1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * Driver for Microchip 10BASE-T1S PHYs
4 *
5 * Support: Microchip Phys:
6 * lan8670/1/2 Rev.B1
7 * lan8650/1 Rev.B0 Internal PHYs
8 */
9
10 #include <linux/kernel.h>
11 #include <linux/module.h>
12 #include <linux/phy.h>
13
14 #define PHY_ID_LAN867X_REVB1 0x0007C162
15 #define PHY_ID_LAN865X_REVB0 0x0007C1B3
16
17 #define LAN867X_REG_STS2 0x0019
18
19 #define LAN867x_RESET_COMPLETE_STS BIT(11)
20
21 #define LAN865X_REG_CFGPARAM_ADDR 0x00D8
22 #define LAN865X_REG_CFGPARAM_DATA 0x00D9
23 #define LAN865X_REG_CFGPARAM_CTRL 0x00DA
24 #define LAN865X_REG_STS2 0x0019
25
26 #define LAN865X_CFGPARAM_READ_ENABLE BIT(1)
27
28 /* The arrays below are pulled from the following table from AN1699
29 * Access MMD Address Value Mask
30 * RMW 0x1F 0x00D0 0x0002 0x0E03
31 * RMW 0x1F 0x00D1 0x0000 0x0300
32 * RMW 0x1F 0x0084 0x3380 0xFFC0
33 * RMW 0x1F 0x0085 0x0006 0x000F
34 * RMW 0x1F 0x008A 0xC000 0xF800
35 * RMW 0x1F 0x0087 0x801C 0x801C
36 * RMW 0x1F 0x0088 0x033F 0x1FFF
37 * W 0x1F 0x008B 0x0404 ------
38 * RMW 0x1F 0x0080 0x0600 0x0600
39 * RMW 0x1F 0x00F1 0x2400 0x7F00
40 * RMW 0x1F 0x0096 0x2000 0x2000
41 * W 0x1F 0x0099 0x7F80 ------
42 */
43
44 static const u32 lan867x_revb1_fixup_registers[12] = {
45 0x00D0, 0x00D1, 0x0084, 0x0085,
46 0x008A, 0x0087, 0x0088, 0x008B,
47 0x0080, 0x00F1, 0x0096, 0x0099,
48 };
49
50 static const u16 lan867x_revb1_fixup_values[12] = {
51 0x0002, 0x0000, 0x3380, 0x0006,
52 0xC000, 0x801C, 0x033F, 0x0404,
53 0x0600, 0x2400, 0x2000, 0x7F80,
54 };
55
56 static const u16 lan867x_revb1_fixup_masks[12] = {
57 0x0E03, 0x0300, 0xFFC0, 0x000F,
58 0xF800, 0x801C, 0x1FFF, 0xFFFF,
59 0x0600, 0x7F00, 0x2000, 0xFFFF,
60 };
61
62 /* LAN865x Rev.B0 configuration parameters from AN1760 */
63 static const u32 lan865x_revb0_fixup_registers[28] = {
64 0x0091, 0x0081, 0x0043, 0x0044,
65 0x0045, 0x0053, 0x0054, 0x0055,
66 0x0040, 0x0050, 0x00D0, 0x00E9,
67 0x00F5, 0x00F4, 0x00F8, 0x00F9,
68 0x00B0, 0x00B1, 0x00B2, 0x00B3,
69 0x00B4, 0x00B5, 0x00B6, 0x00B7,
70 0x00B8, 0x00B9, 0x00BA, 0x00BB,
71 };
72
73 static const u16 lan865x_revb0_fixup_values[28] = {
74 0x9660, 0x00C0, 0x00FF, 0xFFFF,
75 0x0000, 0x00FF, 0xFFFF, 0x0000,
76 0x0002, 0x0002, 0x5F21, 0x9E50,
77 0x1CF8, 0xC020, 0x9B00, 0x4E53,
78 0x0103, 0x0910, 0x1D26, 0x002A,
79 0x0103, 0x070D, 0x1720, 0x0027,
80 0x0509, 0x0E13, 0x1C25, 0x002B,
81 };
82
83 static const u16 lan865x_revb0_fixup_cfg_regs[5] = {
84 0x0084, 0x008A, 0x00AD, 0x00AE, 0x00AF
85 };
86
87 /* Pulled from AN1760 describing 'indirect read'
88 *
89 * write_register(0x4, 0x00D8, addr)
90 * write_register(0x4, 0x00DA, 0x2)
91 * return (int8)(read_register(0x4, 0x00D9))
92 *
93 * 0x4 refers to memory map selector 4, which maps to MDIO_MMD_VEND2
94 */
lan865x_revb0_indirect_read(struct phy_device * phydev,u16 addr)95 static int lan865x_revb0_indirect_read(struct phy_device *phydev, u16 addr)
96 {
97 int ret;
98
99 ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, LAN865X_REG_CFGPARAM_ADDR,
100 addr);
101 if (ret)
102 return ret;
103
104 ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, LAN865X_REG_CFGPARAM_CTRL,
105 LAN865X_CFGPARAM_READ_ENABLE);
106 if (ret)
107 return ret;
108
109 return phy_read_mmd(phydev, MDIO_MMD_VEND2, LAN865X_REG_CFGPARAM_DATA);
110 }
111
112 /* This is pulled straight from AN1760 from 'calculation of offset 1' &
113 * 'calculation of offset 2'
114 */
lan865x_generate_cfg_offsets(struct phy_device * phydev,s8 offsets[2])115 static int lan865x_generate_cfg_offsets(struct phy_device *phydev, s8 offsets[2])
116 {
117 const u16 fixup_regs[2] = {0x0004, 0x0008};
118 int ret;
119
120 for (int i = 0; i < ARRAY_SIZE(fixup_regs); i++) {
121 ret = lan865x_revb0_indirect_read(phydev, fixup_regs[i]);
122 if (ret < 0)
123 return ret;
124 if (ret & BIT(4))
125 offsets[i] = ret | 0xE0;
126 else
127 offsets[i] = ret;
128 }
129
130 return 0;
131 }
132
lan865x_read_cfg_params(struct phy_device * phydev,u16 cfg_params[])133 static int lan865x_read_cfg_params(struct phy_device *phydev, u16 cfg_params[])
134 {
135 int ret;
136
137 for (int i = 0; i < ARRAY_SIZE(lan865x_revb0_fixup_cfg_regs); i++) {
138 ret = phy_read_mmd(phydev, MDIO_MMD_VEND2,
139 lan865x_revb0_fixup_cfg_regs[i]);
140 if (ret < 0)
141 return ret;
142 cfg_params[i] = (u16)ret;
143 }
144
145 return 0;
146 }
147
lan865x_write_cfg_params(struct phy_device * phydev,u16 cfg_params[])148 static int lan865x_write_cfg_params(struct phy_device *phydev, u16 cfg_params[])
149 {
150 int ret;
151
152 for (int i = 0; i < ARRAY_SIZE(lan865x_revb0_fixup_cfg_regs); i++) {
153 ret = phy_write_mmd(phydev, MDIO_MMD_VEND2,
154 lan865x_revb0_fixup_cfg_regs[i],
155 cfg_params[i]);
156 if (ret)
157 return ret;
158 }
159
160 return 0;
161 }
162
lan865x_setup_cfgparam(struct phy_device * phydev)163 static int lan865x_setup_cfgparam(struct phy_device *phydev)
164 {
165 u16 cfg_params[ARRAY_SIZE(lan865x_revb0_fixup_cfg_regs)];
166 u16 cfg_results[5];
167 s8 offsets[2];
168 int ret;
169
170 ret = lan865x_generate_cfg_offsets(phydev, offsets);
171 if (ret)
172 return ret;
173
174 ret = lan865x_read_cfg_params(phydev, cfg_params);
175 if (ret)
176 return ret;
177
178 cfg_results[0] = (cfg_params[0] & 0x000F) |
179 FIELD_PREP(GENMASK(15, 10), 9 + offsets[0]) |
180 FIELD_PREP(GENMASK(15, 4), 14 + offsets[0]);
181 cfg_results[1] = (cfg_params[1] & 0x03FF) |
182 FIELD_PREP(GENMASK(15, 10), 40 + offsets[1]);
183 cfg_results[2] = (cfg_params[2] & 0xC0C0) |
184 FIELD_PREP(GENMASK(15, 8), 5 + offsets[0]) |
185 (9 + offsets[0]);
186 cfg_results[3] = (cfg_params[3] & 0xC0C0) |
187 FIELD_PREP(GENMASK(15, 8), 9 + offsets[0]) |
188 (14 + offsets[0]);
189 cfg_results[4] = (cfg_params[4] & 0xC0C0) |
190 FIELD_PREP(GENMASK(15, 8), 17 + offsets[0]) |
191 (22 + offsets[0]);
192
193 return lan865x_write_cfg_params(phydev, cfg_results);
194 }
195
lan865x_revb0_config_init(struct phy_device * phydev)196 static int lan865x_revb0_config_init(struct phy_device *phydev)
197 {
198 int ret;
199
200 /* Reference to AN1760
201 * https://ww1.microchip.com/downloads/aemDocuments/documents/AIS/ProductDocuments/SupportingCollateral/AN-LAN8650-1-Configuration-60001760.pdf
202 */
203 for (int i = 0; i < ARRAY_SIZE(lan865x_revb0_fixup_registers); i++) {
204 ret = phy_write_mmd(phydev, MDIO_MMD_VEND2,
205 lan865x_revb0_fixup_registers[i],
206 lan865x_revb0_fixup_values[i]);
207 if (ret)
208 return ret;
209 }
210 /* Function to calculate and write the configuration parameters in the
211 * 0x0084, 0x008A, 0x00AD, 0x00AE and 0x00AF registers (from AN1760)
212 */
213 return lan865x_setup_cfgparam(phydev);
214 }
215
lan867x_revb1_config_init(struct phy_device * phydev)216 static int lan867x_revb1_config_init(struct phy_device *phydev)
217 {
218 int err;
219
220 /* The chip completes a reset in 3us, we might get here earlier than
221 * that, as an added margin we'll conditionally sleep 5us.
222 */
223 err = phy_read_mmd(phydev, MDIO_MMD_VEND2, LAN867X_REG_STS2);
224 if (err < 0)
225 return err;
226
227 if (!(err & LAN867x_RESET_COMPLETE_STS)) {
228 udelay(5);
229 err = phy_read_mmd(phydev, MDIO_MMD_VEND2, LAN867X_REG_STS2);
230 if (err < 0)
231 return err;
232 if (!(err & LAN867x_RESET_COMPLETE_STS)) {
233 phydev_err(phydev, "PHY reset failed\n");
234 return -ENODEV;
235 }
236 }
237
238 /* Reference to AN1699
239 * https://ww1.microchip.com/downloads/aemDocuments/documents/AIS/ProductDocuments/SupportingCollateral/AN-LAN8670-1-2-config-60001699.pdf
240 * AN1699 says Read, Modify, Write, but the Write is not required if the
241 * register already has the required value. So it is safe to use
242 * phy_modify_mmd here.
243 */
244 for (int i = 0; i < ARRAY_SIZE(lan867x_revb1_fixup_registers); i++) {
245 err = phy_modify_mmd(phydev, MDIO_MMD_VEND2,
246 lan867x_revb1_fixup_registers[i],
247 lan867x_revb1_fixup_masks[i],
248 lan867x_revb1_fixup_values[i]);
249 if (err)
250 return err;
251 }
252
253 return 0;
254 }
255
lan86xx_read_status(struct phy_device * phydev)256 static int lan86xx_read_status(struct phy_device *phydev)
257 {
258 /* The phy has some limitations, namely:
259 * - always reports link up
260 * - only supports 10MBit half duplex
261 * - does not support auto negotiate
262 */
263 phydev->link = 1;
264 phydev->duplex = DUPLEX_HALF;
265 phydev->speed = SPEED_10;
266 phydev->autoneg = AUTONEG_DISABLE;
267
268 return 0;
269 }
270
271 static struct phy_driver microchip_t1s_driver[] = {
272 {
273 PHY_ID_MATCH_EXACT(PHY_ID_LAN867X_REVB1),
274 .name = "LAN867X Rev.B1",
275 .features = PHY_BASIC_T1S_P2MP_FEATURES,
276 .config_init = lan867x_revb1_config_init,
277 .read_status = lan86xx_read_status,
278 .get_plca_cfg = genphy_c45_plca_get_cfg,
279 .set_plca_cfg = genphy_c45_plca_set_cfg,
280 .get_plca_status = genphy_c45_plca_get_status,
281 },
282 {
283 PHY_ID_MATCH_EXACT(PHY_ID_LAN865X_REVB0),
284 .name = "LAN865X Rev.B0 Internal Phy",
285 .features = PHY_BASIC_T1S_P2MP_FEATURES,
286 .config_init = lan865x_revb0_config_init,
287 .read_status = lan86xx_read_status,
288 .get_plca_cfg = genphy_c45_plca_get_cfg,
289 .set_plca_cfg = genphy_c45_plca_set_cfg,
290 .get_plca_status = genphy_c45_plca_get_status,
291 },
292 };
293
294 module_phy_driver(microchip_t1s_driver);
295
296 static struct mdio_device_id __maybe_unused tbl[] = {
297 { PHY_ID_MATCH_EXACT(PHY_ID_LAN867X_REVB1) },
298 { PHY_ID_MATCH_EXACT(PHY_ID_LAN865X_REVB0) },
299 { }
300 };
301
302 MODULE_DEVICE_TABLE(mdio, tbl);
303
304 MODULE_DESCRIPTION("Microchip 10BASE-T1S PHYs driver");
305 MODULE_AUTHOR("Ramón Nordin Rodriguez");
306 MODULE_LICENSE("GPL");
307