1 // SPDX-License-Identifier: GPL-2.0
2 #include <linux/linkage.h>
3 #include <linux/errno.h>
4 #include <linux/signal.h>
5 #include <linux/sched.h>
6 #include <linux/ioport.h>
7 #include <linux/interrupt.h>
8 #include <linux/irq.h>
9 #include <linux/timex.h>
10 #include <linux/random.h>
11 #include <linux/kprobes.h>
12 #include <linux/init.h>
13 #include <linux/kernel_stat.h>
14 #include <linux/device.h>
15 #include <linux/bitops.h>
16 #include <linux/acpi.h>
17 #include <linux/io.h>
18 #include <linux/delay.h>
19 #include <linux/pgtable.h>
20
21 #include <linux/atomic.h>
22 #include <asm/timer.h>
23 #include <asm/hw_irq.h>
24 #include <asm/desc.h>
25 #include <asm/io_apic.h>
26 #include <asm/acpi.h>
27 #include <asm/apic.h>
28 #include <asm/setup.h>
29 #include <asm/i8259.h>
30 #include <asm/traps.h>
31 #include <asm/prom.h>
32
33 /*
34 * ISA PIC or low IO-APIC triggered (INTA-cycle or APIC) interrupts:
35 * (these are usually mapped to vectors 0x30-0x3f)
36 */
37
38 /*
39 * The IO-APIC gives us many more interrupt sources. Most of these
40 * are unused but an SMP system is supposed to have enough memory ...
41 * sometimes (mostly wrt. hw bugs) we get corrupted vectors all
42 * across the spectrum, so we really want to be prepared to get all
43 * of these. Plus, more powerful systems might have more than 64
44 * IO-APIC registers.
45 *
46 * (these are usually mapped into the 0x30-0xff vector range)
47 */
48
49 DEFINE_PER_CPU(vector_irq_t, vector_irq) = {
50 [0 ... NR_VECTORS - 1] = VECTOR_UNUSED,
51 };
52
init_ISA_irqs(void)53 void __init init_ISA_irqs(void)
54 {
55 struct irq_chip *chip = legacy_pic->chip;
56 int i;
57
58 /*
59 * Try to set up the through-local-APIC virtual wire mode earlier.
60 *
61 * On some 32-bit UP machines, whose APIC has been disabled by BIOS
62 * and then got re-enabled by "lapic", it hangs at boot time without this.
63 */
64 init_bsp_APIC();
65
66 legacy_pic->init(0);
67
68 for (i = 0; i < nr_legacy_irqs(); i++) {
69 irq_set_chip_and_handler(i, chip, handle_level_irq);
70 irq_set_status_flags(i, IRQ_LEVEL);
71 }
72 }
73
init_IRQ(void)74 void __init init_IRQ(void)
75 {
76 int i;
77
78 /*
79 * On cpu 0, Assign ISA_IRQ_VECTOR(irq) to IRQ 0..15.
80 * If these IRQ's are handled by legacy interrupt-controllers like PIC,
81 * then this configuration will likely be static after the boot. If
82 * these IRQs are handled by more modern controllers like IO-APIC,
83 * then this vector space can be freed and re-used dynamically as the
84 * irq's migrate etc.
85 */
86 for (i = 0; i < nr_legacy_irqs(); i++)
87 per_cpu(vector_irq, 0)[ISA_IRQ_VECTOR(i)] = irq_to_desc(i);
88
89 BUG_ON(irq_init_percpu_irqstack(smp_processor_id()));
90
91 x86_init.irqs.intr_init();
92 }
93
native_init_IRQ(void)94 void __init native_init_IRQ(void)
95 {
96 /* Execute any quirks before the call gates are initialised: */
97 x86_init.irqs.pre_vector_init();
98
99 idt_setup_apic_and_irq_gates();
100 lapic_assign_system_vectors();
101
102 if (!acpi_ioapic && !of_ioapic && nr_legacy_irqs()) {
103 /* IRQ2 is cascade interrupt to second interrupt controller */
104 if (request_irq(2, no_action, IRQF_NO_THREAD, "cascade", NULL))
105 pr_err("%s: request_irq() failed\n", "cascade");
106 }
107 }
108