isp, val, 1);
187
188 if (ret < 0) {
189 dev_dbg(dev->dev, "%s: register 0x%04x read failed (%d)\n",
190 __func__, reg, ret);
191 return ret;
192 }
193
194 return 0;
195 }
196
ov490_write(struct rdacm21_device * dev,u16 reg,u8 val)197 static int ov490_write(struct rdacm21_device *dev, u16 reg, u8 val)
198 {
199 u8 buf[3] = { reg >> 8, reg, val };
200 int ret;
201
202 ret = i2c_master_send(dev->isp, buf, 3);
203 if (ret < 0) {
204 dev_err(dev->dev, "%s: register 0x%04x write failed (%d)\n",
205 __func__, reg, ret);
206 return ret;
207 }
208
209 return 0;
210 }
211
ov490_set_page(struct rdacm21_device * dev,u16 page)212 static int ov490_set_page(struct rdacm21_device *dev, u16 page)
213 {
214 u8 page_high = page >> 8;
215 u8 page_low = page;
216 int ret;
217
218 if (page == dev->last_page)
219 return 0;
220
221 if (page_high != (dev->last_page >> 8)) {
222 ret = ov490_write(dev, OV490_PAGE_HIGH_REG, page_high);
223 if (ret)
224 return ret;
225 }
226
227 if (page_low != (u8)dev->last_page) {
228 ret = ov490_write(dev, OV490_PAGE_LOW_REG, page_low);
229 if (ret)
230 return ret;
231 }
232
233 dev->last_page = page;
234 usleep_range(100, 150);
235
236 return 0;
237 }
238
ov490_read_reg(struct rdacm21_device * dev,u32 reg,u8 * val)239 static int ov490_read_reg(struct rdacm21_device *dev, u32 reg, u8 *val)
240 {
241 int ret;
242
243 ret = ov490_set_page(dev, reg >> 16);
244 if (ret)
245 return ret;
246
247 ret = ov490_read(dev, (u16)reg, val);
248 if (ret)
249 return ret;
250
251 dev_dbg(dev->dev, "%s: 0x%08x = 0x%02x\n", __func__, reg, *val);
252
253 return 0;
254 }
255
ov490_write_reg(struct rdacm21_device * dev,u32 reg,u8 val)256 static int ov490_write_reg(struct rdacm21_device *dev, u32 reg, u8 val)
257 {
258 int ret;
259
260 ret = ov490_set_page(dev, reg >> 16);
261 if (ret)
262 return ret;
263
264 ret = ov490_write(dev, (u16)reg, val);
265 if (ret)
266 return ret;
267
268 dev_dbg(dev->dev, "%s: 0x%08x = 0x%02x\n", __func__, reg, val);
269
270 return 0;
271 }
272
rdacm21_s_stream(struct v4l2_subdev * sd,int enable)273 static int rdacm21_s_stream(struct v4l2_subdev *sd, int enable)
274 {
275 struct rdacm21_device *dev = sd_to_rdacm21(sd);
276
277 /*
278 * Enable serial link now that the ISP provides a valid pixel clock
279 * to start serializing video data on the GMSL link.
280 */
281 return max9271_set_serial_link(&dev->serializer, enable);
282 }
283
rdacm21_enum_mbus_code(struct v4l2_subdev * sd,struct v4l2_subdev_state * sd_state,struct v4l2_subdev_mbus_code_enum * code)284 static int rdacm21_enum_mbus_code(struct v4l2_subdev *sd,
285 struct v4l2_subdev_state *sd_state,
286 struct v4l2_subdev_mbus_code_enum *code)
287 {
288 if (code->pad || code->index > 0)
289 return -EINVAL;
290
291 code->code = MEDIA_BUS_FMT_YUYV8_1X16;
292
293 return 0;
294 }
295
rdacm21_get_fmt(struct v4l2_subdev * sd,struct v4l2_subdev_state * sd_state,struct v4l2_subdev_format * format)296 static int rdacm21_get_fmt(struct v4l2_subdev *sd,
297 struct v4l2_subdev_state *sd_state,
298 struct v4l2_subdev_format *format)
299 {
300 struct v4l2_mbus_framefmt *mf = &format->format;
301 struct rdacm21_device *dev = sd_to_rdacm21(sd);
302
303 if (format->pad)
304 return -EINVAL;
305
306 mf->width = dev->fmt.width;
307 mf->height = dev->fmt.height;
308 mf->code = MEDIA_BUS_FMT_YUYV8_1X16;
309 mf->colorspace = V4L2_COLORSPACE_SRGB;
310 mf->field = V4L2_FIELD_NONE;
311 mf->ycbcr_enc = V4L2_YCBCR_ENC_601;
312 mf->quantization = V4L2_QUANTIZATION_FULL_RANGE;
313 mf->xfer_func = V4L2_XFER_FUNC_NONE;
314
315 return 0;
316 }
317
318 static const struct v4l2_subdev_video_ops rdacm21_video_ops = {
319 .s_stream = rdacm21_s_stream,
320 };
321
322 static const struct v4l2_subdev_pad_ops rdacm21_subdev_pad_ops = {
323 .enum_mbus_code = rdacm21_enum_mbus_code,
324 .get_fmt = rdacm21_get_fmt,
325 .set_fmt = rdacm21_get_fmt,
326 };
327
328 static const struct v4l2_subdev_ops rdacm21_subdev_ops = {
329 .video = &rdacm21_video_ops,
330 .pad = &rdacm21_subdev_pad_ops,
331 };
332
ov10640_power_up(struct rdacm21_device * dev)333 static void ov10640_power_up(struct rdacm21_device *dev)
334 {
335 /* Enable GPIO0#0 (reset) and GPIO1#0 (pwdn) as output lines. */
336 ov490_write_reg(dev, OV490_GPIO_SEL0, OV490_GPIO0);
337 ov490_write_reg(dev, OV490_GPIO_SEL1, OV490_SPWDN0);
338 ov490_write_reg(dev, OV490_GPIO_DIRECTION0, OV490_GPIO0);
339 ov490_write_reg(dev, OV490_GPIO_DIRECTION1, OV490_SPWDN0);
340
341 /* Power up OV10640 and then reset it. */
342 ov490_write_reg(dev, OV490_GPIO_OUTPUT_VALUE1, OV490_SPWDN0);
343 usleep_range(1500, 3000);
344
345 ov490_write_reg(dev, OV490_GPIO_OUTPUT_VALUE0, 0x00);
346 usleep_range(1500, 3000);
347 ov490_write_reg(dev, OV490_GPIO_OUTPUT_VALUE0, OV490_GPIO0);
348 usleep_range(3000, 5000);
349 }
350
ov10640_check_id(struct rdacm21_device * dev)351 static int ov10640_check_id(struct rdacm21_device *dev)
352 {
353 unsigned int i;
354 u8 val = 0;
355
356 /* Read OV10640 ID to test communications. */
357 for (i = 0; i < OV10640_PID_TIMEOUT; ++i) {
358 ov490_write_reg(dev, OV490_SCCB_SLAVE0_DIR,
359 OV490_SCCB_SLAVE_READ);
360 ov490_write_reg(dev, OV490_SCCB_SLAVE0_ADDR_HIGH,
361 OV10640_CHIP_ID >> 8);
362 ov490_write_reg(dev, OV490_SCCB_SLAVE0_ADDR_LOW,
363 OV10640_CHIP_ID & 0xff);
364
365 /*
366 * Trigger SCCB slave transaction and give it some time
367 * to complete.
368 */
369 ov490_write_reg(dev, OV490_HOST_CMD, OV490_HOST_CMD_TRIGGER);
370 usleep_range(1000, 1500);
371
372 ov490_read_reg(dev, OV490_SCCB_SLAVE0_DIR, &val);
373 if (val == OV10640_ID_HIGH)
374 break;
375 usleep_range(1000, 1500);
376 }
377 if (i == OV10640_PID_TIMEOUT) {
378 dev_err(dev->dev, "OV10640 ID mismatch: (0x%02x)\n", val);
379 return -ENODEV;
380 }
381
382 dev_dbg(dev->dev, "OV10640 ID = 0x%2x\n", val);
383
384 return 0;
385 }
386
ov490_initialize(struct rdacm21_device * dev)387 static int ov490_initialize(struct rdacm21_device *dev)
388 {
389 u8 pid, ver, val;
390 unsigned int i;
391 int ret;
392
393 ov10640_power_up(dev);
394
395 /*
396 * Read OV490 Id to test communications. Give it up to 40msec to
397 * exit from reset.
398 */
399 for (i = 0; i < OV490_PID_TIMEOUT; ++i) {
400 ret = ov490_read_reg(dev, OV490_PID, &pid);
401 if (ret == 0)
402 break;
403 usleep_range(1000, 2000);
404 }
405 if (i == OV490_PID_TIMEOUT) {
406 dev_err(dev->dev, "OV490 PID read failed (%d)\n", ret);
407 return ret;
408 }
409
410 ret = ov490_read_reg(dev, OV490_VER, &ver);
411 if (ret < 0)
412 return ret;
413
414 if (OV490_ID(pid, ver) != OV490_ID_VAL) {
415 dev_err(dev->dev, "OV490 ID mismatch (0x%04x)\n",
416 OV490_ID(pid, ver));
417 return -ENODEV;
418 }
419
420 /* Wait for firmware boot by reading streamon status. */
421 for (i = 0; i < OV490_OUTPUT_EN_TIMEOUT; ++i) {
422 ov490_read_reg(dev, OV490_ODS_CTRL, &val);
423 if (val == OV490_ODS_CTRL_FRAME_OUTPUT_EN)
424 break;
425 usleep_range(1000, 2000);
426 }
427 if (i == OV490_OUTPUT_EN_TIMEOUT) {
428 dev_err(dev->dev, "Timeout waiting for firmware boot\n");
429 return -ENODEV;
430 }
431
432 ret = ov10640_check_id(dev);
433 if (ret)
434 return ret;
435
436 /* Program OV490 with register-value table. */
437 for (i = 0; i < ARRAY_SIZE(ov490_regs_wizard); ++i) {
438 ret = ov490_write(dev, ov490_regs_wizard[i].reg,
439 ov490_regs_wizard[i].val);
440 if (ret < 0) {
441 dev_err(dev->dev,
442 "%s: register %u (0x%04x) write failed (%d)\n",
443 __func__, i, ov490_regs_wizard[i].reg, ret);
444
445 return -EIO;
446 }
447
448 usleep_range(100, 150);
449 }
450
451 /*
452 * The ISP is programmed with the content of a serial flash memory.
453 * Read the firmware configuration to reflect it through the V4L2 APIs.
454 */
455 ov490_read_reg(dev, OV490_ISP_HSIZE_HIGH, &val);
456 dev->fmt.width = (val & 0xf) << 8;
457 ov490_read_reg(dev, OV490_ISP_HSIZE_LOW, &val);
458 dev->fmt.width |= (val & 0xff);
459
460 ov490_read_reg(dev, OV490_ISP_VSIZE_HIGH, &val);
461 dev->fmt.height = (val & 0xf) << 8;
462 ov490_read_reg(dev, OV490_ISP_VSIZE_LOW, &val);
463 dev->fmt.height |= val & 0xff;
464
465 /* Set bus width to 12 bits with [0:11] ordering. */
466 ov490_write_reg(dev, OV490_DVP_CTRL3, 0x10);
467
468 dev_info(dev->dev, "Identified RDACM21 camera module\n");
469
470 return 0;
471 }
472
rdacm21_initialize(struct rdacm21_device * dev)473 static int rdacm21_initialize(struct rdacm21_device *dev)
474 {
475 int ret;
476
477 max9271_wake_up(&dev->serializer);
478
479 /* Enable reverse channel and disable the serial link. */
480 ret = max9271_set_serial_link(&dev->serializer, false);
481 if (ret)
482 return ret;
483
484 /* Configure I2C bus at 105Kbps speed and configure GMSL. */
485 ret = max9271_configure_i2c(&dev->serializer,
486 MAX9271_I2CSLVSH_469NS_234NS |
487 MAX9271_I2CSLVTO_1024US |
488 MAX9271_I2CMSTBT_105KBPS);
489 if (ret)
490 return ret;
491
492 ret = max9271_verify_id(&dev->serializer);
493 if (ret)
494 return ret;
495
496 /*
497 * Enable GPIO1 and hold OV490 in reset during max9271 configuration.
498 * The reset signal has to be asserted for at least 250 useconds.
499 */
500 ret = max9271_enable_gpios(&dev->serializer, MAX9271_GPIO1OUT);
501 if (ret)
502 return ret;
503
504 ret = max9271_clear_gpios(&dev->serializer, MAX9271_GPIO1OUT);
505 if (ret)
506 return ret;
507 usleep_range(250, 500);
508
509 ret = max9271_configure_gmsl_link(&dev->serializer);
510 if (ret)
511 return ret;
512
513 ret = max9271_set_address(&dev->serializer, dev->addrs[0]);
514 if (ret)
515 return ret;
516 dev->serializer.client->addr = dev->addrs[0];
517
518 ret = max9271_set_translation(&dev->serializer, dev->addrs[1],
519 OV490_I2C_ADDRESS);
520 if (ret)
521 return ret;
522 dev->isp->addr = dev->addrs[1];
523
524 /* Release OV490 from reset and initialize it. */
525 ret = max9271_set_gpios(&dev->serializer, MAX9271_GPIO1OUT);
526 if (ret)
527 return ret;
528 usleep_range(3000, 5000);
529
530 ret = ov490_initialize(dev);
531 if (ret)
532 return ret;
533
534 /*
535 * Set reverse channel high threshold to increase noise immunity.
536 *
537 * This should be compensated by increasing the reverse channel
538 * amplitude on the remote deserializer side.
539 */
540 return max9271_set_high_threshold(&dev->serializer, true);
541 }
542
rdacm21_probe(struct i2c_client * client)543 static int rdacm21_probe(struct i2c_client *client)
544 {
545 struct rdacm21_device *dev;
546 int ret;
547
548 dev = devm_kzalloc(&client->dev, sizeof(*dev), GFP_KERNEL);
549 if (!dev)
550 return -ENOMEM;
551 dev->dev = &client->dev;
552 dev->serializer.client = client;
553
554 ret = of_property_read_u32_array(client->dev.of_node, "reg",
555 dev->addrs, 2);
556 if (ret < 0) {
557 dev_err(dev->dev, "Invalid DT reg property: %d\n", ret);
558 return -EINVAL;
559 }
560
561 /* Create the dummy I2C client for the sensor. */
562 dev->isp = i2c_new_dummy_device(client->adapter, OV490_I2C_ADDRESS);
563 if (IS_ERR(dev->isp))
564 return PTR_ERR(dev->isp);
565
566 ret = rdacm21_initialize(dev);
567 if (ret < 0)
568 goto error;
569
570 /* Initialize and register the subdevice. */
571 v4l2_i2c_subdev_init(&dev->sd, client, &rdacm21_subdev_ops);
572 dev->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
573
574 v4l2_ctrl_handler_init(&dev->ctrls, 1);
575 v4l2_ctrl_new_std(&dev->ctrls, NULL, V4L2_CID_PIXEL_RATE,
576 OV10640_PIXEL_RATE, OV10640_PIXEL_RATE, 1,
577 OV10640_PIXEL_RATE);
578 dev->sd.ctrl_handler = &dev->ctrls;
579
580 ret = dev->ctrls.error;
581 if (ret)
582 goto error_free_ctrls;
583
584 dev->pad.flags = MEDIA_PAD_FL_SOURCE;
585 dev->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
586 ret = media_entity_pads_init(&dev->sd.entity, 1, &dev->pad);
587 if (ret < 0)
588 goto error_free_ctrls;
589
590 ret = v4l2_async_register_subdev(&dev->sd);
591 if (ret)
592 goto error_free_ctrls;
593
594 return 0;
595
596 error_free_ctrls:
597 v4l2_ctrl_handler_free(&dev->ctrls);
598 error:
599 i2c_unregister_device(dev->isp);
600
601 return ret;
602 }
603
rdacm21_remove(struct i2c_client * client)604 static void rdacm21_remove(struct i2c_client *client)
605 {
606 struct rdacm21_device *dev = sd_to_rdacm21(i2c_get_clientdata(client));
607
608 v4l2_async_unregister_subdev(&dev->sd);
609 v4l2_ctrl_handler_free(&dev->ctrls);
610 i2c_unregister_device(dev->isp);
611 }
612
613 static const struct of_device_id rdacm21_of_ids[] = {
614 { .compatible = "imi,rdacm21" },
615 { }
616 };
617 MODULE_DEVICE_TABLE(of, rdacm21_of_ids);
618
619 static struct i2c_driver rdacm21_i2c_driver = {
620 .driver = {
621 .name = "rdacm21",
622 .of_match_table = rdacm21_of_ids,
623 },
624 .probe = rdacm21_probe,
625 .remove = rdacm21_remove,
626 };
627
628 module_i2c_driver(rdacm21_i2c_driver);
629
630 MODULE_DESCRIPTION("GMSL Camera driver for RDACM21");
631 MODULE_AUTHOR("Jacopo Mondi");
632 MODULE_LICENSE("GPL v2");
633