1 // SPDX-License-Identifier: GPL-2.0
2 /* Copyright (c) 2018 Intel Corporation */
3
4 #include <linux/delay.h>
5
6 #include "igc_hw.h"
7 #include "igc_i225.h"
8 #include "igc_mac.h"
9 #include "igc_base.h"
10 #include "igc.h"
11
12 /**
13 * igc_reset_hw_base - Reset hardware
14 * @hw: pointer to the HW structure
15 *
16 * This resets the hardware into a known state. This is a
17 * function pointer entry point called by the api module.
18 */
igc_reset_hw_base(struct igc_hw * hw)19 static s32 igc_reset_hw_base(struct igc_hw *hw)
20 {
21 s32 ret_val;
22 u32 ctrl;
23
24 /* Prevent the PCI-E bus from sticking if there is no TLP connection
25 * on the last TLP read/write transaction when MAC is reset.
26 */
27 ret_val = igc_disable_pcie_master(hw);
28 if (ret_val)
29 hw_dbg("PCI-E Master disable polling has failed\n");
30
31 hw_dbg("Masking off all interrupts\n");
32 wr32(IGC_IMC, 0xffffffff);
33
34 wr32(IGC_RCTL, 0);
35 wr32(IGC_TCTL, IGC_TCTL_PSP);
36 wrfl();
37
38 usleep_range(10000, 20000);
39
40 ctrl = rd32(IGC_CTRL);
41
42 hw_dbg("Issuing a global reset to MAC\n");
43 wr32(IGC_CTRL, ctrl | IGC_CTRL_RST);
44
45 ret_val = igc_get_auto_rd_done(hw);
46 if (ret_val) {
47 /* When auto config read does not complete, do not
48 * return with an error. This can happen in situations
49 * where there is no eeprom and prevents getting link.
50 */
51 hw_dbg("Auto Read Done did not complete\n");
52 }
53
54 /* Clear any pending interrupt events. */
55 wr32(IGC_IMC, 0xffffffff);
56 rd32(IGC_ICR);
57
58 return ret_val;
59 }
60
61 /**
62 * igc_init_nvm_params_base - Init NVM func ptrs.
63 * @hw: pointer to the HW structure
64 */
igc_init_nvm_params_base(struct igc_hw * hw)65 static s32 igc_init_nvm_params_base(struct igc_hw *hw)
66 {
67 struct igc_nvm_info *nvm = &hw->nvm;
68 u32 eecd = rd32(IGC_EECD);
69 u16 size;
70
71 size = (u16)((eecd & IGC_EECD_SIZE_EX_MASK) >>
72 IGC_EECD_SIZE_EX_SHIFT);
73
74 /* Added to a constant, "size" becomes the left-shift value
75 * for setting word_size.
76 */
77 size += NVM_WORD_SIZE_BASE_SHIFT;
78
79 /* Just in case size is out of range, cap it to the largest
80 * EEPROM size supported
81 */
82 if (size > 15)
83 size = 15;
84
85 nvm->type = igc_nvm_eeprom_spi;
86 nvm->word_size = BIT(size);
87 nvm->opcode_bits = 8;
88 nvm->delay_usec = 1;
89
90 nvm->page_size = eecd & IGC_EECD_ADDR_BITS ? 32 : 8;
91 nvm->address_bits = eecd & IGC_EECD_ADDR_BITS ?
92 16 : 8;
93
94 if (nvm->word_size == BIT(15))
95 nvm->page_size = 128;
96
97 return 0;
98 }
99
100 /**
101 * igc_setup_copper_link_base - Configure copper link settings
102 * @hw: pointer to the HW structure
103 *
104 * Configures the link for auto-neg or forced speed and duplex. Then we check
105 * for link, once link is established calls to configure collision distance
106 * and flow control are called.
107 */
igc_setup_copper_link_base(struct igc_hw * hw)108 static s32 igc_setup_copper_link_base(struct igc_hw *hw)
109 {
110 s32 ret_val = 0;
111 u32 ctrl;
112
113 ctrl = rd32(IGC_CTRL);
114 ctrl |= IGC_CTRL_SLU;
115 ctrl &= ~(IGC_CTRL_FRCSPD | IGC_CTRL_FRCDPX);
116 wr32(IGC_CTRL, ctrl);
117
118 ret_val = igc_setup_copper_link(hw);
119
120 return ret_val;
121 }
122
123 /**
124 * igc_init_mac_params_base - Init MAC func ptrs.
125 * @hw: pointer to the HW structure
126 */
igc_init_mac_params_base(struct igc_hw * hw)127 static s32 igc_init_mac_params_base(struct igc_hw *hw)
128 {
129 struct igc_dev_spec_base *dev_spec = &hw->dev_spec._base;
130 struct igc_mac_info *mac = &hw->mac;
131
132 /* Set mta register count */
133 mac->mta_reg_count = 128;
134 mac->rar_entry_count = IGC_RAR_ENTRIES;
135
136 /* reset */
137 mac->ops.reset_hw = igc_reset_hw_base;
138
139 mac->ops.acquire_swfw_sync = igc_acquire_swfw_sync_i225;
140 mac->ops.release_swfw_sync = igc_release_swfw_sync_i225;
141
142 /* Allow a single clear of the SW semaphore on I225 */
143 if (mac->type == igc_i225)
144 dev_spec->clear_semaphore_once = true;
145
146 /* physical interface link setup */
147 mac->ops.setup_physical_interface = igc_setup_copper_link_base;
148
149 return 0;
150 }
151
152 /**
153 * igc_init_phy_params_base - Init PHY func ptrs.
154 * @hw: pointer to the HW structure
155 */
igc_init_phy_params_base(struct igc_hw * hw)156 static s32 igc_init_phy_params_base(struct igc_hw *hw)
157 {
158 struct igc_phy_info *phy = &hw->phy;
159 s32 ret_val = 0;
160
161 phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT_2500;
162 phy->reset_delay_us = 100;
163
164 /* set lan id */
165 hw->bus.func = (rd32(IGC_STATUS) & IGC_STATUS_FUNC_MASK) >>
166 IGC_STATUS_FUNC_SHIFT;
167
168 /* Make sure the PHY is in a good state. Several people have reported
169 * firmware leaving the PHY's page select register set to something
170 * other than the default of zero, which causes the PHY ID read to
171 * access something other than the intended register.
172 */
173 ret_val = hw->phy.ops.reset(hw);
174 if (ret_val) {
175 hw_dbg("Error resetting the PHY\n");
176 goto out;
177 }
178
179 ret_val = igc_get_phy_id(hw);
180 if (ret_val)
181 return ret_val;
182
183 igc_check_for_copper_link(hw);
184
185 out:
186 return ret_val;
187 }
188
igc_get_invariants_base(struct igc_hw * hw)189 static s32 igc_get_invariants_base(struct igc_hw *hw)
190 {
191 struct igc_mac_info *mac = &hw->mac;
192 s32 ret_val = 0;
193
194 switch (hw->device_id) {
195 case IGC_DEV_ID_I225_LM:
196 case IGC_DEV_ID_I225_V:
197 case IGC_DEV_ID_I225_I:
198 case IGC_DEV_ID_I220_V:
199 case IGC_DEV_ID_I225_K:
200 case IGC_DEV_ID_I225_K2:
201 case IGC_DEV_ID_I226_K:
202 case IGC_DEV_ID_I225_LMVP:
203 case IGC_DEV_ID_I226_LMVP:
204 case IGC_DEV_ID_I225_IT:
205 case IGC_DEV_ID_I226_LM:
206 case IGC_DEV_ID_I226_V:
207 case IGC_DEV_ID_I226_IT:
208 case IGC_DEV_ID_I221_V:
209 case IGC_DEV_ID_I226_BLANK_NVM:
210 case IGC_DEV_ID_I225_BLANK_NVM:
211 mac->type = igc_i225;
212 break;
213 default:
214 return -IGC_ERR_MAC_INIT;
215 }
216
217 hw->phy.media_type = igc_media_type_copper;
218
219 /* mac initialization and operations */
220 ret_val = igc_init_mac_params_base(hw);
221 if (ret_val)
222 goto out;
223
224 /* NVM initialization */
225 ret_val = igc_init_nvm_params_base(hw);
226 switch (hw->mac.type) {
227 case igc_i225:
228 ret_val = igc_init_nvm_params_i225(hw);
229 break;
230 default:
231 break;
232 }
233
234 /* setup PHY parameters */
235 ret_val = igc_init_phy_params_base(hw);
236 if (ret_val)
237 goto out;
238
239 out:
240 return ret_val;
241 }
242
243 /**
244 * igc_acquire_phy_base - Acquire rights to access PHY
245 * @hw: pointer to the HW structure
246 *
247 * Acquire access rights to the correct PHY. This is a
248 * function pointer entry point called by the api module.
249 */
igc_acquire_phy_base(struct igc_hw * hw)250 static s32 igc_acquire_phy_base(struct igc_hw *hw)
251 {
252 u16 mask = IGC_SWFW_PHY0_SM;
253
254 return hw->mac.ops.acquire_swfw_sync(hw, mask);
255 }
256
257 /**
258 * igc_release_phy_base - Release rights to access PHY
259 * @hw: pointer to the HW structure
260 *
261 * A wrapper to release access rights to the correct PHY. This is a
262 * function pointer entry point called by the api module.
263 */
igc_release_phy_base(struct igc_hw * hw)264 static void igc_release_phy_base(struct igc_hw *hw)
265 {
266 u16 mask = IGC_SWFW_PHY0_SM;
267
268 hw->mac.ops.release_swfw_sync(hw, mask);
269 }
270
271 /**
272 * igc_init_hw_base - Initialize hardware
273 * @hw: pointer to the HW structure
274 *
275 * This inits the hardware readying it for operation.
276 */
igc_init_hw_base(struct igc_hw * hw)277 static s32 igc_init_hw_base(struct igc_hw *hw)
278 {
279 struct igc_mac_info *mac = &hw->mac;
280 u16 i, rar_count = mac->rar_entry_count;
281 s32 ret_val = 0;
282
283 /* Setup the receive address */
284 igc_init_rx_addrs(hw, rar_count);
285
286 /* Zero out the Multicast HASH table */
287 hw_dbg("Zeroing the MTA\n");
288 for (i = 0; i < mac->mta_reg_count; i++)
289 array_wr32(IGC_MTA, i, 0);
290
291 /* Zero out the Unicast HASH table */
292 hw_dbg("Zeroing the UTA\n");
293 for (i = 0; i < mac->uta_reg_count; i++)
294 array_wr32(IGC_UTA, i, 0);
295
296 /* Setup link and flow control */
297 ret_val = igc_setup_link(hw);
298
299 /* Clear all of the statistics registers (clear on read). It is
300 * important that we do this after we have tried to establish link
301 * because the symbol error count will increment wildly if there
302 * is no link.
303 */
304 igc_clear_hw_cntrs_base(hw);
305
306 return ret_val;
307 }
308
309 /**
310 * igc_power_down_phy_copper_base - Remove link during PHY power down
311 * @hw: pointer to the HW structure
312 *
313 * In the case of a PHY power down to save power, or to turn off link during a
314 * driver unload, or wake on lan is not enabled, remove the link.
315 */
igc_power_down_phy_copper_base(struct igc_hw * hw)316 void igc_power_down_phy_copper_base(struct igc_hw *hw)
317 {
318 /* If the management interface is not enabled, then power down */
319 if (!(igc_enable_mng_pass_thru(hw) || igc_check_reset_block(hw)))
320 igc_power_down_phy_copper(hw);
321 }
322
323 /**
324 * igc_rx_fifo_flush_base - Clean rx fifo after Rx enable
325 * @hw: pointer to the HW structure
326 *
327 * After Rx enable, if manageability is enabled then there is likely some
328 * bad data at the start of the fifo and possibly in the DMA fifo. This
329 * function clears the fifos and flushes any packets that came in as rx was
330 * being enabled.
331 */
igc_rx_fifo_flush_base(struct igc_hw * hw)332 void igc_rx_fifo_flush_base(struct igc_hw *hw)
333 {
334 u32 rctl, rlpml, rxdctl[4], rfctl, temp_rctl, rx_enabled;
335 int i, ms_wait;
336
337 /* disable IPv6 options as per hardware errata */
338 rfctl = rd32(IGC_RFCTL);
339 rfctl |= IGC_RFCTL_IPV6_EX_DIS;
340 wr32(IGC_RFCTL, rfctl);
341
342 if (!(rd32(IGC_MANC) & IGC_MANC_RCV_TCO_EN))
343 return;
344
345 /* Disable all Rx queues */
346 for (i = 0; i < 4; i++) {
347 rxdctl[i] = rd32(IGC_RXDCTL(i));
348 wr32(IGC_RXDCTL(i),
349 rxdctl[i] & ~IGC_RXDCTL_QUEUE_ENABLE);
350 }
351 /* Poll all queues to verify they have shut down */
352 for (ms_wait = 0; ms_wait < 10; ms_wait++) {
353 usleep_range(1000, 2000);
354 rx_enabled = 0;
355 for (i = 0; i < 4; i++)
356 rx_enabled |= rd32(IGC_RXDCTL(i));
357 if (!(rx_enabled & IGC_RXDCTL_QUEUE_ENABLE))
358 break;
359 }
360
361 if (ms_wait == 10)
362 hw_dbg("Queue disable timed out after 10ms\n");
363
364 /* Clear RLPML, RCTL.SBP, RFCTL.LEF, and set RCTL.LPE so that all
365 * incoming packets are rejected. Set enable and wait 2ms so that
366 * any packet that was coming in as RCTL.EN was set is flushed
367 */
368 wr32(IGC_RFCTL, rfctl & ~IGC_RFCTL_LEF);
369
370 rlpml = rd32(IGC_RLPML);
371 wr32(IGC_RLPML, 0);
372
373 rctl = rd32(IGC_RCTL);
374 temp_rctl = rctl & ~(IGC_RCTL_EN | IGC_RCTL_SBP);
375 temp_rctl |= IGC_RCTL_LPE;
376
377 wr32(IGC_RCTL, temp_rctl);
378 wr32(IGC_RCTL, temp_rctl | IGC_RCTL_EN);
379 wrfl();
380 usleep_range(2000, 3000);
381
382 /* Enable Rx queues that were previously enabled and restore our
383 * previous state
384 */
385 for (i = 0; i < 4; i++)
386 wr32(IGC_RXDCTL(i), rxdctl[i]);
387 wr32(IGC_RCTL, rctl);
388 wrfl();
389
390 wr32(IGC_RLPML, rlpml);
391 wr32(IGC_RFCTL, rfctl);
392
393 /* Flush receive errors generated by workaround */
394 rd32(IGC_ROC);
395 rd32(IGC_RNBC);
396 rd32(IGC_MPC);
397 }
398
igc_is_device_id_i225(struct igc_hw * hw)399 bool igc_is_device_id_i225(struct igc_hw *hw)
400 {
401 switch (hw->device_id) {
402 case IGC_DEV_ID_I225_LM:
403 case IGC_DEV_ID_I225_V:
404 case IGC_DEV_ID_I225_I:
405 case IGC_DEV_ID_I225_K:
406 case IGC_DEV_ID_I225_K2:
407 case IGC_DEV_ID_I225_LMVP:
408 case IGC_DEV_ID_I225_IT:
409 return true;
410 default:
411 return false;
412 }
413 }
414
igc_is_device_id_i226(struct igc_hw * hw)415 bool igc_is_device_id_i226(struct igc_hw *hw)
416 {
417 switch (hw->device_id) {
418 case IGC_DEV_ID_I226_LM:
419 case IGC_DEV_ID_I226_V:
420 case IGC_DEV_ID_I226_K:
421 case IGC_DEV_ID_I226_IT:
422 return true;
423 default:
424 return false;
425 }
426 }
427
428 static struct igc_mac_operations igc_mac_ops_base = {
429 .init_hw = igc_init_hw_base,
430 .check_for_link = igc_check_for_copper_link,
431 .rar_set = igc_rar_set,
432 .read_mac_addr = igc_read_mac_addr,
433 .get_speed_and_duplex = igc_get_speed_and_duplex_copper,
434 };
435
436 static const struct igc_phy_operations igc_phy_ops_base = {
437 .acquire = igc_acquire_phy_base,
438 .release = igc_release_phy_base,
439 .reset = igc_phy_hw_reset,
440 .read_reg = igc_read_phy_reg_gpy,
441 .write_reg = igc_write_phy_reg_gpy,
442 };
443
444 const struct igc_info igc_base_info = {
445 .get_invariants = igc_get_invariants_base,
446 .mac_ops = &igc_mac_ops_base,
447 .phy_ops = &igc_phy_ops_base,
448 };
449