1 /*
2 * SPDX-License-Identifier: GPL-2.0
3 * Copyright (c) 2018, The Linux Foundation
4 */
5
6 #include <linux/clk.h>
7 #include <linux/clk-provider.h>
8 #include <linux/iopoll.h>
9
10 #include "dsi_phy.h"
11 #include "dsi.xml.h"
12 #include "dsi_phy_10nm.xml.h"
13
14 /*
15 * DSI PLL 10nm - clock diagram (eg: DSI0):
16 *
17 * dsi0_pll_out_div_clk dsi0_pll_bit_clk
18 * | |
19 * | |
20 * +---------+ | +----------+ | +----+
21 * dsi0vco_clk ---| out_div |--o--| divl_3_0 |--o--| /8 |-- dsi0_phy_pll_out_byteclk
22 * +---------+ | +----------+ | +----+
23 * | |
24 * | | dsi0_pll_by_2_bit_clk
25 * | | |
26 * | | +----+ | |\ dsi0_pclk_mux
27 * | |--| /2 |--o--| \ |
28 * | | +----+ | \ | +---------+
29 * | --------------| |--o--| div_7_4 |-- dsi0_phy_pll_out_dsiclk
30 * |------------------------------| / +---------+
31 * | +-----+ | /
32 * -----------| /4? |--o----------|/
33 * +-----+ | |
34 * | |dsiclk_sel
35 * |
36 * dsi0_pll_post_out_div_clk
37 */
38
39 #define VCO_REF_CLK_RATE 19200000
40 #define FRAC_BITS 18
41
42 /* v3.0.0 10nm implementation that requires the old timings settings */
43 #define DSI_PHY_10NM_QUIRK_OLD_TIMINGS BIT(0)
44
45 struct dsi_pll_config {
46 bool enable_ssc;
47 bool ssc_center;
48 u32 ssc_freq;
49 u32 ssc_offset;
50 u32 ssc_adj_per;
51
52 /* out */
53 u32 pll_prop_gain_rate;
54 u32 decimal_div_start;
55 u32 frac_div_start;
56 u32 pll_clock_inverters;
57 u32 ssc_stepsize;
58 u32 ssc_div_per;
59 };
60
61 struct pll_10nm_cached_state {
62 unsigned long vco_rate;
63 u8 bit_clk_div;
64 u8 pix_clk_div;
65 u8 pll_out_div;
66 u8 pll_mux;
67 };
68
69 struct dsi_pll_10nm {
70 struct clk_hw clk_hw;
71
72 struct msm_dsi_phy *phy;
73
74 u64 vco_current_rate;
75
76 /* protects REG_DSI_10nm_PHY_CMN_CLK_CFG0 register */
77 spinlock_t postdiv_lock;
78
79 struct pll_10nm_cached_state cached_state;
80
81 struct dsi_pll_10nm *slave;
82 };
83
84 #define to_pll_10nm(x) container_of(x, struct dsi_pll_10nm, clk_hw)
85
86 /**
87 * struct dsi_phy_10nm_tuning_cfg - Holds 10nm PHY tuning config parameters.
88 * @rescode_offset_top: Offset for pull-up legs rescode.
89 * @rescode_offset_bot: Offset for pull-down legs rescode.
90 * @vreg_ctrl: vreg ctrl to drive LDO level
91 */
92 struct dsi_phy_10nm_tuning_cfg {
93 u8 rescode_offset_top[DSI_LANE_MAX];
94 u8 rescode_offset_bot[DSI_LANE_MAX];
95 u8 vreg_ctrl;
96 };
97
98 /*
99 * Global list of private DSI PLL struct pointers. We need this for bonded DSI
100 * mode, where the master PLL's clk_ops needs access the slave's private data
101 */
102 static struct dsi_pll_10nm *pll_10nm_list[DSI_MAX];
103
dsi_pll_setup_config(struct dsi_pll_config * config)104 static void dsi_pll_setup_config(struct dsi_pll_config *config)
105 {
106 config->ssc_freq = 31500;
107 config->ssc_offset = 5000;
108 config->ssc_adj_per = 2;
109
110 config->enable_ssc = false;
111 config->ssc_center = false;
112 }
113
dsi_pll_calc_dec_frac(struct dsi_pll_10nm * pll,struct dsi_pll_config * config)114 static void dsi_pll_calc_dec_frac(struct dsi_pll_10nm *pll, struct dsi_pll_config *config)
115 {
116 u64 fref = VCO_REF_CLK_RATE;
117 u64 pll_freq;
118 u64 divider;
119 u64 dec, dec_multiple;
120 u32 frac;
121 u64 multiplier;
122
123 pll_freq = pll->vco_current_rate;
124
125 divider = fref * 2;
126
127 multiplier = 1 << FRAC_BITS;
128 dec_multiple = div_u64(pll_freq * multiplier, divider);
129 dec = div_u64_rem(dec_multiple, multiplier, &frac);
130
131 if (pll_freq <= 1900000000UL)
132 config->pll_prop_gain_rate = 8;
133 else if (pll_freq <= 3000000000UL)
134 config->pll_prop_gain_rate = 10;
135 else
136 config->pll_prop_gain_rate = 12;
137 if (pll_freq < 1100000000UL)
138 config->pll_clock_inverters = 8;
139 else
140 config->pll_clock_inverters = 0;
141
142 config->decimal_div_start = dec;
143 config->frac_div_start = frac;
144 }
145
146 #define SSC_CENTER BIT(0)
147 #define SSC_EN BIT(1)
148
dsi_pll_calc_ssc(struct dsi_pll_10nm * pll,struct dsi_pll_config * config)149 static void dsi_pll_calc_ssc(struct dsi_pll_10nm *pll, struct dsi_pll_config *config)
150 {
151 u32 ssc_per;
152 u32 ssc_mod;
153 u64 ssc_step_size;
154 u64 frac;
155
156 if (!config->enable_ssc) {
157 DBG("SSC not enabled\n");
158 return;
159 }
160
161 ssc_per = DIV_ROUND_CLOSEST(VCO_REF_CLK_RATE, config->ssc_freq) / 2 - 1;
162 ssc_mod = (ssc_per + 1) % (config->ssc_adj_per + 1);
163 ssc_per -= ssc_mod;
164
165 frac = config->frac_div_start;
166 ssc_step_size = config->decimal_div_start;
167 ssc_step_size *= (1 << FRAC_BITS);
168 ssc_step_size += frac;
169 ssc_step_size *= config->ssc_offset;
170 ssc_step_size *= (config->ssc_adj_per + 1);
171 ssc_step_size = div_u64(ssc_step_size, (ssc_per + 1));
172 ssc_step_size = DIV_ROUND_CLOSEST_ULL(ssc_step_size, 1000000);
173
174 config->ssc_div_per = ssc_per;
175 config->ssc_stepsize = ssc_step_size;
176
177 pr_debug("SCC: Dec:%d, frac:%llu, frac_bits:%d\n",
178 config->decimal_div_start, frac, FRAC_BITS);
179 pr_debug("SSC: div_per:0x%X, stepsize:0x%X, adjper:0x%X\n",
180 ssc_per, (u32)ssc_step_size, config->ssc_adj_per);
181 }
182
dsi_pll_ssc_commit(struct dsi_pll_10nm * pll,struct dsi_pll_config * config)183 static void dsi_pll_ssc_commit(struct dsi_pll_10nm *pll, struct dsi_pll_config *config)
184 {
185 void __iomem *base = pll->phy->pll_base;
186
187 if (config->enable_ssc) {
188 pr_debug("SSC is enabled\n");
189
190 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_SSC_STEPSIZE_LOW_1,
191 config->ssc_stepsize & 0xff);
192 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_SSC_STEPSIZE_HIGH_1,
193 config->ssc_stepsize >> 8);
194 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_SSC_DIV_PER_LOW_1,
195 config->ssc_div_per & 0xff);
196 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_SSC_DIV_PER_HIGH_1,
197 config->ssc_div_per >> 8);
198 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_SSC_DIV_ADJPER_LOW_1,
199 config->ssc_adj_per & 0xff);
200 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_SSC_DIV_ADJPER_HIGH_1,
201 config->ssc_adj_per >> 8);
202 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_SSC_CONTROL,
203 SSC_EN | (config->ssc_center ? SSC_CENTER : 0));
204 }
205 }
206
dsi_pll_config_hzindep_reg(struct dsi_pll_10nm * pll)207 static void dsi_pll_config_hzindep_reg(struct dsi_pll_10nm *pll)
208 {
209 void __iomem *base = pll->phy->pll_base;
210
211 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_ANALOG_CONTROLS_ONE, 0x80);
212 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_ANALOG_CONTROLS_TWO, 0x03);
213 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_ANALOG_CONTROLS_THREE, 0x00);
214 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_DSM_DIVIDER, 0x00);
215 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_FEEDBACK_DIVIDER, 0x4e);
216 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_CALIBRATION_SETTINGS, 0x40);
217 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_BAND_SEL_CAL_SETTINGS_THREE,
218 0xba);
219 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_FREQ_DETECT_SETTINGS_ONE,
220 0x0c);
221 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_OUTDIV, 0x00);
222 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_CORE_OVERRIDE, 0x00);
223 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_PLL_DIGITAL_TIMERS_TWO,
224 0x08);
225 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_PLL_PROP_GAIN_RATE_1, 0x08);
226 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_PLL_BAND_SET_RATE_1, 0xc0);
227 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_PLL_INT_GAIN_IFILT_BAND_1,
228 0xfa);
229 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_PLL_FL_INT_GAIN_PFILT_BAND_1,
230 0x4c);
231 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_PLL_LOCK_OVERRIDE, 0x80);
232 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_PFILT, 0x29);
233 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_IFILT, 0x3f);
234 }
235
dsi_pll_commit(struct dsi_pll_10nm * pll,struct dsi_pll_config * config)236 static void dsi_pll_commit(struct dsi_pll_10nm *pll, struct dsi_pll_config *config)
237 {
238 void __iomem *base = pll->phy->pll_base;
239
240 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_CORE_INPUT_OVERRIDE, 0x12);
241 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_DECIMAL_DIV_START_1,
242 config->decimal_div_start);
243 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_FRAC_DIV_START_LOW_1,
244 config->frac_div_start & 0xff);
245 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_FRAC_DIV_START_MID_1,
246 (config->frac_div_start & 0xff00) >> 8);
247 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_FRAC_DIV_START_HIGH_1,
248 (config->frac_div_start & 0x30000) >> 16);
249 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_PLL_LOCKDET_RATE_1, 64);
250 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_PLL_LOCK_DELAY, 0x06);
251 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_CMODE, 0x10);
252 dsi_phy_write(base + REG_DSI_10nm_PHY_PLL_CLOCK_INVERTERS,
253 config->pll_clock_inverters);
254 }
255
dsi_pll_10nm_vco_set_rate(struct clk_hw * hw,unsigned long rate,unsigned long parent_rate)256 static int dsi_pll_10nm_vco_set_rate(struct clk_hw *hw, unsigned long rate,
257 unsigned long parent_rate)
258 {
259 struct dsi_pll_10nm *pll_10nm = to_pll_10nm(hw);
260 struct dsi_pll_config config;
261
262 DBG("DSI PLL%d rate=%lu, parent's=%lu", pll_10nm->phy->id, rate,
263 parent_rate);
264
265 pll_10nm->vco_current_rate = rate;
266
267 dsi_pll_setup_config(&config);
268
269 dsi_pll_calc_dec_frac(pll_10nm, &config);
270
271 dsi_pll_calc_ssc(pll_10nm, &config);
272
273 dsi_pll_commit(pll_10nm, &config);
274
275 dsi_pll_config_hzindep_reg(pll_10nm);
276
277 dsi_pll_ssc_commit(pll_10nm, &config);
278
279 /* flush, ensure all register writes are done*/
280 wmb();
281
282 return 0;
283 }
284
dsi_pll_10nm_lock_status(struct dsi_pll_10nm * pll)285 static int dsi_pll_10nm_lock_status(struct dsi_pll_10nm *pll)
286 {
287 struct device *dev = &pll->phy->pdev->dev;
288 int rc;
289 u32 status = 0;
290 u32 const delay_us = 100;
291 u32 const timeout_us = 5000;
292
293 rc = readl_poll_timeout_atomic(pll->phy->pll_base +
294 REG_DSI_10nm_PHY_PLL_COMMON_STATUS_ONE,
295 status,
296 ((status & BIT(0)) > 0),
297 delay_us,
298 timeout_us);
299 if (rc)
300 DRM_DEV_ERROR(dev, "DSI PLL(%d) lock failed, status=0x%08x\n",
301 pll->phy->id, status);
302
303 return rc;
304 }
305
dsi_pll_disable_pll_bias(struct dsi_pll_10nm * pll)306 static void dsi_pll_disable_pll_bias(struct dsi_pll_10nm *pll)
307 {
308 u32 data = dsi_phy_read(pll->phy->base + REG_DSI_10nm_PHY_CMN_CTRL_0);
309
310 dsi_phy_write(pll->phy->pll_base + REG_DSI_10nm_PHY_PLL_SYSTEM_MUXES, 0);
311 dsi_phy_write(pll->phy->base + REG_DSI_10nm_PHY_CMN_CTRL_0,
312 data & ~BIT(5));
313 ndelay(250);
314 }
315
dsi_pll_enable_pll_bias(struct dsi_pll_10nm * pll)316 static void dsi_pll_enable_pll_bias(struct dsi_pll_10nm *pll)
317 {
318 u32 data = dsi_phy_read(pll->phy->base + REG_DSI_10nm_PHY_CMN_CTRL_0);
319
320 dsi_phy_write(pll->phy->base + REG_DSI_10nm_PHY_CMN_CTRL_0,
321 data | BIT(5));
322 dsi_phy_write(pll->phy->pll_base + REG_DSI_10nm_PHY_PLL_SYSTEM_MUXES, 0xc0);
323 ndelay(250);
324 }
325
dsi_pll_disable_global_clk(struct dsi_pll_10nm * pll)326 static void dsi_pll_disable_global_clk(struct dsi_pll_10nm *pll)
327 {
328 u32 data;
329
330 data = dsi_phy_read(pll->phy->base + REG_DSI_10nm_PHY_CMN_CLK_CFG1);
331 dsi_phy_write(pll->phy->base + REG_DSI_10nm_PHY_CMN_CLK_CFG1,
332 data & ~BIT(5));
333 }
334
dsi_pll_enable_global_clk(struct dsi_pll_10nm * pll)335 static void dsi_pll_enable_global_clk(struct dsi_pll_10nm *pll)
336 {
337 u32 data;
338
339 data = dsi_phy_read(pll->phy->base + REG_DSI_10nm_PHY_CMN_CLK_CFG1);
340 dsi_phy_write(pll->phy->base + REG_DSI_10nm_PHY_CMN_CLK_CFG1,
341 data | BIT(5));
342 }
343
dsi_pll_10nm_vco_prepare(struct clk_hw * hw)344 static int dsi_pll_10nm_vco_prepare(struct clk_hw *hw)
345 {
346 struct dsi_pll_10nm *pll_10nm = to_pll_10nm(hw);
347 struct device *dev = &pll_10nm->phy->pdev->dev;
348 int rc;
349
350 dsi_pll_enable_pll_bias(pll_10nm);
351 if (pll_10nm->slave)
352 dsi_pll_enable_pll_bias(pll_10nm->slave);
353
354 rc = dsi_pll_10nm_vco_set_rate(hw,pll_10nm->vco_current_rate, 0);
355 if (rc) {
356 DRM_DEV_ERROR(dev, "vco_set_rate failed, rc=%d\n", rc);
357 return rc;
358 }
359
360 /* Start PLL */
361 dsi_phy_write(pll_10nm->phy->base + REG_DSI_10nm_PHY_CMN_PLL_CNTRL,
362 0x01);
363
364 /*
365 * ensure all PLL configurations are written prior to checking
366 * for PLL lock.
367 */
368 wmb();
369
370 /* Check for PLL lock */
371 rc = dsi_pll_10nm_lock_status(pll_10nm);
372 if (rc) {
373 DRM_DEV_ERROR(dev, "PLL(%d) lock failed\n", pll_10nm->phy->id);
374 goto error;
375 }
376
377 pll_10nm->phy->pll_on = true;
378
379 dsi_pll_enable_global_clk(pll_10nm);
380 if (pll_10nm->slave)
381 dsi_pll_enable_global_clk(pll_10nm->slave);
382
383 dsi_phy_write(pll_10nm->phy->base + REG_DSI_10nm_PHY_CMN_RBUF_CTRL,
384 0x01);
385 if (pll_10nm->slave)
386 dsi_phy_write(pll_10nm->slave->phy->base +
387 REG_DSI_10nm_PHY_CMN_RBUF_CTRL, 0x01);
388
389 error:
390 return rc;
391 }
392
dsi_pll_disable_sub(struct dsi_pll_10nm * pll)393 static void dsi_pll_disable_sub(struct dsi_pll_10nm *pll)
394 {
395 dsi_phy_write(pll->phy->base + REG_DSI_10nm_PHY_CMN_RBUF_CTRL, 0);
396 dsi_pll_disable_pll_bias(pll);
397 }
398
dsi_pll_10nm_vco_unprepare(struct clk_hw * hw)399 static void dsi_pll_10nm_vco_unprepare(struct clk_hw *hw)
400 {
401 struct dsi_pll_10nm *pll_10nm = to_pll_10nm(hw);
402
403 /*
404 * To avoid any stray glitches while abruptly powering down the PLL
405 * make sure to gate the clock using the clock enable bit before
406 * powering down the PLL
407 */
408 dsi_pll_disable_global_clk(pll_10nm);
409 dsi_phy_write(pll_10nm->phy->base + REG_DSI_10nm_PHY_CMN_PLL_CNTRL, 0);
410 dsi_pll_disable_sub(pll_10nm);
411 if (pll_10nm->slave) {
412 dsi_pll_disable_global_clk(pll_10nm->slave);
413 dsi_pll_disable_sub(pll_10nm->slave);
414 }
415 /* flush, ensure all register writes are done */
416 wmb();
417 pll_10nm->phy->pll_on = false;
418 }
419
dsi_pll_10nm_vco_recalc_rate(struct clk_hw * hw,unsigned long parent_rate)420 static unsigned long dsi_pll_10nm_vco_recalc_rate(struct clk_hw *hw,
421 unsigned long parent_rate)
422 {
423 struct dsi_pll_10nm *pll_10nm = to_pll_10nm(hw);
424 void __iomem *base = pll_10nm->phy->pll_base;
425 u64 ref_clk = VCO_REF_CLK_RATE;
426 u64 vco_rate = 0x0;
427 u64 multiplier;
428 u32 frac;
429 u32 dec;
430 u64 pll_freq, tmp64;
431
432 dec = dsi_phy_read(base + REG_DSI_10nm_PHY_PLL_DECIMAL_DIV_START_1);
433 dec &= 0xff;
434
435 frac = dsi_phy_read(base + REG_DSI_10nm_PHY_PLL_FRAC_DIV_START_LOW_1);
436 frac |= ((dsi_phy_read(base + REG_DSI_10nm_PHY_PLL_FRAC_DIV_START_MID_1) &
437 0xff) << 8);
438 frac |= ((dsi_phy_read(base + REG_DSI_10nm_PHY_PLL_FRAC_DIV_START_HIGH_1) &
439 0x3) << 16);
440
441 /*
442 * TODO:
443 * 1. Assumes prescaler is disabled
444 */
445 multiplier = 1 << FRAC_BITS;
446 pll_freq = dec * (ref_clk * 2);
447 tmp64 = (ref_clk * 2 * frac);
448 pll_freq += div_u64(tmp64, multiplier);
449
450 vco_rate = pll_freq;
451 pll_10nm->vco_current_rate = vco_rate;
452
453 DBG("DSI PLL%d returning vco rate = %lu, dec = %x, frac = %x",
454 pll_10nm->phy->id, (unsigned long)vco_rate, dec, frac);
455
456 return (unsigned long)vco_rate;
457 }
458
dsi_pll_10nm_clk_round_rate(struct clk_hw * hw,unsigned long rate,unsigned long * parent_rate)459 static long dsi_pll_10nm_clk_round_rate(struct clk_hw *hw,
460 unsigned long rate, unsigned long *parent_rate)
461 {
462 struct dsi_pll_10nm *pll_10nm = to_pll_10nm(hw);
463
464 if (rate < pll_10nm->phy->cfg->min_pll_rate)
465 return pll_10nm->phy->cfg->min_pll_rate;
466 else if (rate > pll_10nm->phy->cfg->max_pll_rate)
467 return pll_10nm->phy->cfg->max_pll_rate;
468 else
469 return rate;
470 }
471
472 static const struct clk_ops clk_ops_dsi_pll_10nm_vco = {
473 .round_rate = dsi_pll_10nm_clk_round_rate,
474 .set_rate = dsi_pll_10nm_vco_set_rate,
475 .recalc_rate = dsi_pll_10nm_vco_recalc_rate,
476 .prepare = dsi_pll_10nm_vco_prepare,
477 .unprepare = dsi_pll_10nm_vco_unprepare,
478 };
479
480 /*
481 * PLL Callbacks
482 */
483
dsi_10nm_pll_save_state(struct msm_dsi_phy * phy)484 static void dsi_10nm_pll_save_state(struct msm_dsi_phy *phy)
485 {
486 struct dsi_pll_10nm *pll_10nm = to_pll_10nm(phy->vco_hw);
487 struct pll_10nm_cached_state *cached = &pll_10nm->cached_state;
488 void __iomem *phy_base = pll_10nm->phy->base;
489 u32 cmn_clk_cfg0, cmn_clk_cfg1;
490
491 cached->pll_out_div = dsi_phy_read(pll_10nm->phy->pll_base +
492 REG_DSI_10nm_PHY_PLL_PLL_OUTDIV_RATE);
493 cached->pll_out_div &= 0x3;
494
495 cmn_clk_cfg0 = dsi_phy_read(phy_base + REG_DSI_10nm_PHY_CMN_CLK_CFG0);
496 cached->bit_clk_div = cmn_clk_cfg0 & 0xf;
497 cached->pix_clk_div = (cmn_clk_cfg0 & 0xf0) >> 4;
498
499 cmn_clk_cfg1 = dsi_phy_read(phy_base + REG_DSI_10nm_PHY_CMN_CLK_CFG1);
500 cached->pll_mux = cmn_clk_cfg1 & 0x3;
501
502 DBG("DSI PLL%d outdiv %x bit_clk_div %x pix_clk_div %x pll_mux %x",
503 pll_10nm->phy->id, cached->pll_out_div, cached->bit_clk_div,
504 cached->pix_clk_div, cached->pll_mux);
505 }
506
dsi_10nm_pll_restore_state(struct msm_dsi_phy * phy)507 static int dsi_10nm_pll_restore_state(struct msm_dsi_phy *phy)
508 {
509 struct dsi_pll_10nm *pll_10nm = to_pll_10nm(phy->vco_hw);
510 struct pll_10nm_cached_state *cached = &pll_10nm->cached_state;
511 void __iomem *phy_base = pll_10nm->phy->base;
512 u32 val;
513 int ret;
514
515 val = dsi_phy_read(pll_10nm->phy->pll_base + REG_DSI_10nm_PHY_PLL_PLL_OUTDIV_RATE);
516 val &= ~0x3;
517 val |= cached->pll_out_div;
518 dsi_phy_write(pll_10nm->phy->pll_base + REG_DSI_10nm_PHY_PLL_PLL_OUTDIV_RATE, val);
519
520 dsi_phy_write(phy_base + REG_DSI_10nm_PHY_CMN_CLK_CFG0,
521 cached->bit_clk_div | (cached->pix_clk_div << 4));
522
523 val = dsi_phy_read(phy_base + REG_DSI_10nm_PHY_CMN_CLK_CFG1);
524 val &= ~0x3;
525 val |= cached->pll_mux;
526 dsi_phy_write(phy_base + REG_DSI_10nm_PHY_CMN_CLK_CFG1, val);
527
528 ret = dsi_pll_10nm_vco_set_rate(phy->vco_hw,
529 pll_10nm->vco_current_rate,
530 VCO_REF_CLK_RATE);
531 if (ret) {
532 DRM_DEV_ERROR(&pll_10nm->phy->pdev->dev,
533 "restore vco rate failed. ret=%d\n", ret);
534 return ret;
535 }
536
537 DBG("DSI PLL%d", pll_10nm->phy->id);
538
539 return 0;
540 }
541
dsi_10nm_set_usecase(struct msm_dsi_phy * phy)542 static int dsi_10nm_set_usecase(struct msm_dsi_phy *phy)
543 {
544 struct dsi_pll_10nm *pll_10nm = to_pll_10nm(phy->vco_hw);
545 void __iomem *base = phy->base;
546 u32 data = 0x0; /* internal PLL */
547
548 DBG("DSI PLL%d", pll_10nm->phy->id);
549
550 switch (phy->usecase) {
551 case MSM_DSI_PHY_STANDALONE:
552 break;
553 case MSM_DSI_PHY_MASTER:
554 pll_10nm->slave = pll_10nm_list[(pll_10nm->phy->id + 1) % DSI_MAX];
555 break;
556 case MSM_DSI_PHY_SLAVE:
557 data = 0x1; /* external PLL */
558 break;
559 default:
560 return -EINVAL;
561 }
562
563 /* set PLL src */
564 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_CLK_CFG1, (data << 2));
565
566 return 0;
567 }
568
569 /*
570 * The post dividers and mux clocks are created using the standard divider and
571 * mux API. Unlike the 14nm PHY, the slave PLL doesn't need its dividers/mux
572 * state to follow the master PLL's divider/mux state. Therefore, we don't
573 * require special clock ops that also configure the slave PLL registers
574 */
pll_10nm_register(struct dsi_pll_10nm * pll_10nm,struct clk_hw ** provided_clocks)575 static int pll_10nm_register(struct dsi_pll_10nm *pll_10nm, struct clk_hw **provided_clocks)
576 {
577 char clk_name[32];
578 struct clk_init_data vco_init = {
579 .parent_data = &(const struct clk_parent_data) {
580 .fw_name = "ref",
581 },
582 .num_parents = 1,
583 .name = clk_name,
584 .flags = CLK_IGNORE_UNUSED,
585 .ops = &clk_ops_dsi_pll_10nm_vco,
586 };
587 struct device *dev = &pll_10nm->phy->pdev->dev;
588 struct clk_hw *hw, *pll_out_div, *pll_bit, *pll_by_2_bit;
589 struct clk_hw *pll_post_out_div, *pclk_mux;
590 int ret;
591
592 DBG("DSI%d", pll_10nm->phy->id);
593
594 snprintf(clk_name, sizeof(clk_name), "dsi%dvco_clk", pll_10nm->phy->id);
595 pll_10nm->clk_hw.init = &vco_init;
596
597 ret = devm_clk_hw_register(dev, &pll_10nm->clk_hw);
598 if (ret)
599 return ret;
600
601 snprintf(clk_name, sizeof(clk_name), "dsi%d_pll_out_div_clk", pll_10nm->phy->id);
602
603 pll_out_div = devm_clk_hw_register_divider_parent_hw(dev, clk_name,
604 &pll_10nm->clk_hw, CLK_SET_RATE_PARENT,
605 pll_10nm->phy->pll_base +
606 REG_DSI_10nm_PHY_PLL_PLL_OUTDIV_RATE,
607 0, 2, CLK_DIVIDER_POWER_OF_TWO, NULL);
608 if (IS_ERR(pll_out_div)) {
609 ret = PTR_ERR(pll_out_div);
610 goto fail;
611 }
612
613 snprintf(clk_name, sizeof(clk_name), "dsi%d_pll_bit_clk", pll_10nm->phy->id);
614
615 /* BIT CLK: DIV_CTRL_3_0 */
616 pll_bit = devm_clk_hw_register_divider_parent_hw(dev, clk_name,
617 pll_out_div, CLK_SET_RATE_PARENT,
618 pll_10nm->phy->base + REG_DSI_10nm_PHY_CMN_CLK_CFG0,
619 0, 4, CLK_DIVIDER_ONE_BASED, &pll_10nm->postdiv_lock);
620 if (IS_ERR(pll_bit)) {
621 ret = PTR_ERR(pll_bit);
622 goto fail;
623 }
624
625 snprintf(clk_name, sizeof(clk_name), "dsi%d_phy_pll_out_byteclk", pll_10nm->phy->id);
626
627 /* DSI Byte clock = VCO_CLK / OUT_DIV / BIT_DIV / 8 */
628 hw = devm_clk_hw_register_fixed_factor_parent_hw(dev, clk_name,
629 pll_bit, CLK_SET_RATE_PARENT, 1, 8);
630 if (IS_ERR(hw)) {
631 ret = PTR_ERR(hw);
632 goto fail;
633 }
634
635 provided_clocks[DSI_BYTE_PLL_CLK] = hw;
636
637 snprintf(clk_name, sizeof(clk_name), "dsi%d_pll_by_2_bit_clk", pll_10nm->phy->id);
638
639 pll_by_2_bit = devm_clk_hw_register_fixed_factor_parent_hw(dev,
640 clk_name, pll_bit, 0, 1, 2);
641 if (IS_ERR(pll_by_2_bit)) {
642 ret = PTR_ERR(pll_by_2_bit);
643 goto fail;
644 }
645
646 snprintf(clk_name, sizeof(clk_name), "dsi%d_pll_post_out_div_clk", pll_10nm->phy->id);
647
648 pll_post_out_div = devm_clk_hw_register_fixed_factor_parent_hw(dev,
649 clk_name, pll_out_div, 0, 1, 4);
650 if (IS_ERR(pll_post_out_div)) {
651 ret = PTR_ERR(pll_post_out_div);
652 goto fail;
653 }
654
655 snprintf(clk_name, sizeof(clk_name), "dsi%d_pclk_mux", pll_10nm->phy->id);
656
657 pclk_mux = devm_clk_hw_register_mux_parent_hws(dev, clk_name,
658 ((const struct clk_hw *[]){
659 pll_bit,
660 pll_by_2_bit,
661 pll_out_div,
662 pll_post_out_div,
663 }), 4, 0, pll_10nm->phy->base +
664 REG_DSI_10nm_PHY_CMN_CLK_CFG1, 0, 2, 0, NULL);
665 if (IS_ERR(pclk_mux)) {
666 ret = PTR_ERR(pclk_mux);
667 goto fail;
668 }
669
670 snprintf(clk_name, sizeof(clk_name), "dsi%d_phy_pll_out_dsiclk", pll_10nm->phy->id);
671
672 /* PIX CLK DIV : DIV_CTRL_7_4*/
673 hw = devm_clk_hw_register_divider_parent_hw(dev, clk_name, pclk_mux,
674 0, pll_10nm->phy->base + REG_DSI_10nm_PHY_CMN_CLK_CFG0,
675 4, 4, CLK_DIVIDER_ONE_BASED, &pll_10nm->postdiv_lock);
676 if (IS_ERR(hw)) {
677 ret = PTR_ERR(hw);
678 goto fail;
679 }
680
681 provided_clocks[DSI_PIXEL_PLL_CLK] = hw;
682
683 return 0;
684
685 fail:
686
687 return ret;
688 }
689
dsi_pll_10nm_init(struct msm_dsi_phy * phy)690 static int dsi_pll_10nm_init(struct msm_dsi_phy *phy)
691 {
692 struct platform_device *pdev = phy->pdev;
693 struct dsi_pll_10nm *pll_10nm;
694 int ret;
695
696 pll_10nm = devm_kzalloc(&pdev->dev, sizeof(*pll_10nm), GFP_KERNEL);
697 if (!pll_10nm)
698 return -ENOMEM;
699
700 DBG("DSI PLL%d", phy->id);
701
702 pll_10nm_list[phy->id] = pll_10nm;
703
704 spin_lock_init(&pll_10nm->postdiv_lock);
705
706 pll_10nm->phy = phy;
707
708 ret = pll_10nm_register(pll_10nm, phy->provided_clocks->hws);
709 if (ret) {
710 DRM_DEV_ERROR(&pdev->dev, "failed to register PLL: %d\n", ret);
711 return ret;
712 }
713
714 phy->vco_hw = &pll_10nm->clk_hw;
715
716 /* TODO: Remove this when we have proper display handover support */
717 msm_dsi_phy_pll_save_state(phy);
718
719 return 0;
720 }
721
dsi_phy_hw_v3_0_is_pll_on(struct msm_dsi_phy * phy)722 static int dsi_phy_hw_v3_0_is_pll_on(struct msm_dsi_phy *phy)
723 {
724 void __iomem *base = phy->base;
725 u32 data = 0;
726
727 data = dsi_phy_read(base + REG_DSI_10nm_PHY_CMN_PLL_CNTRL);
728 mb(); /* make sure read happened */
729
730 return (data & BIT(0));
731 }
732
dsi_phy_hw_v3_0_config_lpcdrx(struct msm_dsi_phy * phy,bool enable)733 static void dsi_phy_hw_v3_0_config_lpcdrx(struct msm_dsi_phy *phy, bool enable)
734 {
735 void __iomem *lane_base = phy->lane_base;
736 int phy_lane_0 = 0; /* TODO: Support all lane swap configs */
737
738 /*
739 * LPRX and CDRX need to enabled only for physical data lane
740 * corresponding to the logical data lane 0
741 */
742 if (enable)
743 dsi_phy_write(lane_base +
744 REG_DSI_10nm_PHY_LN_LPRX_CTRL(phy_lane_0), 0x3);
745 else
746 dsi_phy_write(lane_base +
747 REG_DSI_10nm_PHY_LN_LPRX_CTRL(phy_lane_0), 0);
748 }
749
dsi_phy_hw_v3_0_lane_settings(struct msm_dsi_phy * phy)750 static void dsi_phy_hw_v3_0_lane_settings(struct msm_dsi_phy *phy)
751 {
752 int i;
753 u8 tx_dctrl[] = { 0x00, 0x00, 0x00, 0x04, 0x01 };
754 void __iomem *lane_base = phy->lane_base;
755 struct dsi_phy_10nm_tuning_cfg *tuning_cfg = phy->tuning_cfg;
756
757 if (phy->cfg->quirks & DSI_PHY_10NM_QUIRK_OLD_TIMINGS)
758 tx_dctrl[3] = 0x02;
759
760 /* Strength ctrl settings */
761 for (i = 0; i < 5; i++) {
762 dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_LPTX_STR_CTRL(i),
763 0x55);
764 /*
765 * Disable LPRX and CDRX for all lanes. And later on, it will
766 * be only enabled for the physical data lane corresponding
767 * to the logical data lane 0
768 */
769 dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_LPRX_CTRL(i), 0);
770 dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_PIN_SWAP(i), 0x0);
771 dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_HSTX_STR_CTRL(i),
772 0x88);
773 }
774
775 dsi_phy_hw_v3_0_config_lpcdrx(phy, true);
776
777 /* other settings */
778 for (i = 0; i < 5; i++) {
779 dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_CFG0(i), 0x0);
780 dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_CFG1(i), 0x0);
781 dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_CFG2(i), 0x0);
782 dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_CFG3(i),
783 i == 4 ? 0x80 : 0x0);
784
785 /* platform specific dsi phy drive strength adjustment */
786 dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_OFFSET_TOP_CTRL(i),
787 tuning_cfg->rescode_offset_top[i]);
788 dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_OFFSET_BOT_CTRL(i),
789 tuning_cfg->rescode_offset_bot[i]);
790
791 dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_TX_DCTRL(i),
792 tx_dctrl[i]);
793 }
794
795 if (!(phy->cfg->quirks & DSI_PHY_10NM_QUIRK_OLD_TIMINGS)) {
796 /* Toggle BIT 0 to release freeze I/0 */
797 dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_TX_DCTRL(3), 0x05);
798 dsi_phy_write(lane_base + REG_DSI_10nm_PHY_LN_TX_DCTRL(3), 0x04);
799 }
800 }
801
dsi_10nm_phy_enable(struct msm_dsi_phy * phy,struct msm_dsi_phy_clk_request * clk_req)802 static int dsi_10nm_phy_enable(struct msm_dsi_phy *phy,
803 struct msm_dsi_phy_clk_request *clk_req)
804 {
805 int ret;
806 u32 status;
807 u32 const delay_us = 5;
808 u32 const timeout_us = 1000;
809 struct msm_dsi_dphy_timing *timing = &phy->timing;
810 void __iomem *base = phy->base;
811 struct dsi_phy_10nm_tuning_cfg *tuning_cfg = phy->tuning_cfg;
812 u32 data;
813
814 DBG("");
815
816 if (msm_dsi_dphy_timing_calc_v3(timing, clk_req)) {
817 DRM_DEV_ERROR(&phy->pdev->dev,
818 "%s: D-PHY timing calculation failed\n", __func__);
819 return -EINVAL;
820 }
821
822 if (dsi_phy_hw_v3_0_is_pll_on(phy))
823 pr_warn("PLL turned on before configuring PHY\n");
824
825 /* wait for REFGEN READY */
826 ret = readl_poll_timeout_atomic(base + REG_DSI_10nm_PHY_CMN_PHY_STATUS,
827 status, (status & BIT(0)),
828 delay_us, timeout_us);
829 if (ret) {
830 pr_err("Ref gen not ready. Aborting\n");
831 return -EINVAL;
832 }
833
834 /* de-assert digital and pll power down */
835 data = BIT(6) | BIT(5);
836 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_CTRL_0, data);
837
838 /* Assert PLL core reset */
839 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_PLL_CNTRL, 0x00);
840
841 /* turn off resync FIFO */
842 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_RBUF_CTRL, 0x00);
843
844 /* Select MS1 byte-clk */
845 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_GLBL_CTRL, 0x10);
846
847 /* Enable LDO with platform specific drive level/amplitude adjustment */
848 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_VREG_CTRL,
849 tuning_cfg->vreg_ctrl);
850
851 /* Configure PHY lane swap (TODO: we need to calculate this) */
852 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_LANE_CFG0, 0x21);
853 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_LANE_CFG1, 0x84);
854
855 /* DSI PHY timings */
856 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_0,
857 timing->hs_halfbyte_en);
858 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_1,
859 timing->clk_zero);
860 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_2,
861 timing->clk_prepare);
862 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_3,
863 timing->clk_trail);
864 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_4,
865 timing->hs_exit);
866 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_5,
867 timing->hs_zero);
868 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_6,
869 timing->hs_prepare);
870 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_7,
871 timing->hs_trail);
872 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_8,
873 timing->hs_rqst);
874 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_9,
875 timing->ta_go | (timing->ta_sure << 3));
876 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_10,
877 timing->ta_get);
878 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_TIMING_CTRL_11,
879 0x00);
880
881 /* Remove power down from all blocks */
882 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_CTRL_0, 0x7f);
883
884 /* power up lanes */
885 data = dsi_phy_read(base + REG_DSI_10nm_PHY_CMN_CTRL_0);
886
887 /* TODO: only power up lanes that are used */
888 data |= 0x1F;
889 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_CTRL_0, data);
890 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_LANE_CTRL0, 0x1F);
891
892 /* Select full-rate mode */
893 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_CTRL_2, 0x40);
894
895 ret = dsi_10nm_set_usecase(phy);
896 if (ret) {
897 DRM_DEV_ERROR(&phy->pdev->dev, "%s: set pll usecase failed, %d\n",
898 __func__, ret);
899 return ret;
900 }
901
902 /* DSI lane settings */
903 dsi_phy_hw_v3_0_lane_settings(phy);
904
905 DBG("DSI%d PHY enabled", phy->id);
906
907 return 0;
908 }
909
dsi_10nm_phy_disable(struct msm_dsi_phy * phy)910 static void dsi_10nm_phy_disable(struct msm_dsi_phy *phy)
911 {
912 void __iomem *base = phy->base;
913 u32 data;
914
915 DBG("");
916
917 if (dsi_phy_hw_v3_0_is_pll_on(phy))
918 pr_warn("Turning OFF PHY while PLL is on\n");
919
920 dsi_phy_hw_v3_0_config_lpcdrx(phy, false);
921 data = dsi_phy_read(base + REG_DSI_10nm_PHY_CMN_CTRL_0);
922
923 /* disable all lanes */
924 data &= ~0x1F;
925 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_CTRL_0, data);
926 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_LANE_CTRL0, 0);
927
928 /* Turn off all PHY blocks */
929 dsi_phy_write(base + REG_DSI_10nm_PHY_CMN_CTRL_0, 0x00);
930 /* make sure phy is turned off */
931 wmb();
932
933 DBG("DSI%d PHY disabled", phy->id);
934 }
935
dsi_10nm_phy_parse_dt(struct msm_dsi_phy * phy)936 static int dsi_10nm_phy_parse_dt(struct msm_dsi_phy *phy)
937 {
938 struct device *dev = &phy->pdev->dev;
939 struct dsi_phy_10nm_tuning_cfg *tuning_cfg;
940 s8 offset_top[DSI_LANE_MAX] = { 0 }; /* No offset */
941 s8 offset_bot[DSI_LANE_MAX] = { 0 }; /* No offset */
942 u32 ldo_level = 400; /* 400mV */
943 u8 level;
944 int ret, i;
945
946 tuning_cfg = devm_kzalloc(dev, sizeof(*tuning_cfg), GFP_KERNEL);
947 if (!tuning_cfg)
948 return -ENOMEM;
949
950 /* Drive strength adjustment parameters */
951 ret = of_property_read_u8_array(dev->of_node, "qcom,phy-rescode-offset-top",
952 offset_top, DSI_LANE_MAX);
953 if (ret && ret != -EINVAL) {
954 DRM_DEV_ERROR(dev, "failed to parse qcom,phy-rescode-offset-top, %d\n", ret);
955 return ret;
956 }
957
958 for (i = 0; i < DSI_LANE_MAX; i++) {
959 if (offset_top[i] < -32 || offset_top[i] > 31) {
960 DRM_DEV_ERROR(dev,
961 "qcom,phy-rescode-offset-top value %d is not in range [-32..31]\n",
962 offset_top[i]);
963 return -EINVAL;
964 }
965 tuning_cfg->rescode_offset_top[i] = 0x3f & offset_top[i];
966 }
967
968 ret = of_property_read_u8_array(dev->of_node, "qcom,phy-rescode-offset-bot",
969 offset_bot, DSI_LANE_MAX);
970 if (ret && ret != -EINVAL) {
971 DRM_DEV_ERROR(dev, "failed to parse qcom,phy-rescode-offset-bot, %d\n", ret);
972 return ret;
973 }
974
975 for (i = 0; i < DSI_LANE_MAX; i++) {
976 if (offset_bot[i] < -32 || offset_bot[i] > 31) {
977 DRM_DEV_ERROR(dev,
978 "qcom,phy-rescode-offset-bot value %d is not in range [-32..31]\n",
979 offset_bot[i]);
980 return -EINVAL;
981 }
982 tuning_cfg->rescode_offset_bot[i] = 0x3f & offset_bot[i];
983 }
984
985 /* Drive level/amplitude adjustment parameters */
986 ret = of_property_read_u32(dev->of_node, "qcom,phy-drive-ldo-level", &ldo_level);
987 if (ret && ret != -EINVAL) {
988 DRM_DEV_ERROR(dev, "failed to parse qcom,phy-drive-ldo-level, %d\n", ret);
989 return ret;
990 }
991
992 switch (ldo_level) {
993 case 375:
994 level = 0;
995 break;
996 case 400:
997 level = 1;
998 break;
999 case 425:
1000 level = 2;
1001 break;
1002 case 450:
1003 level = 3;
1004 break;
1005 case 475:
1006 level = 4;
1007 break;
1008 case 500:
1009 level = 5;
1010 break;
1011 default:
1012 DRM_DEV_ERROR(dev, "qcom,phy-drive-ldo-level %d is not supported\n", ldo_level);
1013 return -EINVAL;
1014 }
1015 tuning_cfg->vreg_ctrl = 0x58 | (0x7 & level);
1016
1017 phy->tuning_cfg = tuning_cfg;
1018
1019 return 0;
1020 }
1021
1022 static const struct regulator_bulk_data dsi_phy_10nm_regulators[] = {
1023 { .supply = "vdds", .init_load_uA = 36000 },
1024 };
1025
1026 const struct msm_dsi_phy_cfg dsi_phy_10nm_cfgs = {
1027 .has_phy_lane = true,
1028 .regulator_data = dsi_phy_10nm_regulators,
1029 .num_regulators = ARRAY_SIZE(dsi_phy_10nm_regulators),
1030 .ops = {
1031 .enable = dsi_10nm_phy_enable,
1032 .disable = dsi_10nm_phy_disable,
1033 .pll_init = dsi_pll_10nm_init,
1034 .save_pll_state = dsi_10nm_pll_save_state,
1035 .restore_pll_state = dsi_10nm_pll_restore_state,
1036 .parse_dt_properties = dsi_10nm_phy_parse_dt,
1037 },
1038 .min_pll_rate = 1000000000UL,
1039 .max_pll_rate = 3500000000UL,
1040 .io_start = { 0xae94400, 0xae96400 },
1041 .num_dsi_phy = 2,
1042 };
1043
1044 const struct msm_dsi_phy_cfg dsi_phy_10nm_8998_cfgs = {
1045 .has_phy_lane = true,
1046 .regulator_data = dsi_phy_10nm_regulators,
1047 .num_regulators = ARRAY_SIZE(dsi_phy_10nm_regulators),
1048 .ops = {
1049 .enable = dsi_10nm_phy_enable,
1050 .disable = dsi_10nm_phy_disable,
1051 .pll_init = dsi_pll_10nm_init,
1052 .save_pll_state = dsi_10nm_pll_save_state,
1053 .restore_pll_state = dsi_10nm_pll_restore_state,
1054 .parse_dt_properties = dsi_10nm_phy_parse_dt,
1055 },
1056 .min_pll_rate = 1000000000UL,
1057 .max_pll_rate = 3500000000UL,
1058 .io_start = { 0xc994400, 0xc996400 },
1059 .num_dsi_phy = 2,
1060 .quirks = DSI_PHY_10NM_QUIRK_OLD_TIMINGS,
1061 };
1062