1 /* hermes.c
2 *
3 * Driver core for the "Hermes" wireless MAC controller, as used in
4 * the Lucent Orinoco and Cabletron RoamAbout cards. It should also
5 * work on the hfa3841 and hfa3842 MAC controller chips used in the
6 * Prism II chipsets.
7 *
8 * This is not a complete driver, just low-level access routines for
9 * the MAC controller itself.
10 *
11 * Based on the prism2 driver from Absolute Value Systems' linux-wlan
12 * project, the Linux wvlan_cs driver, Lucent's HCF-Light
13 * (wvlan_hcf.c) library, and the NetBSD wireless driver (in no
14 * particular order).
15 *
16 * Copyright (C) 2000, David Gibson, Linuxcare Australia.
17 * (C) Copyright David Gibson, IBM Corp. 2001-2003.
18 *
19 * The contents of this file are subject to the Mozilla Public License
20 * Version 1.1 (the "License"); you may not use this file except in
21 * compliance with the License. You may obtain a copy of the License
22 * at http://www.mozilla.org/MPL/
23 *
24 * Software distributed under the License is distributed on an "AS IS"
25 * basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See
26 * the License for the specific language governing rights and
27 * limitations under the License.
28 *
29 * Alternatively, the contents of this file may be used under the
30 * terms of the GNU General Public License version 2 (the "GPL"), in
31 * which case the provisions of the GPL are applicable instead of the
32 * above. If you wish to allow the use of your version of this file
33 * only under the terms of the GPL and not to allow others to use your
34 * version of this file under the MPL, indicate your decision by
35 * deleting the provisions above and replace them with the notice and
36 * other provisions required by the GPL. If you do not delete the
37 * provisions above, a recipient may use your version of this file
38 * under either the MPL or the GPL.
39 */
40
41 #include <linux/net.h>
42 #include <linux/module.h>
43 #include <linux/kernel.h>
44 #include <linux/delay.h>
45
46 #include "hermes.h"
47
48 /* These are maximum timeouts. Most often, card wil react much faster */
49 #define CMD_BUSY_TIMEOUT (100) /* In iterations of ~1us */
50 #define CMD_INIT_TIMEOUT (50000) /* in iterations of ~10us */
51 #define CMD_COMPL_TIMEOUT (20000) /* in iterations of ~10us */
52 #define ALLOC_COMPL_TIMEOUT (1000) /* in iterations of ~10us */
53
54 /*
55 * AUX port access. To unlock the AUX port write the access keys to the
56 * PARAM0-2 registers, then write HERMES_AUX_ENABLE to the HERMES_CONTROL
57 * register. Then read it and make sure it's HERMES_AUX_ENABLED.
58 */
59 #define HERMES_AUX_ENABLE 0x8000 /* Enable auxiliary port access */
60 #define HERMES_AUX_DISABLE 0x4000 /* Disable to auxiliary port access */
61 #define HERMES_AUX_ENABLED 0xC000 /* Auxiliary port is open */
62 #define HERMES_AUX_DISABLED 0x0000 /* Auxiliary port is closed */
63
64 #define HERMES_AUX_PW0 0xFE01
65 #define HERMES_AUX_PW1 0xDC23
66 #define HERMES_AUX_PW2 0xBA45
67
68 /* HERMES_CMD_DOWNLD */
69 #define HERMES_PROGRAM_DISABLE (0x0000 | HERMES_CMD_DOWNLD)
70 #define HERMES_PROGRAM_ENABLE_VOLATILE (0x0100 | HERMES_CMD_DOWNLD)
71 #define HERMES_PROGRAM_ENABLE_NON_VOLATILE (0x0200 | HERMES_CMD_DOWNLD)
72 #define HERMES_PROGRAM_NON_VOLATILE (0x0300 | HERMES_CMD_DOWNLD)
73
74 /*
75 * Debugging helpers
76 */
77
78 #define DMSG(stuff...) do {printk(KERN_DEBUG "hermes @ %p: " , hw->iobase); \
79 printk(stuff); } while (0)
80
81 #undef HERMES_DEBUG
82 #ifdef HERMES_DEBUG
83
84 #define DEBUG(lvl, stuff...) if ((lvl) <= HERMES_DEBUG) DMSG(stuff)
85
86 #else /* ! HERMES_DEBUG */
87
88 #define DEBUG(lvl, stuff...) do { } while (0)
89
90 #endif /* ! HERMES_DEBUG */
91
92 static const struct hermes_ops hermes_ops_local;
93
94 /*
95 * Internal functions
96 */
97
98 /* Issue a command to the chip. Waiting for it to complete is the caller's
99 problem.
100
101 Returns -EBUSY if the command register is busy, 0 on success.
102
103 Callable from any context.
104 */
hermes_issue_cmd(struct hermes * hw,u16 cmd,u16 param0,u16 param1,u16 param2)105 static int hermes_issue_cmd(struct hermes *hw, u16 cmd, u16 param0,
106 u16 param1, u16 param2)
107 {
108 int k = CMD_BUSY_TIMEOUT;
109 u16 reg;
110
111 /* First wait for the command register to unbusy */
112 reg = hermes_read_regn(hw, CMD);
113 while ((reg & HERMES_CMD_BUSY) && k) {
114 k--;
115 udelay(1);
116 reg = hermes_read_regn(hw, CMD);
117 }
118 if (reg & HERMES_CMD_BUSY)
119 return -EBUSY;
120
121 hermes_write_regn(hw, PARAM2, param2);
122 hermes_write_regn(hw, PARAM1, param1);
123 hermes_write_regn(hw, PARAM0, param0);
124 hermes_write_regn(hw, CMD, cmd);
125
126 return 0;
127 }
128
129 /*
130 * Function definitions
131 */
132
133 /* For doing cmds that wipe the magic constant in SWSUPPORT0 */
hermes_doicmd_wait(struct hermes * hw,u16 cmd,u16 parm0,u16 parm1,u16 parm2,struct hermes_response * resp)134 static int hermes_doicmd_wait(struct hermes *hw, u16 cmd,
135 u16 parm0, u16 parm1, u16 parm2,
136 struct hermes_response *resp)
137 {
138 int err = 0;
139 int k;
140 u16 status, reg;
141
142 err = hermes_issue_cmd(hw, cmd, parm0, parm1, parm2);
143 if (err)
144 return err;
145
146 reg = hermes_read_regn(hw, EVSTAT);
147 k = CMD_INIT_TIMEOUT;
148 while ((!(reg & HERMES_EV_CMD)) && k) {
149 k--;
150 udelay(10);
151 reg = hermes_read_regn(hw, EVSTAT);
152 }
153
154 hermes_write_regn(hw, SWSUPPORT0, HERMES_MAGIC);
155
156 if (!hermes_present(hw)) {
157 DEBUG(0, "hermes @ 0x%x: Card removed during reset.\n",
158 hw->iobase);
159 err = -ENODEV;
160 goto out;
161 }
162
163 if (!(reg & HERMES_EV_CMD)) {
164 printk(KERN_ERR "hermes @ %p: "
165 "Timeout waiting for card to reset (reg=0x%04x)!\n",
166 hw->iobase, reg);
167 err = -ETIMEDOUT;
168 goto out;
169 }
170
171 status = hermes_read_regn(hw, STATUS);
172 if (resp) {
173 resp->status = status;
174 resp->resp0 = hermes_read_regn(hw, RESP0);
175 resp->resp1 = hermes_read_regn(hw, RESP1);
176 resp->resp2 = hermes_read_regn(hw, RESP2);
177 }
178
179 hermes_write_regn(hw, EVACK, HERMES_EV_CMD);
180
181 if (status & HERMES_STATUS_RESULT)
182 err = -EIO;
183 out:
184 return err;
185 }
186
hermes_struct_init(struct hermes * hw,void __iomem * address,int reg_spacing)187 void hermes_struct_init(struct hermes *hw, void __iomem *address,
188 int reg_spacing)
189 {
190 hw->iobase = address;
191 hw->reg_spacing = reg_spacing;
192 hw->inten = 0x0;
193 hw->eeprom_pda = false;
194 hw->ops = &hermes_ops_local;
195 }
196 EXPORT_SYMBOL(hermes_struct_init);
197
hermes_init(struct hermes * hw)198 static int hermes_init(struct hermes *hw)
199 {
200 u16 reg;
201 int err = 0;
202 int k;
203
204 /* We don't want to be interrupted while resetting the chipset */
205 hw->inten = 0x0;
206 hermes_write_regn(hw, INTEN, 0);
207 hermes_write_regn(hw, EVACK, 0xffff);
208
209 /* Normally it's a "can't happen" for the command register to
210 be busy when we go to issue a command because we are
211 serializing all commands. However we want to have some
212 chance of resetting the card even if it gets into a stupid
213 state, so we actually wait to see if the command register
214 will unbusy itself here. */
215 k = CMD_BUSY_TIMEOUT;
216 reg = hermes_read_regn(hw, CMD);
217 while (k && (reg & HERMES_CMD_BUSY)) {
218 if (reg == 0xffff) /* Special case - the card has probably been
219 removed, so don't wait for the timeout */
220 return -ENODEV;
221
222 k--;
223 udelay(1);
224 reg = hermes_read_regn(hw, CMD);
225 }
226
227 /* No need to explicitly handle the timeout - if we've timed
228 out hermes_issue_cmd() will probably return -EBUSY below */
229
230 /* According to the documentation, EVSTAT may contain
231 obsolete event occurrence information. We have to acknowledge
232 it by writing EVACK. */
233 reg = hermes_read_regn(hw, EVSTAT);
234 hermes_write_regn(hw, EVACK, reg);
235
236 /* We don't use hermes_docmd_wait here, because the reset wipes
237 the magic constant in SWSUPPORT0 away, and it gets confused */
238 err = hermes_doicmd_wait(hw, HERMES_CMD_INIT, 0, 0, 0, NULL);
239
240 return err;
241 }
242
243 /* Issue a command to the chip, and (busy!) wait for it to
244 * complete.
245 *
246 * Returns:
247 * < 0 on internal error
248 * 0 on success
249 * > 0 on error returned by the firmware
250 *
251 * Callable from any context, but locking is your problem. */
hermes_docmd_wait(struct hermes * hw,u16 cmd,u16 parm0,struct hermes_response * resp)252 static int hermes_docmd_wait(struct hermes *hw, u16 cmd, u16 parm0,
253 struct hermes_response *resp)
254 {
255 int err;
256 int k;
257 u16 reg;
258 u16 status;
259
260 err = hermes_issue_cmd(hw, cmd, parm0, 0, 0);
261 if (err) {
262 if (!hermes_present(hw)) {
263 if (net_ratelimit())
264 printk(KERN_WARNING "hermes @ %p: "
265 "Card removed while issuing command "
266 "0x%04x.\n", hw->iobase, cmd);
267 err = -ENODEV;
268 } else
269 if (net_ratelimit())
270 printk(KERN_ERR "hermes @ %p: "
271 "Error %d issuing command 0x%04x.\n",
272 hw->iobase, err, cmd);
273 goto out;
274 }
275
276 reg = hermes_read_regn(hw, EVSTAT);
277 k = CMD_COMPL_TIMEOUT;
278 while ((!(reg & HERMES_EV_CMD)) && k) {
279 k--;
280 udelay(10);
281 reg = hermes_read_regn(hw, EVSTAT);
282 }
283
284 if (!hermes_present(hw)) {
285 printk(KERN_WARNING "hermes @ %p: Card removed "
286 "while waiting for command 0x%04x completion.\n",
287 hw->iobase, cmd);
288 err = -ENODEV;
289 goto out;
290 }
291
292 if (!(reg & HERMES_EV_CMD)) {
293 printk(KERN_ERR "hermes @ %p: Timeout waiting for "
294 "command 0x%04x completion.\n", hw->iobase, cmd);
295 err = -ETIMEDOUT;
296 goto out;
297 }
298
299 status = hermes_read_regn(hw, STATUS);
300 if (resp) {
301 resp->status = status;
302 resp->resp0 = hermes_read_regn(hw, RESP0);
303 resp->resp1 = hermes_read_regn(hw, RESP1);
304 resp->resp2 = hermes_read_regn(hw, RESP2);
305 }
306
307 hermes_write_regn(hw, EVACK, HERMES_EV_CMD);
308
309 if (status & HERMES_STATUS_RESULT)
310 err = -EIO;
311
312 out:
313 return err;
314 }
315
hermes_allocate(struct hermes * hw,u16 size,u16 * fid)316 static int hermes_allocate(struct hermes *hw, u16 size, u16 *fid)
317 {
318 int err = 0;
319 int k;
320 u16 reg;
321
322 if ((size < HERMES_ALLOC_LEN_MIN) || (size > HERMES_ALLOC_LEN_MAX))
323 return -EINVAL;
324
325 err = hermes_docmd_wait(hw, HERMES_CMD_ALLOC, size, NULL);
326 if (err)
327 return err;
328
329 reg = hermes_read_regn(hw, EVSTAT);
330 k = ALLOC_COMPL_TIMEOUT;
331 while ((!(reg & HERMES_EV_ALLOC)) && k) {
332 k--;
333 udelay(10);
334 reg = hermes_read_regn(hw, EVSTAT);
335 }
336
337 if (!hermes_present(hw)) {
338 printk(KERN_WARNING "hermes @ %p: "
339 "Card removed waiting for frame allocation.\n",
340 hw->iobase);
341 return -ENODEV;
342 }
343
344 if (!(reg & HERMES_EV_ALLOC)) {
345 printk(KERN_ERR "hermes @ %p: "
346 "Timeout waiting for frame allocation\n",
347 hw->iobase);
348 return -ETIMEDOUT;
349 }
350
351 *fid = hermes_read_regn(hw, ALLOCFID);
352 hermes_write_regn(hw, EVACK, HERMES_EV_ALLOC);
353
354 return 0;
355 }
356
357 /* Set up a BAP to read a particular chunk of data from card's internal buffer.
358 *
359 * Returns:
360 * < 0 on internal failure (errno)
361 * 0 on success
362 * > 0 on error
363 * from firmware
364 *
365 * Callable from any context */
hermes_bap_seek(struct hermes * hw,int bap,u16 id,u16 offset)366 static int hermes_bap_seek(struct hermes *hw, int bap, u16 id, u16 offset)
367 {
368 int sreg = bap ? HERMES_SELECT1 : HERMES_SELECT0;
369 int oreg = bap ? HERMES_OFFSET1 : HERMES_OFFSET0;
370 int k;
371 u16 reg;
372
373 /* Paranoia.. */
374 if ((offset > HERMES_BAP_OFFSET_MAX) || (offset % 2))
375 return -EINVAL;
376
377 k = HERMES_BAP_BUSY_TIMEOUT;
378 reg = hermes_read_reg(hw, oreg);
379 while ((reg & HERMES_OFFSET_BUSY) && k) {
380 k--;
381 udelay(1);
382 reg = hermes_read_reg(hw, oreg);
383 }
384
385 if (reg & HERMES_OFFSET_BUSY)
386 return -ETIMEDOUT;
387
388 /* Now we actually set up the transfer */
389 hermes_write_reg(hw, sreg, id);
390 hermes_write_reg(hw, oreg, offset);
391
392 /* Wait for the BAP to be ready */
393 k = HERMES_BAP_BUSY_TIMEOUT;
394 reg = hermes_read_reg(hw, oreg);
395 while ((reg & (HERMES_OFFSET_BUSY | HERMES_OFFSET_ERR)) && k) {
396 k--;
397 udelay(1);
398 reg = hermes_read_reg(hw, oreg);
399 }
400
401 if (reg != offset) {
402 printk(KERN_ERR "hermes @ %p: BAP%d offset %s: "
403 "reg=0x%x id=0x%x offset=0x%x\n", hw->iobase, bap,
404 (reg & HERMES_OFFSET_BUSY) ? "timeout" : "error",
405 reg, id, offset);
406
407 if (reg & HERMES_OFFSET_BUSY)
408 return -ETIMEDOUT;
409
410 return -EIO; /* error or wrong offset */
411 }
412
413 return 0;
414 }
415
416 /* Read a block of data from the chip's buffer, via the
417 * BAP. Synchronization/serialization is the caller's problem. len
418 * must be even.
419 *
420 * Returns:
421 * < 0 on internal failure (errno)
422 * 0 on success
423 * > 0 on error from firmware
424 */
hermes_bap_pread(struct hermes * hw,int bap,void * buf,int len,u16 id,u16 offset)425 static int hermes_bap_pread(struct hermes *hw, int bap, void *buf, int len,
426 u16 id, u16 offset)
427 {
428 int dreg = bap ? HERMES_DATA1 : HERMES_DATA0;
429 int err = 0;
430
431 if ((len < 0) || (len % 2))
432 return -EINVAL;
433
434 err = hermes_bap_seek(hw, bap, id, offset);
435 if (err)
436 goto out;
437
438 /* Actually do the transfer */
439 hermes_read_words(hw, dreg, buf, len / 2);
440
441 out:
442 return err;
443 }
444
445 /* Write a block of data to the chip's buffer, via the
446 * BAP. Synchronization/serialization is the caller's problem.
447 *
448 * Returns:
449 * < 0 on internal failure (errno)
450 * 0 on success
451 * > 0 on error from firmware
452 */
hermes_bap_pwrite(struct hermes * hw,int bap,const void * buf,int len,u16 id,u16 offset)453 static int hermes_bap_pwrite(struct hermes *hw, int bap, const void *buf,
454 int len, u16 id, u16 offset)
455 {
456 int dreg = bap ? HERMES_DATA1 : HERMES_DATA0;
457 int err = 0;
458
459 if (len < 0)
460 return -EINVAL;
461
462 err = hermes_bap_seek(hw, bap, id, offset);
463 if (err)
464 goto out;
465
466 /* Actually do the transfer */
467 hermes_write_bytes(hw, dreg, buf, len);
468
469 out:
470 return err;
471 }
472
473 /* Read a Length-Type-Value record from the card.
474 *
475 * If length is NULL, we ignore the length read from the card, and
476 * read the entire buffer regardless. This is useful because some of
477 * the configuration records appear to have incorrect lengths in
478 * practice.
479 *
480 * Callable from user or bh context. */
hermes_read_ltv(struct hermes * hw,int bap,u16 rid,unsigned bufsize,u16 * length,void * buf)481 static int hermes_read_ltv(struct hermes *hw, int bap, u16 rid,
482 unsigned bufsize, u16 *length, void *buf)
483 {
484 int err = 0;
485 int dreg = bap ? HERMES_DATA1 : HERMES_DATA0;
486 u16 rlength, rtype;
487 unsigned nwords;
488
489 if (bufsize % 2)
490 return -EINVAL;
491
492 err = hermes_docmd_wait(hw, HERMES_CMD_ACCESS, rid, NULL);
493 if (err)
494 return err;
495
496 err = hermes_bap_seek(hw, bap, rid, 0);
497 if (err)
498 return err;
499
500 rlength = hermes_read_reg(hw, dreg);
501
502 if (!rlength)
503 return -ENODATA;
504
505 rtype = hermes_read_reg(hw, dreg);
506
507 if (length)
508 *length = rlength;
509
510 if (rtype != rid)
511 printk(KERN_WARNING "hermes @ %p: %s(): "
512 "rid (0x%04x) does not match type (0x%04x)\n",
513 hw->iobase, __func__, rid, rtype);
514 if (HERMES_RECLEN_TO_BYTES(rlength) > bufsize)
515 printk(KERN_WARNING "hermes @ %p: "
516 "Truncating LTV record from %d to %d bytes. "
517 "(rid=0x%04x, len=0x%04x)\n", hw->iobase,
518 HERMES_RECLEN_TO_BYTES(rlength), bufsize, rid, rlength);
519
520 nwords = min((unsigned)rlength - 1, bufsize / 2);
521 hermes_read_words(hw, dreg, buf, nwords);
522
523 return 0;
524 }
525
hermes_write_ltv(struct hermes * hw,int bap,u16 rid,u16 length,const void * value)526 static int hermes_write_ltv(struct hermes *hw, int bap, u16 rid,
527 u16 length, const void *value)
528 {
529 int dreg = bap ? HERMES_DATA1 : HERMES_DATA0;
530 int err = 0;
531 unsigned count;
532
533 if (length == 0)
534 return -EINVAL;
535
536 err = hermes_bap_seek(hw, bap, rid, 0);
537 if (err)
538 return err;
539
540 hermes_write_reg(hw, dreg, length);
541 hermes_write_reg(hw, dreg, rid);
542
543 count = length - 1;
544
545 hermes_write_bytes(hw, dreg, value, count << 1);
546
547 err = hermes_docmd_wait(hw, HERMES_CMD_ACCESS | HERMES_CMD_WRITE,
548 rid, NULL);
549
550 return err;
551 }
552
553 /*** Hermes AUX control ***/
554
555 static inline void
hermes_aux_setaddr(struct hermes * hw,u32 addr)556 hermes_aux_setaddr(struct hermes *hw, u32 addr)
557 {
558 hermes_write_reg(hw, HERMES_AUXPAGE, (u16) (addr >> 7));
559 hermes_write_reg(hw, HERMES_AUXOFFSET, (u16) (addr & 0x7F));
560 }
561
562 static inline int
hermes_aux_control(struct hermes * hw,int enabled)563 hermes_aux_control(struct hermes *hw, int enabled)
564 {
565 int desired_state = enabled ? HERMES_AUX_ENABLED : HERMES_AUX_DISABLED;
566 int action = enabled ? HERMES_AUX_ENABLE : HERMES_AUX_DISABLE;
567 int i;
568
569 /* Already open? */
570 if (hermes_read_reg(hw, HERMES_CONTROL) == desired_state)
571 return 0;
572
573 hermes_write_reg(hw, HERMES_PARAM0, HERMES_AUX_PW0);
574 hermes_write_reg(hw, HERMES_PARAM1, HERMES_AUX_PW1);
575 hermes_write_reg(hw, HERMES_PARAM2, HERMES_AUX_PW2);
576 hermes_write_reg(hw, HERMES_CONTROL, action);
577
578 for (i = 0; i < 20; i++) {
579 udelay(10);
580 if (hermes_read_reg(hw, HERMES_CONTROL) ==
581 desired_state)
582 return 0;
583 }
584
585 return -EBUSY;
586 }
587
588 /*** Hermes programming ***/
589
590 /* About to start programming data (Hermes I)
591 * offset is the entry point
592 *
593 * Spectrum_cs' Symbol fw does not require this
594 * wl_lkm Agere fw does
595 * Don't know about intersil
596 */
hermesi_program_init(struct hermes * hw,u32 offset)597 static int hermesi_program_init(struct hermes *hw, u32 offset)
598 {
599 int err;
600
601 /* Disable interrupts?*/
602 /*hw->inten = 0x0;*/
603 /*hermes_write_regn(hw, INTEN, 0);*/
604 /*hermes_set_irqmask(hw, 0);*/
605
606 /* Acknowledge any outstanding command */
607 hermes_write_regn(hw, EVACK, 0xFFFF);
608
609 /* Using init_cmd_wait rather than cmd_wait */
610 err = hw->ops->init_cmd_wait(hw,
611 0x0100 | HERMES_CMD_INIT,
612 0, 0, 0, NULL);
613 if (err)
614 return err;
615
616 err = hw->ops->init_cmd_wait(hw,
617 0x0000 | HERMES_CMD_INIT,
618 0, 0, 0, NULL);
619 if (err)
620 return err;
621
622 err = hermes_aux_control(hw, 1);
623 pr_debug("AUX enable returned %d\n", err);
624
625 if (err)
626 return err;
627
628 pr_debug("Enabling volatile, EP 0x%08x\n", offset);
629 err = hw->ops->init_cmd_wait(hw,
630 HERMES_PROGRAM_ENABLE_VOLATILE,
631 offset & 0xFFFFu,
632 offset >> 16,
633 0,
634 NULL);
635 pr_debug("PROGRAM_ENABLE returned %d\n", err);
636
637 return err;
638 }
639
640 /* Done programming data (Hermes I)
641 *
642 * Spectrum_cs' Symbol fw does not require this
643 * wl_lkm Agere fw does
644 * Don't know about intersil
645 */
hermesi_program_end(struct hermes * hw)646 static int hermesi_program_end(struct hermes *hw)
647 {
648 struct hermes_response resp;
649 int rc = 0;
650 int err;
651
652 rc = hw->ops->cmd_wait(hw, HERMES_PROGRAM_DISABLE, 0, &resp);
653
654 pr_debug("PROGRAM_DISABLE returned %d, "
655 "r0 0x%04x, r1 0x%04x, r2 0x%04x\n",
656 rc, resp.resp0, resp.resp1, resp.resp2);
657
658 if ((rc == 0) &&
659 ((resp.status & HERMES_STATUS_CMDCODE) != HERMES_CMD_DOWNLD))
660 rc = -EIO;
661
662 err = hermes_aux_control(hw, 0);
663 pr_debug("AUX disable returned %d\n", err);
664
665 /* Acknowledge any outstanding command */
666 hermes_write_regn(hw, EVACK, 0xFFFF);
667
668 /* Reinitialise, ignoring return */
669 (void) hw->ops->init_cmd_wait(hw, 0x0000 | HERMES_CMD_INIT,
670 0, 0, 0, NULL);
671
672 return rc ? rc : err;
673 }
674
hermes_program_bytes(struct hermes * hw,const char * data,u32 addr,u32 len)675 static int hermes_program_bytes(struct hermes *hw, const char *data,
676 u32 addr, u32 len)
677 {
678 /* wl lkm splits the programming into chunks of 2000 bytes.
679 * This restriction appears to come from USB. The PCMCIA
680 * adapters can program the whole lot in one go */
681 hermes_aux_setaddr(hw, addr);
682 hermes_write_bytes(hw, HERMES_AUXDATA, data, len);
683 return 0;
684 }
685
686 /* Read PDA from the adapter */
hermes_read_pda(struct hermes * hw,__le16 * pda,u32 pda_addr,u16 pda_len)687 static int hermes_read_pda(struct hermes *hw, __le16 *pda, u32 pda_addr,
688 u16 pda_len)
689 {
690 int ret;
691 u16 pda_size;
692 u16 data_len = pda_len;
693 __le16 *data = pda;
694
695 if (hw->eeprom_pda) {
696 /* PDA of spectrum symbol is in eeprom */
697
698 /* Issue command to read EEPROM */
699 ret = hw->ops->cmd_wait(hw, HERMES_CMD_READMIF, 0, NULL);
700 if (ret)
701 return ret;
702 } else {
703 /* wl_lkm does not include PDA size in the PDA area.
704 * We will pad the information into pda, so other routines
705 * don't have to be modified */
706 pda[0] = cpu_to_le16(pda_len - 2);
707 /* Includes CFG_PROD_DATA but not itself */
708 pda[1] = cpu_to_le16(0x0800); /* CFG_PROD_DATA */
709 data_len = pda_len - 4;
710 data = pda + 2;
711 }
712
713 /* Open auxiliary port */
714 ret = hermes_aux_control(hw, 1);
715 pr_debug("AUX enable returned %d\n", ret);
716 if (ret)
717 return ret;
718
719 /* Read PDA */
720 hermes_aux_setaddr(hw, pda_addr);
721 hermes_read_words(hw, HERMES_AUXDATA, data, data_len / 2);
722
723 /* Close aux port */
724 ret = hermes_aux_control(hw, 0);
725 pr_debug("AUX disable returned %d\n", ret);
726
727 /* Check PDA length */
728 pda_size = le16_to_cpu(pda[0]);
729 pr_debug("Actual PDA length %d, Max allowed %d\n",
730 pda_size, pda_len);
731 if (pda_size > pda_len)
732 return -EINVAL;
733
734 return 0;
735 }
736
hermes_lock_irqsave(spinlock_t * lock,unsigned long * flags)737 static void hermes_lock_irqsave(spinlock_t *lock,
738 unsigned long *flags) __acquires(lock)
739 {
740 spin_lock_irqsave(lock, *flags);
741 }
742
hermes_unlock_irqrestore(spinlock_t * lock,unsigned long * flags)743 static void hermes_unlock_irqrestore(spinlock_t *lock,
744 unsigned long *flags) __releases(lock)
745 {
746 spin_unlock_irqrestore(lock, *flags);
747 }
748
hermes_lock_irq(spinlock_t * lock)749 static void hermes_lock_irq(spinlock_t *lock) __acquires(lock)
750 {
751 spin_lock_irq(lock);
752 }
753
hermes_unlock_irq(spinlock_t * lock)754 static void hermes_unlock_irq(spinlock_t *lock) __releases(lock)
755 {
756 spin_unlock_irq(lock);
757 }
758
759 /* Hermes operations for local buses */
760 static const struct hermes_ops hermes_ops_local = {
761 .init = hermes_init,
762 .cmd_wait = hermes_docmd_wait,
763 .init_cmd_wait = hermes_doicmd_wait,
764 .allocate = hermes_allocate,
765 .read_ltv = hermes_read_ltv,
766 .read_ltv_pr = hermes_read_ltv,
767 .write_ltv = hermes_write_ltv,
768 .bap_pread = hermes_bap_pread,
769 .bap_pwrite = hermes_bap_pwrite,
770 .read_pda = hermes_read_pda,
771 .program_init = hermesi_program_init,
772 .program_end = hermesi_program_end,
773 .program = hermes_program_bytes,
774 .lock_irqsave = hermes_lock_irqsave,
775 .unlock_irqrestore = hermes_unlock_irqrestore,
776 .lock_irq = hermes_lock_irq,
777 .unlock_irq = hermes_unlock_irq,
778 };
779