1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * (C) Copyright 2013 Atmel Corporation
4 * Josh Wu <josh.wu@atmel.com>
5 */
6
7 #include <common.h>
8 #include <asm/io.h>
9 #include <asm/arch/at91sam9x5_matrix.h>
10 #include <asm/arch/at91sam9_smc.h>
11 #include <asm/arch/at91_common.h>
12 #include <asm/arch/at91_rstc.h>
13 #include <asm/arch/at91_pio.h>
14 #include <asm/arch/clk.h>
15 #include <debug_uart.h>
16 #include <lcd.h>
17 #include <atmel_hlcdc.h>
18 #include <netdev.h>
19
20 #ifdef CONFIG_LCD_INFO
21 #include <nand.h>
22 #include <version.h>
23 #endif
24
25 DECLARE_GLOBAL_DATA_PTR;
26
27 /* ------------------------------------------------------------------------- */
28 /*
29 * Miscelaneous platform dependent initialisations
30 */
31 #ifdef CONFIG_NAND_ATMEL
at91sam9n12ek_nand_hw_init(void)32 static void at91sam9n12ek_nand_hw_init(void)
33 {
34 struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
35 struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
36 unsigned long csa;
37
38 /* Assign CS3 to NAND/SmartMedia Interface */
39 csa = readl(&matrix->ebicsa);
40 csa |= AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA;
41 /* Configure databus */
42 csa &= ~AT91_MATRIX_NFD0_ON_D16; /* nandflash connect to D0~D15 */
43 /* Configure IO drive */
44 csa |= AT91_MATRIX_EBI_EBI_IOSR_NORMAL;
45
46 writel(csa, &matrix->ebicsa);
47
48 /* Configure SMC CS3 for NAND/SmartMedia */
49 writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
50 AT91_SMC_SETUP_NRD(2) | AT91_SMC_SETUP_NCS_RD(0),
51 &smc->cs[3].setup);
52 writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(5) |
53 AT91_SMC_PULSE_NRD(4) | AT91_SMC_PULSE_NCS_RD(6),
54 &smc->cs[3].pulse);
55 writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(7),
56 &smc->cs[3].cycle);
57 writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
58 AT91_SMC_MODE_EXNW_DISABLE |
59 #ifdef CONFIG_SYS_NAND_DBW_16
60 AT91_SMC_MODE_DBW_16 |
61 #else /* CONFIG_SYS_NAND_DBW_8 */
62 AT91_SMC_MODE_DBW_8 |
63 #endif
64 AT91_SMC_MODE_TDF_CYCLE(1),
65 &smc->cs[3].mode);
66
67 /* Configure RDY/BSY pin */
68 at91_set_pio_input(AT91_PIO_PORTD, 5, 1);
69
70 /* Configure ENABLE pin for NandFlash */
71 at91_set_pio_output(AT91_PIO_PORTD, 4, 1);
72
73 at91_pio3_set_a_periph(AT91_PIO_PORTD, 0, 1); /* NAND OE */
74 at91_pio3_set_a_periph(AT91_PIO_PORTD, 1, 1); /* NAND WE */
75 at91_pio3_set_a_periph(AT91_PIO_PORTD, 2, 1); /* ALE */
76 at91_pio3_set_a_periph(AT91_PIO_PORTD, 3, 1); /* CLE */
77 }
78 #endif
79
80 #ifdef CONFIG_LCD
81 vidinfo_t panel_info = {
82 .vl_col = 480,
83 .vl_row = 272,
84 .vl_clk = 9000000,
85 .vl_bpix = LCD_BPP,
86 .vl_sync = 0,
87 .vl_tft = 1,
88 .vl_hsync_len = 5,
89 .vl_left_margin = 8,
90 .vl_right_margin = 43,
91 .vl_vsync_len = 10,
92 .vl_upper_margin = 4,
93 .vl_lower_margin = 12,
94 .mmio = ATMEL_BASE_LCDC,
95 };
96
lcd_enable(void)97 void lcd_enable(void)
98 {
99 at91_set_pio_output(AT91_PIO_PORTC, 25, 0); /* power up */
100 }
101
lcd_disable(void)102 void lcd_disable(void)
103 {
104 at91_set_pio_output(AT91_PIO_PORTC, 25, 1); /* power down */
105 }
106
107 #ifdef CONFIG_LCD_INFO
lcd_show_board_info(void)108 void lcd_show_board_info(void)
109 {
110 ulong dram_size, nand_size;
111 int i;
112 char temp[32];
113
114 lcd_printf("%s\n", U_BOOT_VERSION);
115 lcd_printf("ATMEL Corp\n");
116 lcd_printf("at91@atmel.com\n");
117 lcd_printf("%s CPU at %s MHz\n",
118 ATMEL_CPU_NAME,
119 strmhz(temp, get_cpu_clk_rate()));
120
121 dram_size = 0;
122 for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
123 dram_size += gd->bd->bi_dram[i].size;
124 nand_size = 0;
125 for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
126 nand_size += get_nand_dev_by_index(i)->size;
127 lcd_printf(" %ld MB SDRAM, %ld MB NAND\n",
128 dram_size >> 20,
129 nand_size >> 20);
130 }
131 #endif /* CONFIG_LCD_INFO */
132 #endif /* CONFIG_LCD */
133
134 #ifdef CONFIG_KS8851_MLL
at91sam9n12ek_ks8851_hw_init(void)135 void at91sam9n12ek_ks8851_hw_init(void)
136 {
137 struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
138
139 writel(AT91_SMC_SETUP_NWE(2) | AT91_SMC_SETUP_NCS_WR(0) |
140 AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
141 &smc->cs[2].setup);
142 writel(AT91_SMC_PULSE_NWE(7) | AT91_SMC_PULSE_NCS_WR(7) |
143 AT91_SMC_PULSE_NRD(7) | AT91_SMC_PULSE_NCS_RD(7),
144 &smc->cs[2].pulse);
145 writel(AT91_SMC_CYCLE_NWE(9) | AT91_SMC_CYCLE_NRD(9),
146 &smc->cs[2].cycle);
147 writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
148 AT91_SMC_MODE_EXNW_DISABLE |
149 AT91_SMC_MODE_BAT | AT91_SMC_MODE_DBW_16 |
150 AT91_SMC_MODE_TDF_CYCLE(1),
151 &smc->cs[2].mode);
152
153 /* Configure NCS2 PIN */
154 at91_pio3_set_b_periph(AT91_PIO_PORTD, 19, 0);
155 }
156 #endif
157
158 #ifdef CONFIG_USB_ATMEL
at91sam9n12ek_usb_hw_init(void)159 void at91sam9n12ek_usb_hw_init(void)
160 {
161 at91_set_pio_output(AT91_PIO_PORTB, 7, 0);
162 }
163 #endif
164
165 #ifdef CONFIG_DEBUG_UART_BOARD_INIT
board_debug_uart_init(void)166 void board_debug_uart_init(void)
167 {
168 at91_seriald_hw_init();
169 }
170 #endif
171
172 #ifdef CONFIG_BOARD_EARLY_INIT_F
board_early_init_f(void)173 int board_early_init_f(void)
174 {
175 #ifdef CONFIG_DEBUG_UART
176 debug_uart_init();
177 #endif
178 return 0;
179 }
180 #endif
181
board_init(void)182 int board_init(void)
183 {
184 /* adress of boot parameters */
185 gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
186
187 #ifdef CONFIG_NAND_ATMEL
188 at91sam9n12ek_nand_hw_init();
189 #endif
190
191 #ifdef CONFIG_LCD
192 at91_lcd_hw_init();
193 #endif
194
195 #ifdef CONFIG_KS8851_MLL
196 at91sam9n12ek_ks8851_hw_init();
197 #endif
198
199 #ifdef CONFIG_USB_ATMEL
200 at91sam9n12ek_usb_hw_init();
201 #endif
202
203 return 0;
204 }
205
206 #ifdef CONFIG_KS8851_MLL
board_eth_init(bd_t * bis)207 int board_eth_init(bd_t *bis)
208 {
209 return ks8851_mll_initialize(0, CONFIG_KS8851_MLL_BASEADDR);
210 }
211 #endif
212
dram_init(void)213 int dram_init(void)
214 {
215 gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
216 CONFIG_SYS_SDRAM_SIZE);
217 return 0;
218 }
219
220 #if defined(CONFIG_SPL_BUILD)
221 #include <spl.h>
222 #include <nand.h>
223
at91_spl_board_init(void)224 void at91_spl_board_init(void)
225 {
226 #ifdef CONFIG_SD_BOOT
227 at91_mci_hw_init();
228 #elif CONFIG_NAND_BOOT
229 at91sam9n12ek_nand_hw_init();
230 #elif CONFIG_SPI_BOOT
231 at91_spi0_hw_init(1 << 4);
232 #endif
233 }
234
235 #include <asm/arch/atmel_mpddrc.h>
ddr2_conf(struct atmel_mpddrc_config * ddr2)236 static void ddr2_conf(struct atmel_mpddrc_config *ddr2)
237 {
238 ddr2->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM);
239
240 ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
241 ATMEL_MPDDRC_CR_NR_ROW_13 |
242 ATMEL_MPDDRC_CR_CAS_DDR_CAS3 |
243 ATMEL_MPDDRC_CR_NB_8BANKS |
244 ATMEL_MPDDRC_CR_DECOD_INTERLEAVED);
245
246 ddr2->rtr = 0x411;
247
248 ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |
249 2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |
250 2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET |
251 8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET |
252 2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET |
253 2 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET |
254 2 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET |
255 2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET);
256
257 ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET |
258 200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET |
259 19 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET |
260 18 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET);
261
262 ddr2->tpr2 = (2 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET |
263 3 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET |
264 7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET |
265 2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET);
266 }
267
mem_init(void)268 void mem_init(void)
269 {
270 struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
271 struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
272 struct atmel_mpddrc_config ddr2;
273 unsigned long csa;
274
275 ddr2_conf(&ddr2);
276
277 /* enable DDR2 clock */
278 writel(AT91_PMC_DDR, &pmc->scer);
279
280 /* Chip select 1 is for DDR2/SDRAM */
281 csa = readl(&matrix->ebicsa);
282 csa |= AT91_MATRIX_EBI_CS1A_SDRAMC;
283 csa &= ~AT91_MATRIX_EBI_DBPU_OFF;
284 csa |= AT91_MATRIX_EBI_DBPD_OFF;
285 csa |= AT91_MATRIX_EBI_EBI_IOSR_NORMAL;
286 writel(csa, &matrix->ebicsa);
287
288 /* DDRAM2 Controller initialize */
289 ddr2_init(ATMEL_BASE_DDRSDRC, ATMEL_BASE_CS1, &ddr2);
290 }
291 #endif
292