1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * ispcsiphy.c
4 *
5 * TI OMAP3 ISP - CSI PHY module
6 *
7 * Copyright (C) 2010 Nokia Corporation
8 * Copyright (C) 2009 Texas Instruments, Inc.
9 *
10 * Contacts: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
11 * Sakari Ailus <sakari.ailus@iki.fi>
12 */
13
14 #include <linux/delay.h>
15 #include <linux/device.h>
16 #include <linux/regmap.h>
17 #include <linux/regulator/consumer.h>
18
19 #include "isp.h"
20 #include "ispreg.h"
21 #include "ispcsiphy.h"
22
csiphy_routing_cfg_3630(struct isp_csiphy * phy,enum isp_interface_type iface,bool ccp2_strobe)23 static void csiphy_routing_cfg_3630(struct isp_csiphy *phy,
24 enum isp_interface_type iface,
25 bool ccp2_strobe)
26 {
27 u32 reg;
28 u32 shift, mode;
29
30 regmap_read(phy->isp->syscon, phy->isp->syscon_offset, ®);
31
32 switch (iface) {
33 default:
34 /* Should not happen in practice, but let's keep the compiler happy. */
35 return;
36 case ISP_INTERFACE_CCP2B_PHY1:
37 reg &= ~OMAP3630_CONTROL_CAMERA_PHY_CTRL_CSI1_RX_SEL_PHY2;
38 shift = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_PHY1_SHIFT;
39 break;
40 case ISP_INTERFACE_CSI2C_PHY1:
41 shift = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_PHY1_SHIFT;
42 mode = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_DPHY;
43 break;
44 case ISP_INTERFACE_CCP2B_PHY2:
45 reg |= OMAP3630_CONTROL_CAMERA_PHY_CTRL_CSI1_RX_SEL_PHY2;
46 shift = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_PHY2_SHIFT;
47 break;
48 case ISP_INTERFACE_CSI2A_PHY2:
49 shift = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_PHY2_SHIFT;
50 mode = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_DPHY;
51 break;
52 }
53
54 /* Select data/clock or data/strobe mode for CCP2 */
55 if (iface == ISP_INTERFACE_CCP2B_PHY1 ||
56 iface == ISP_INTERFACE_CCP2B_PHY2) {
57 if (ccp2_strobe)
58 mode = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_CCP2_DATA_STROBE;
59 else
60 mode = OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_CCP2_DATA_CLOCK;
61 }
62
63 reg &= ~(OMAP3630_CONTROL_CAMERA_PHY_CTRL_CAMMODE_MASK << shift);
64 reg |= mode << shift;
65
66 regmap_write(phy->isp->syscon, phy->isp->syscon_offset, reg);
67 }
68
csiphy_routing_cfg_3430(struct isp_csiphy * phy,u32 iface,bool on,bool ccp2_strobe)69 static void csiphy_routing_cfg_3430(struct isp_csiphy *phy, u32 iface, bool on,
70 bool ccp2_strobe)
71 {
72 u32 csirxfe = OMAP343X_CONTROL_CSIRXFE_PWRDNZ
73 | OMAP343X_CONTROL_CSIRXFE_RESET;
74
75 /* Only the CCP2B on PHY1 is configurable. */
76 if (iface != ISP_INTERFACE_CCP2B_PHY1)
77 return;
78
79 if (!on) {
80 regmap_write(phy->isp->syscon, phy->isp->syscon_offset, 0);
81 return;
82 }
83
84 if (ccp2_strobe)
85 csirxfe |= OMAP343X_CONTROL_CSIRXFE_SELFORM;
86
87 regmap_write(phy->isp->syscon, phy->isp->syscon_offset, csirxfe);
88 }
89
90 /*
91 * Configure OMAP 3 CSI PHY routing.
92 * @phy: relevant phy device
93 * @iface: ISP_INTERFACE_*
94 * @on: power on or off
95 * @ccp2_strobe: false: data/clock, true: data/strobe
96 *
97 * Note that the underlying routing configuration registers are part of the
98 * control (SCM) register space and part of the CORE power domain on both 3430
99 * and 3630, so they will not hold their contents in off-mode. This isn't an
100 * issue since the MPU power domain is forced on whilst the ISP is in use.
101 */
csiphy_routing_cfg(struct isp_csiphy * phy,enum isp_interface_type iface,bool on,bool ccp2_strobe)102 static void csiphy_routing_cfg(struct isp_csiphy *phy,
103 enum isp_interface_type iface, bool on,
104 bool ccp2_strobe)
105 {
106 if (phy->isp->phy_type == ISP_PHY_TYPE_3630 && on)
107 return csiphy_routing_cfg_3630(phy, iface, ccp2_strobe);
108 if (phy->isp->phy_type == ISP_PHY_TYPE_3430)
109 return csiphy_routing_cfg_3430(phy, iface, on, ccp2_strobe);
110 }
111
112 /*
113 * csiphy_power_autoswitch_enable
114 * @enable: Sets or clears the autoswitch function enable flag.
115 */
csiphy_power_autoswitch_enable(struct isp_csiphy * phy,bool enable)116 static void csiphy_power_autoswitch_enable(struct isp_csiphy *phy, bool enable)
117 {
118 isp_reg_clr_set(phy->isp, phy->cfg_regs, ISPCSI2_PHY_CFG,
119 ISPCSI2_PHY_CFG_PWR_AUTO,
120 enable ? ISPCSI2_PHY_CFG_PWR_AUTO : 0);
121 }
122
123 /*
124 * csiphy_set_power
125 * @power: Power state to be set.
126 *
127 * Returns 0 if successful, or -EBUSY if the retry count is exceeded.
128 */
csiphy_set_power(struct isp_csiphy * phy,u32 power)129 static int csiphy_set_power(struct isp_csiphy *phy, u32 power)
130 {
131 u32 reg;
132 u8 retry_count;
133
134 isp_reg_clr_set(phy->isp, phy->cfg_regs, ISPCSI2_PHY_CFG,
135 ISPCSI2_PHY_CFG_PWR_CMD_MASK, power);
136
137 retry_count = 0;
138 do {
139 udelay(50);
140 reg = isp_reg_readl(phy->isp, phy->cfg_regs, ISPCSI2_PHY_CFG) &
141 ISPCSI2_PHY_CFG_PWR_STATUS_MASK;
142
143 if (reg != power >> 2)
144 retry_count++;
145
146 } while ((reg != power >> 2) && (retry_count < 100));
147
148 if (retry_count == 100) {
149 dev_err(phy->isp->dev, "CSI2 CIO set power failed!\n");
150 return -EBUSY;
151 }
152
153 return 0;
154 }
155
156 /*
157 * TCLK values are OK at their reset values
158 */
159 #define TCLK_TERM 0
160 #define TCLK_MISS 1
161 #define TCLK_SETTLE 14
162
omap3isp_csiphy_config(struct isp_csiphy * phy)163 static int omap3isp_csiphy_config(struct isp_csiphy *phy)
164 {
165 struct isp_pipeline *pipe = to_isp_pipeline(phy->entity);
166 struct isp_bus_cfg *buscfg;
167 struct isp_csiphy_lanes_cfg *lanes;
168 int csi2_ddrclk_khz;
169 unsigned int num_data_lanes, used_lanes = 0;
170 unsigned int i;
171 u32 reg;
172
173 buscfg = v4l2_subdev_to_bus_cfg(pipe->external);
174 if (WARN_ON(!buscfg))
175 return -EPIPE;
176
177 if (buscfg->interface == ISP_INTERFACE_CCP2B_PHY1
178 || buscfg->interface == ISP_INTERFACE_CCP2B_PHY2) {
179 lanes = &buscfg->bus.ccp2.lanecfg;
180 num_data_lanes = 1;
181 } else {
182 lanes = &buscfg->bus.csi2.lanecfg;
183 num_data_lanes = buscfg->bus.csi2.num_data_lanes;
184 }
185
186 if (num_data_lanes > phy->num_data_lanes)
187 return -EINVAL;
188
189 /* Clock and data lanes verification */
190 for (i = 0; i < num_data_lanes; i++) {
191 if (lanes->data[i].pol > 1 || lanes->data[i].pos > 3)
192 return -EINVAL;
193
194 if (used_lanes & (1 << lanes->data[i].pos))
195 return -EINVAL;
196
197 used_lanes |= 1 << lanes->data[i].pos;
198 }
199
200 if (lanes->clk.pol > 1 || lanes->clk.pos > 3)
201 return -EINVAL;
202
203 if (lanes->clk.pos == 0 || used_lanes & (1 << lanes->clk.pos))
204 return -EINVAL;
205
206 /*
207 * The PHY configuration is lost in off mode, that's not an
208 * issue since the MPU power domain is forced on whilst the
209 * ISP is in use.
210 */
211 csiphy_routing_cfg(phy, buscfg->interface, true,
212 buscfg->bus.ccp2.phy_layer);
213
214 /* DPHY timing configuration */
215 /* CSI-2 is DDR and we only count used lanes. */
216 csi2_ddrclk_khz = pipe->external_rate / 1000
217 / (2 * hweight32(used_lanes)) * pipe->external_width;
218
219 reg = isp_reg_readl(phy->isp, phy->phy_regs, ISPCSIPHY_REG0);
220
221 reg &= ~(ISPCSIPHY_REG0_THS_TERM_MASK |
222 ISPCSIPHY_REG0_THS_SETTLE_MASK);
223 /* THS_TERM: Programmed value = ceil(12.5 ns/DDRClk period) - 1. */
224 reg |= (DIV_ROUND_UP(25 * csi2_ddrclk_khz, 2000000) - 1)
225 << ISPCSIPHY_REG0_THS_TERM_SHIFT;
226 /* THS_SETTLE: Programmed value = ceil(90 ns/DDRClk period) + 3. */
227 reg |= (DIV_ROUND_UP(90 * csi2_ddrclk_khz, 1000000) + 3)
228 << ISPCSIPHY_REG0_THS_SETTLE_SHIFT;
229
230 isp_reg_writel(phy->isp, reg, phy->phy_regs, ISPCSIPHY_REG0);
231
232 reg = isp_reg_readl(phy->isp, phy->phy_regs, ISPCSIPHY_REG1);
233
234 reg &= ~(ISPCSIPHY_REG1_TCLK_TERM_MASK |
235 ISPCSIPHY_REG1_TCLK_MISS_MASK |
236 ISPCSIPHY_REG1_TCLK_SETTLE_MASK);
237 reg |= TCLK_TERM << ISPCSIPHY_REG1_TCLK_TERM_SHIFT;
238 reg |= TCLK_MISS << ISPCSIPHY_REG1_TCLK_MISS_SHIFT;
239 reg |= TCLK_SETTLE << ISPCSIPHY_REG1_TCLK_SETTLE_SHIFT;
240
241 isp_reg_writel(phy->isp, reg, phy->phy_regs, ISPCSIPHY_REG1);
242
243 /* DPHY lane configuration */
244 reg = isp_reg_readl(phy->isp, phy->cfg_regs, ISPCSI2_PHY_CFG);
245
246 for (i = 0; i < num_data_lanes; i++) {
247 reg &= ~(ISPCSI2_PHY_CFG_DATA_POL_MASK(i + 1) |
248 ISPCSI2_PHY_CFG_DATA_POSITION_MASK(i + 1));
249 reg |= (lanes->data[i].pol <<
250 ISPCSI2_PHY_CFG_DATA_POL_SHIFT(i + 1));
251 reg |= (lanes->data[i].pos <<
252 ISPCSI2_PHY_CFG_DATA_POSITION_SHIFT(i + 1));
253 }
254
255 reg &= ~(ISPCSI2_PHY_CFG_CLOCK_POL_MASK |
256 ISPCSI2_PHY_CFG_CLOCK_POSITION_MASK);
257 reg |= lanes->clk.pol << ISPCSI2_PHY_CFG_CLOCK_POL_SHIFT;
258 reg |= lanes->clk.pos << ISPCSI2_PHY_CFG_CLOCK_POSITION_SHIFT;
259
260 isp_reg_writel(phy->isp, reg, phy->cfg_regs, ISPCSI2_PHY_CFG);
261
262 return 0;
263 }
264
omap3isp_csiphy_acquire(struct isp_csiphy * phy,struct media_entity * entity)265 int omap3isp_csiphy_acquire(struct isp_csiphy *phy, struct media_entity *entity)
266 {
267 int rval;
268
269 if (phy->vdd == NULL) {
270 dev_err(phy->isp->dev,
271 "Power regulator for CSI PHY not available\n");
272 return -ENODEV;
273 }
274
275 mutex_lock(&phy->mutex);
276
277 rval = regulator_enable(phy->vdd);
278 if (rval < 0)
279 goto done;
280
281 rval = omap3isp_csi2_reset(phy->csi2);
282 if (rval < 0)
283 goto done;
284
285 phy->entity = entity;
286
287 rval = omap3isp_csiphy_config(phy);
288 if (rval < 0)
289 goto done;
290
291 if (phy->isp->revision == ISP_REVISION_15_0) {
292 rval = csiphy_set_power(phy, ISPCSI2_PHY_CFG_PWR_CMD_ON);
293 if (rval) {
294 regulator_disable(phy->vdd);
295 goto done;
296 }
297
298 csiphy_power_autoswitch_enable(phy, true);
299 }
300 done:
301 if (rval < 0)
302 phy->entity = NULL;
303
304 mutex_unlock(&phy->mutex);
305 return rval;
306 }
307
omap3isp_csiphy_release(struct isp_csiphy * phy)308 void omap3isp_csiphy_release(struct isp_csiphy *phy)
309 {
310 mutex_lock(&phy->mutex);
311 if (phy->entity) {
312 struct isp_pipeline *pipe = to_isp_pipeline(phy->entity);
313 struct isp_bus_cfg *buscfg;
314
315 buscfg = v4l2_subdev_to_bus_cfg(pipe->external);
316 if (WARN_ON(!buscfg)) {
317 mutex_unlock(&phy->mutex);
318 return;
319 }
320
321 csiphy_routing_cfg(phy, buscfg->interface, false,
322 buscfg->bus.ccp2.phy_layer);
323 if (phy->isp->revision == ISP_REVISION_15_0) {
324 csiphy_power_autoswitch_enable(phy, false);
325 csiphy_set_power(phy, ISPCSI2_PHY_CFG_PWR_CMD_OFF);
326 }
327 regulator_disable(phy->vdd);
328 phy->entity = NULL;
329 }
330 mutex_unlock(&phy->mutex);
331 }
332
333 /*
334 * omap3isp_csiphy_init - Initialize the CSI PHY frontends
335 */
omap3isp_csiphy_init(struct isp_device * isp)336 int omap3isp_csiphy_init(struct isp_device *isp)
337 {
338 struct isp_csiphy *phy1 = &isp->isp_csiphy1;
339 struct isp_csiphy *phy2 = &isp->isp_csiphy2;
340
341 phy2->isp = isp;
342 phy2->csi2 = &isp->isp_csi2a;
343 phy2->num_data_lanes = ISP_CSIPHY2_NUM_DATA_LANES;
344 phy2->cfg_regs = OMAP3_ISP_IOMEM_CSI2A_REGS1;
345 phy2->phy_regs = OMAP3_ISP_IOMEM_CSIPHY2;
346 mutex_init(&phy2->mutex);
347
348 phy1->isp = isp;
349 mutex_init(&phy1->mutex);
350
351 if (isp->revision == ISP_REVISION_15_0) {
352 phy1->csi2 = &isp->isp_csi2c;
353 phy1->num_data_lanes = ISP_CSIPHY1_NUM_DATA_LANES;
354 phy1->cfg_regs = OMAP3_ISP_IOMEM_CSI2C_REGS1;
355 phy1->phy_regs = OMAP3_ISP_IOMEM_CSIPHY1;
356 }
357
358 return 0;
359 }
360
omap3isp_csiphy_cleanup(struct isp_device * isp)361 void omap3isp_csiphy_cleanup(struct isp_device *isp)
362 {
363 mutex_destroy(&isp->isp_csiphy1.mutex);
364 mutex_destroy(&isp->isp_csiphy2.mutex);
365 }
366