1 // SPDX-License-Identifier: GPL-2.0
2 /*
3  * Driver for the 98626/98644/internal serial interface on hp300/hp400
4  * (based on the National Semiconductor INS8250/NS16550AF/WD16C552 UARTs)
5  *
6  * Ported from 2.2 and modified to use the normal 8250 driver
7  * by Kars de Jong <jongk@linux-m68k.org>, May 2004.
8  */
9 #include <linux/module.h>
10 #include <linux/init.h>
11 #include <linux/string.h>
12 #include <linux/kernel.h>
13 #include <linux/serial.h>
14 #include <linux/serial_8250.h>
15 #include <linux/delay.h>
16 #include <linux/dio.h>
17 #include <linux/console.h>
18 #include <linux/slab.h>
19 #include <asm/io.h>
20 
21 #include "8250.h"
22 
23 #if !defined(CONFIG_HPDCA) && !defined(CONFIG_HPAPCI) && !defined(CONFIG_COMPILE_TEST)
24 #warning CONFIG_SERIAL_8250 defined but neither CONFIG_HPDCA nor CONFIG_HPAPCI defined, are you sure?
25 #endif
26 
27 #ifdef CONFIG_HPAPCI
28 struct hp300_port {
29 	struct hp300_port *next;	/* next port */
30 	int line;			/* line (tty) number */
31 };
32 
33 static struct hp300_port *hp300_ports;
34 #endif
35 
36 #ifdef CONFIG_HPDCA
37 
38 static int hpdca_init_one(struct dio_dev *d,
39 					const struct dio_device_id *ent);
40 static void hpdca_remove_one(struct dio_dev *d);
41 
42 static struct dio_device_id hpdca_dio_tbl[] = {
43 	{ DIO_ID_DCA0 },
44 	{ DIO_ID_DCA0REM },
45 	{ DIO_ID_DCA1 },
46 	{ DIO_ID_DCA1REM },
47 	{ 0 }
48 };
49 
50 static struct dio_driver hpdca_driver = {
51 	.name      = "hpdca",
52 	.id_table  = hpdca_dio_tbl,
53 	.probe     = hpdca_init_one,
54 	.remove    = hpdca_remove_one,
55 };
56 
57 #endif
58 
59 static unsigned int num_ports;
60 
61 extern int hp300_uart_scode;
62 
63 /* Offset to UART registers from base of DCA */
64 #define UART_OFFSET	17
65 
66 #define DCA_ID		0x01	/* ID (read), reset (write) */
67 #define DCA_IC		0x03	/* Interrupt control        */
68 
69 /* Interrupt control */
70 #define DCA_IC_IE	0x80	/* Master interrupt enable  */
71 
72 #define HPDCA_BAUD_BASE 153600
73 
74 /* Base address of the Frodo part */
75 #define FRODO_BASE	(0x41c000)
76 
77 /*
78  * Where we find the 8250-like APCI ports, and how far apart they are.
79  */
80 #define FRODO_APCIBASE		0x0
81 #define FRODO_APCISPACE		0x20
82 #define FRODO_APCI_OFFSET(x)	(FRODO_APCIBASE + ((x) * FRODO_APCISPACE))
83 
84 #define HPAPCI_BAUD_BASE 500400
85 
86 #ifdef CONFIG_SERIAL_8250_CONSOLE
87 /*
88  * Parse the bootinfo to find descriptions for headless console and
89  * debug serial ports and register them with the 8250 driver.
90  */
hp300_setup_serial_console(void)91 int __init hp300_setup_serial_console(void)
92 {
93 	int scode;
94 	struct uart_port port;
95 
96 	memset(&port, 0, sizeof(port));
97 
98 	if (hp300_uart_scode < 0 || hp300_uart_scode > DIO_SCMAX)
99 		return 0;
100 
101 	if (DIO_SCINHOLE(hp300_uart_scode))
102 		return 0;
103 
104 	scode = hp300_uart_scode;
105 
106 	/* Memory mapped I/O */
107 	port.iotype = UPIO_MEM;
108 	port.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF;
109 	port.type = PORT_UNKNOWN;
110 
111 	/* Check for APCI console */
112 	if (scode == 256) {
113 #ifdef CONFIG_HPAPCI
114 		pr_info("Serial console is HP APCI 1\n");
115 
116 		port.uartclk = HPAPCI_BAUD_BASE * 16;
117 		port.mapbase = (FRODO_BASE + FRODO_APCI_OFFSET(1));
118 		port.membase = (char *)(port.mapbase + DIO_VIRADDRBASE);
119 		port.regshift = 2;
120 		add_preferred_console("ttyS", port.line, "9600n8");
121 #else
122 		pr_warn("Serial console is APCI but support is disabled (CONFIG_HPAPCI)!\n");
123 		return 0;
124 #endif
125 	} else {
126 #ifdef CONFIG_HPDCA
127 		unsigned long pa = dio_scodetophysaddr(scode);
128 		if (!pa)
129 			return 0;
130 
131 		pr_info("Serial console is HP DCA at select code %d\n", scode);
132 
133 		port.uartclk = HPDCA_BAUD_BASE * 16;
134 		port.mapbase = (pa + UART_OFFSET);
135 		port.membase = (char *)(port.mapbase + DIO_VIRADDRBASE);
136 		port.regshift = 1;
137 		port.irq = DIO_IPL(pa + DIO_VIRADDRBASE);
138 
139 		/* Enable board-interrupts */
140 		out_8(pa + DIO_VIRADDRBASE + DCA_IC, DCA_IC_IE);
141 
142 		if (DIO_ID(pa + DIO_VIRADDRBASE) & 0x80)
143 			add_preferred_console("ttyS", port.line, "9600n8");
144 #else
145 		pr_warn("Serial console is DCA but support is disabled (CONFIG_HPDCA)!\n");
146 		return 0;
147 #endif
148 	}
149 
150 	if (early_serial_setup(&port) < 0)
151 		pr_warn("%s: early_serial_setup() failed.\n", __func__);
152 	return 0;
153 }
154 #endif /* CONFIG_SERIAL_8250_CONSOLE */
155 
156 #ifdef CONFIG_HPDCA
hpdca_init_one(struct dio_dev * d,const struct dio_device_id * ent)157 static int hpdca_init_one(struct dio_dev *d,
158 				const struct dio_device_id *ent)
159 {
160 	struct uart_8250_port uart;
161 	int line;
162 
163 #ifdef CONFIG_SERIAL_8250_CONSOLE
164 	if (hp300_uart_scode == d->scode) {
165 		/* Already got it. */
166 		return 0;
167 	}
168 #endif
169 	memset(&uart, 0, sizeof(uart));
170 
171 	/* Memory mapped I/O */
172 	uart.port.iotype = UPIO_MEM;
173 	uart.port.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF;
174 	uart.port.irq = d->ipl;
175 	uart.port.uartclk = HPDCA_BAUD_BASE * 16;
176 	uart.port.mapbase = (d->resource.start + UART_OFFSET);
177 	uart.port.membase = (char *)(uart.port.mapbase + DIO_VIRADDRBASE);
178 	uart.port.regshift = 1;
179 	uart.port.dev = &d->dev;
180 	line = serial8250_register_8250_port(&uart);
181 
182 	if (line < 0) {
183 		dev_notice(&d->dev,
184 			  "8250_hp300: register_serial() DCA scode %d irq %d failed\n",
185 			  d->scode, uart.port.irq);
186 		return -ENOMEM;
187 	}
188 
189 	/* Enable board-interrupts */
190 	out_8(d->resource.start + DIO_VIRADDRBASE + DCA_IC, DCA_IC_IE);
191 	dio_set_drvdata(d, (void *)line);
192 
193 	/* Reset the DCA */
194 	out_8(d->resource.start + DIO_VIRADDRBASE + DCA_ID, 0xff);
195 	udelay(100);
196 
197 	num_ports++;
198 
199 	return 0;
200 }
201 #endif
202 
hp300_8250_init(void)203 static int __init hp300_8250_init(void)
204 {
205 	static int called;
206 #ifdef CONFIG_HPAPCI
207 	int line;
208 	unsigned long base;
209 	struct uart_8250_port uart;
210 	struct hp300_port *port;
211 	int i;
212 #endif
213 	if (called)
214 		return -ENODEV;
215 	called = 1;
216 
217 	if (!MACH_IS_HP300)
218 		return -ENODEV;
219 
220 #ifdef CONFIG_HPDCA
221 	dio_register_driver(&hpdca_driver);
222 #endif
223 #ifdef CONFIG_HPAPCI
224 	if (hp300_model < HP_400) {
225 		if (!num_ports)
226 			return -ENODEV;
227 		return 0;
228 	}
229 	/* These models have the Frodo chip.
230 	 * Port 0 is reserved for the Apollo Domain keyboard.
231 	 * Port 1 is either the console or the DCA.
232 	 */
233 	for (i = 1; i < 4; i++) {
234 		/* Port 1 is the console on a 425e, on other machines it's
235 		 * mapped to DCA.
236 		 */
237 #ifdef CONFIG_SERIAL_8250_CONSOLE
238 		if (i == 1)
239 			continue;
240 #endif
241 
242 		/* Create new serial device */
243 		port = kmalloc(sizeof(struct hp300_port), GFP_KERNEL);
244 		if (!port)
245 			return -ENOMEM;
246 
247 		memset(&uart, 0, sizeof(uart));
248 
249 		base = (FRODO_BASE + FRODO_APCI_OFFSET(i));
250 
251 		/* Memory mapped I/O */
252 		uart.port.iotype = UPIO_MEM;
253 		uart.port.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ
254 				| UPF_BOOT_AUTOCONF;
255 		/* XXX - no interrupt support yet */
256 		uart.port.irq = 0;
257 		uart.port.uartclk = HPAPCI_BAUD_BASE * 16;
258 		uart.port.mapbase = base;
259 		uart.port.membase = (char *)(base + DIO_VIRADDRBASE);
260 		uart.port.regshift = 2;
261 
262 		line = serial8250_register_8250_port(&uart);
263 
264 		if (line < 0) {
265 			dev_notice(uart.port.dev,
266 				   "8250_hp300: register_serial() APCI %d irq %d failed\n",
267 				   i, uart.port.irq);
268 			kfree(port);
269 			continue;
270 		}
271 
272 		port->line = line;
273 		port->next = hp300_ports;
274 		hp300_ports = port;
275 
276 		num_ports++;
277 	}
278 #endif
279 
280 	/* Any boards found? */
281 	if (!num_ports)
282 		return -ENODEV;
283 
284 	return 0;
285 }
286 
287 #ifdef CONFIG_HPDCA
hpdca_remove_one(struct dio_dev * d)288 static void hpdca_remove_one(struct dio_dev *d)
289 {
290 	int line;
291 
292 	line = (int) dio_get_drvdata(d);
293 	if (d->resource.start) {
294 		/* Disable board-interrupts */
295 		out_8(d->resource.start + DIO_VIRADDRBASE + DCA_IC, 0);
296 	}
297 	serial8250_unregister_port(line);
298 }
299 #endif
300 
hp300_8250_exit(void)301 static void __exit hp300_8250_exit(void)
302 {
303 #ifdef CONFIG_HPAPCI
304 	struct hp300_port *port, *to_free;
305 
306 	for (port = hp300_ports; port; ) {
307 		serial8250_unregister_port(port->line);
308 		to_free = port;
309 		port = port->next;
310 		kfree(to_free);
311 	}
312 
313 	hp300_ports = NULL;
314 #endif
315 #ifdef CONFIG_HPDCA
316 	dio_unregister_driver(&hpdca_driver);
317 #endif
318 }
319 
320 module_init(hp300_8250_init);
321 module_exit(hp300_8250_exit);
322 MODULE_DESCRIPTION("HP DCA/APCI serial driver");
323 MODULE_AUTHOR("Kars de Jong <jongk@linux-m68k.org>");
324 MODULE_LICENSE("GPL");
325